Hello everyone! 
I recently had a catastrophic leak from my mechatronic unit resulting in loss of drive and a trail of oil wherever I went!
I removed the unit and sent it away to be refurbished, and now it is fitted again.
The car does drive, but it's not at all smooth, with some revving between some of the up-shifts, and it has also lost the ability to creep while in reverse, making parking manoeuvres quite tricky.
Most likely, I just need to run the basic settings on the gearbox, following this guide: http://wiki.ross-tech.com/wiki/index.php/7-Speed_Direct_Shift_Gearbox_(DSG/0AM)
However, since I've never done this before (or anything else with VCDS), I'm seeking a little bit of reassurance that this is the correct approach to take.
Hopefully, it will be a relatively easy task!
Here's a full auto scan:
As you can see there are three faults relating to both clutches.
The guide says that there should be no faults stored in the TCM. Should I simply clear those errors prior to running the basic settings, or are these errors something to be worried about?
Many thanks for reading!
Edit:
Looking at the mileage, I think those faults could have been from before I replaced the unit.
Scan mileage: 122980km
Fault1 miles: 122821 km
Fault1 miles: 122836 km
Fault1 miles: 122868 km
I don't think I've driven 120km since re-fitting.
I recently had a catastrophic leak from my mechatronic unit resulting in loss of drive and a trail of oil wherever I went!
I removed the unit and sent it away to be refurbished, and now it is fitted again.
The car does drive, but it's not at all smooth, with some revving between some of the up-shifts, and it has also lost the ability to creep while in reverse, making parking manoeuvres quite tricky.
Most likely, I just need to run the basic settings on the gearbox, following this guide: http://wiki.ross-tech.com/wiki/index.php/7-Speed_Direct_Shift_Gearbox_(DSG/0AM)
However, since I've never done this before (or anything else with VCDS), I'm seeking a little bit of reassurance that this is the correct approach to take.
Hopefully, it will be a relatively easy task!
Here's a full auto scan:
Code:
Thursday,04,July,2019,17:16:32:19315
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 8.1 x64
VCDS Version: 19.6.1.0 (x64) HEX-V2 CB: 0.4508.4
Data version: 20190529 DS308.0
www.Ross-Tech.com
VIN: ******5P********* License Plate: *******
Mileage: 122980km-76416mi Repair Order:
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: 5P-SE35 (7N0)
Scan: 01 02 03 08 09 15 16 17 19 25 2E 42 44 46 52 56 62 72
VIN: ******5P********* Mileage: 122980km-76416miles
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: Malfunction 0010
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
2E-Media Player 3 -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
56-Radio -- Status: OK 0000
62-Door, Rear Left -- Status: OK 0000
72-Door, Rear Right -- Status: OK 0000
-------------------------------------------------------------------------------
Address 01: Engine (J623-CAYC) Labels:. 03L-906-023-CAY.clb
Part No SW: 03L 906 023 LJ HW: 03L 906 023 KL
Component: R4 1.6l TDI H43 9977
Revision: --H43--- Serial number:
Coding: 00254016032500080000
Shop #: WSC 06402 785 00200
ASAM Dataset: EV_ECM16TDI02103L906023LJ 003013
ROD: EV_ECM16TDI02103L997557A.rod
VCID: 79AE1850A95DE5FF8D7-802C
No fault code found.
