- Joined
- Feb 26, 2016
- Messages
- 152
- Reaction score
- 35
- Location
- Czech Republic
- VCDS Serial number
- C?ID=91614
Hello
I put massage and ventilated seats from prefacelift Audi A6 C7 Avant to Facelift Audi A6 Avant C7.5.
There was original textile electric seats with driver memory function, so i have to add only passanger side cables from right door.
I swapped front Climate control:
Original: 4G0 820 043 CD, Coding: 36821178250000 (labels used: 4G0-820-043-4Z.clb)
New one: 4G0 820 043 BM (it was replaced 4G0820043CE in ETKA)
Also swapped rear Climate control: (due rear seats heating + made cables)
Original: 4G0 919 158 Q, coding 20
New One: 4G0 919 158 K
Coding of front clima was not documented in my HEX-CAN so i used from the original one: 36821178250000
There was not working Cooling and seats ventilation worked only 3-5 sec, also massage only shown for while on MMI and does not work. (yes i made CP remove). Clima unit anyway worked optically fine and there was no error in scan.
Then I used HEX-NET cable from my friend and made coding from VCDS experimental Beta - but also without success - cooling, ventilated seats and massage does not work.
I try write here all scan of all units in car (i got car later). I have error on both seats memory units but they are reachable by VCDS and there is also error on instrument cluster after i swap front clima panel.
I tried to coding 09 - central electronics - but there is no label file: (i would like to code, that there is no front heating, because it take care about seats units)
Here is original coding 09 module:
When will you have (experimental) coding of Central El. - V2 ?
Have someone did this retrofit with success ?
Thank you!
P.S. I plan next week to buy new HEX-V2 unlimited, hope it (except Wifi and mobile app) works same way like HEX-NET... (working experimental coding and beta versions i need)
I put massage and ventilated seats from prefacelift Audi A6 C7 Avant to Facelift Audi A6 Avant C7.5.
There was original textile electric seats with driver memory function, so i have to add only passanger side cables from right door.
I swapped front Climate control:
Original: 4G0 820 043 CD, Coding: 36821178250000 (labels used: 4G0-820-043-4Z.clb)
New one: 4G0 820 043 BM (it was replaced 4G0820043CE in ETKA)
Also swapped rear Climate control: (due rear seats heating + made cables)
Original: 4G0 919 158 Q, coding 20
New One: 4G0 919 158 K
Coding of front clima was not documented in my HEX-CAN so i used from the original one: 36821178250000
There was not working Cooling and seats ventilation worked only 3-5 sec, also massage only shown for while on MMI and does not work. (yes i made CP remove). Clima unit anyway worked optically fine and there was no error in scan.
Then I used HEX-NET cable from my friend and made coding from VCDS experimental Beta - but also without success - cooling, ventilated seats and massage does not work.
I try write here all scan of all units in car (i got car later). I have error on both seats memory units but they are reachable by VCDS and there is also error on instrument cluster after i swap front clima panel.
I tried to coding 09 - central electronics - but there is no label file: (i would like to code, that there is no front heating, because it take care about seats units)
Here is original coding 09 module:
Code:
Address 09: Cent. Elect. (J519) Labels: Redir Fail!
Part No SW: 4H0 907 063 DG HW: 4H0 907 063 AG
Component: BCM1 2.0 H20 0311
Revision: 14020001 Serial number: 00001172356502
Coding: 0105001440349FE2C9014087A0001800CF9CC7082E08020180000894E101170200400009090000
Shop #: WSC 02391 785 00200
VCID: 70EBB6F1A32669C4D1-8024
When will you have (experimental) coding of Central El. - V2 ?
Have someone did this retrofit with success ?
Thank you!
P.S. I plan next week to buy new HEX-V2 unlimited, hope it (except Wifi and mobile app) works same way like HEX-NET... (working experimental coding and beta versions i need)