I am talking about rear shock valves. wires go from the module (inside the trunk on the left) to the shocks. I reached the left shock and to reach the right one I will tie the cable (with sleeve of course) UNDER the car, but it's close to the exhaust.
anyway. we did parameterization for the module tonight, online with .
I added module 14 to gateway installation list;
I recoded 03 module for ;
I recoded 17 cluster for ;
I am now left with these errors in module
Code:
Address 14: Susp. Elect. Labels: 5Q0-907-376.clb
Control Module Part Number: 5Q0 907 376 B HW: 5Q0 907 376 A
Component and/or Version: DAEMPFUNGS-SG H17 0121
Software Coding:
Work Shop Code:
ASAM Dataset: EV_DRCONTITEMIC 001019 (VW37)
ROD: EV_DRCONTITEMIC_VW37.rod
VCID: 3829D4F302D22547317-806C
9 Faults Found:
278272 - Basic Setting of Deflected Position not Performed
C10C5 00 [137] - -
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:05
835584 - MIL Request Signal Active (Check TCM for errors too!)
P1624 00 [137] - -
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:26
835328 - MIL Request Signal Active (Check TCM for errors too!)
P1624 00 [008] - -
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 7
Fault Frequency: 1
Reset counter: 165
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:05
36105 - Chassis Acceleration Sensor; Rear
C10BA 01 [009] - Electrical Failure
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:05
198154 - Rear Left Ride-Height Sensor
C1036 15 [009] - Open or Short to Plus
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:05
36363 - Valve for Damping Adjustment Front Left
C1040 13 [137] - Open Circuit
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:23
36619 - Valve for Damping Adjustment Front Right
C1041 13 [137] - Open Circuit
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:23
36875 - Valve for Damping Adjustment Rear Left
C1042 13 [137] - Open Circuit
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:23
37131 - Valve for Damping Adjustment Rear Right
C1043 13 [137] - Open Circuit
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 125
Mileage: 36630 km
Date: 2019.12.15
Time: 00:25:23
two sensors and the 4 shocks are still disconnected so that's ok. after I replace the shocks and connect everything I will try basic settings.
what is weird is that I cannot see settings on any menu. is supposed to appear under Driving MODE menu (which is a , and my car has it from stock).
I remember, when I did retrofit I enabled one bit in gateway coding, thanks to experimental coding. after that showed into Driving MODE menu.
so I looked for something similar for and I enabled BYTE 9 BIT 7 in gateway experimental coding.
still I don't see any into any menu.
I wonder if there is something else to enable, maybe in 5F?
there is very little information on retrofit as it's not very popular.
some Jimmy did it in Singapore, did a few actually, but he does not answers emails or social media.
somebody on drive2.ru did it on Octavia but I don't know how to get ahold of him.
maybe it just needs basic settings, we'll see.
fingers crossed.