Readiness: 0 0 0 0 0
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 0AM-927-769.clb
Part No SW: 0AM 300 053 D HW: 0AM 927 769 D
Component: GSG DSG AG7 431 3070
Revision: 00043014 Serial number: CU501203136108
Coding: 0000020
Shop #: WSC 06402 785 00200
VCID: 2D06FC002115895F51F-8078
3 Faults Found:
006011 - Clutch 1
P177B - 003 - Tolerance Limit Reached - Intermittent
Freeze Frame:
Fault Status: 00100011
Fault Priority: 0
Fault Frequency: 4
Reset counter: 3
Mileage: 122821 km
Time Indication: 0
Date: 2013.11.18
Time: 06:49:02
006012 - Clutch 2
P177C - 003 - Tolerance Limit Reached - Intermittent
Freeze Frame:
Fault Status: 00100011
Fault Priority: 0
Fault Frequency: 15
Reset counter: 10
Mileage: 122836 km
Time Indication: 0
Date: 2013.11.18
Time: 07:00:49
006298 - Clutch 1
P189A - 000 - Clearance too Small - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 0
Fault Frequency: 1
Reset counter: 3
Mileage: 122868 km
Time Indication: 0
Date: 2013.11.21
Time: 07:38:45
-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels:. 1K0-907-379-60EC1F.clb
Part No SW: 1K0 907 379 BJ HW: 1K0 907 379 BJ
Component: ESP MK60EC1 H31 0121
Revision: 00H31001
Coding: 233F4012092500FBC40E02E690200081350000
Shop #: WSC 04941 000 00000
VCID: 7BA20258A3E1D7EF9FB-802E
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5K0-907-044.clb
Part No SW: 5P0 907 044 R HW: 5P0 907 044 R
Component: Climatronic H18 0804
Revision: 00001001
Coding: 0000000002
Shop #: WSC 06402 785 00200
ASAM Dataset: EV_Climatronic A01010
ROD: EV_ClimaAutoBasis_SE35.rod
VCID: 3FDAB648F7F90BCFF33-806A
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels:. 1K0-937-08x-09.clb
Part No SW: 1K0 937 086 N HW: 1K0 937 086 N
Component: BCM PQ35 M+ 110 0651
Revision: 00110 AC
Coding: 46180A3C8025B0E04280008095008104420118A8525D81605C8040000040
Shop #: WSC 04941 000 00000
VCID: 3B22C258E36117EFDFB-806E
Subsystem 1 - Part No: 5P0 955 119 E Labels: 1KX-955-119.CLB
Component: Wischer 21031 26 0611
Coding: 00DB90
Subsystem 2 - Part No: 5P0 951 171 C
Component: Innenraumuebe 009 4865
Subsystem 3 - Part No: 1K0 951 605 C
Component: LIN BACKUP HO H05 1501
1 Fault Found:
01135 - Interior Monitoring Sensors
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 4
Fault Frequency: 17
Reset counter: 227
Mileage: 122801 km
Time Indication: 0
Date: 2013.11.18
Time: 02:09:43
Freeze Frame:
Term 15 Off
Voltage: 12.65 V
OFF
OFF
Term 50 Off
OFF
OFF
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 1K0-909-605.lbl
Part No SW: 1K0 909 605 T HW: 1K0 909 605 T
Component: S9 AIRBAG VW8 020 2300
Revision: 05020000 Serial number: 0038PD2VTKY-
Coding: 0021305
Shop #: WSC 06402 785 00200
VCID: 3D26CC40F17519DFE1F-8068
Subsystem 1 - Serial number: 6332MSME6B153A61E
Subsystem 2 - Serial number: 6342MSME6B414F01E
Subsystem 3 - Serial number: 6351HSME2B636A36E
Subsystem 4 - Serial number: 6361HSME2B4427200
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel (J527) Labels:| 5K0-953-569.clb
Part No SW: 5K0 953 521 AT HW: 5K0 953 569 B
Component: LENKS.MODUL 014 0140
Revision: FF010040 Serial number: 20120322201263
Coding: 1882140002
Shop #: WSC 06402 785 00200
ASAM Dataset: EV_SMLSNGVOLWSXS A01004
ROD: EV_SMLSNGVOLWS.rod
VCID: 7EA40B4CB073C2C7B85-802A
Multifunction steering wheel control module:
Subsystem 1 - Part No SW: 1P0 959 538 C HW: 1P0 959 538 C Labels: 3C8-959-537.CLB
Component: E221__MFL-TAP H02 0102
Coding: E20000
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1
Part No SW: 1P0 920 911 A HW: 1P0 920 911 A
Component: KOMBI H05 0605
Serial number: 00000000000000
Coding: 410B01
Shop #: WSC 131071 1023 2097151
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04113
ROD: EV_Kombi_UDS_VDD_RM09_SK46.rod
VCID: 28080D140277AC77A29-807C
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:. 7N0-907-530-V2.clb
Part No SW: 7N0 907 530 M HW: 1K0 907 951
Component: J533 Gateway H42 1623
Revision: H42 Serial number: 090312F1003971
Coding: 352203
Shop #: WSC 04941 000 00000
VCID: 3A2CC75CEC5B2EE7C4D-806E
No fault code found.
-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H05 0605
Serial number:
Coding: 000000
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03009
ROD: EV_Immo_UDS_VDD_RM09.rod
VCID: 6A8C371CDCFB5E6774D-803E
No fault code found.
-------------------------------------------------------------------------------
Address 2E: Media Player 3 (J650) Labels:. 5N0-035-342.lbl
Part No SW: 6J0 035 342 E HW: 6J0 035 342 E
Component: SG EXT.PLAYER H13 0240
Revision: A1001003 Serial number: 7662137155
Coding: 020000
Shop #: WSC 04941 000 00000
VCID: 2614032C08E3BA07905-8072
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386) Labels:| 3C0-959-70X-GEN4.clb
Part No SW: 3C8 959 701 HW: 3C0 959 793 C
Component: TUER-SG FT 002 0506
Revision: 12110009 Serial number: 0004188494
Coding: 0012B0
Shop #: WSC 06402 785 00200
ASAM Dataset: EV_TSGFPQ35BRFVW46X A04001
ROD: EV_TSGFPQ35BRFVW46X_VW32.rod
VCID: 6D863C00ED15495F11F-8038
Slave Driver:
Subsystem 1 - Part No SW: 3C0 959 704 D HW: 3C0 959 794 C Labels: 1K0-959-70X-GEN4.CLB
Component: J389__TSG-HR 008 1501
Serial number: 00000006543050
Coding: 000290
No fault code found.
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1K0-909-14x-GEN3.clb
Part No: 1K0 909 144 P
Component: EPS_ZFLS Kl. 65 3305
Revision: 00H22000
Shop #: WSC 06402 785 00200
VCID: 372ADE68D349338F3B3-8062
No fault code found.
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387) Labels:| 3C0-959-70X-GEN4.clb
Part No SW: 3C8 959 702 HW: 3C0 959 792 C
Component: TUER-SG BT 002 0506
Revision: 14110009 Serial number: 0004316416
Coding: 0012B0
Shop #: WSC 06402 785 00200
ASAM Dataset: EV_TSGBPQ35BRFVW46X A04001
ROD: EV_TSGBPQ35BRFVW46X_VW32.rod
VCID: 6E843B0CE013B247285-803A
Slave Passenger:
Subsystem 1 - Part No SW: 3C0 959 703 D HW: 3C0 959 795 C Labels: 1K0-959-70X-GEN4.CLB
Component: J388__TSG-HL 007 1501
Serial number: 00000006475111
Coding: 000290
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio (J503) Labels:. 5M0-035-1xx-56.clb
Part No SW: 5P0 035 186 B HW: 5P0 035 186 B
Component: Media2.0 003 0082
Revision: 01000001 Serial number: SEZ1Z3M5054230
Coding: 00040400040000
Shop #: WSC 04941 000 00000
VCID: 2E04FB0C2013F247685-807A
No fault code found.
End----------(Elapsed Time: 01:06, VBatt start/end: 12.3V/12.2V)-----------As you can see there are three faults relating to both clutches.
The guide says that there should be no faults stored in the TCM. Should I simply clear those errors prior to running the basic settings, or are these errors something to be worried about?
Many thanks for reading!
Edit:
Looking at the mileage, I think those faults could have been from before I replaced the unit.
Scan mileage: 122980km
Fault1 miles: 122821 km
Fault1 miles: 122836 km
Fault1 miles: 122868 km
I don't think I've driven 120km since re-fitting.
Last edited:
