Last Saturday I used VCDS on my friend's MY2002 UK TT for the first time. On two runs [before clear and after clear] I got the same message from VCDS for ECU 17 - Instruments.
Edited logs for these sessions are included below.
However, I was able afterwards to successfully run the SRi Reset to show the adapatation values from the instrument panel.
This would appear to be some strange quirk on that cluster and I can't easily rerun VCDS as that was run on a trip.
HOWEVER, the same message appeared on the next run of VCDS on my A8 - on the Auto Transmission - and I've never seen that in over two years of running VCDS agaianst it.
Is this a new problem guys?
Julian
Code:
No Faults Found
or DTCs not supported by controller
or a communication error occurredEdited logs for these sessions are included below.
Code:
Saturday,03,June,2017,15:14:16:53697
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x86
VCDS Version: 17.4.2.3
Data version: 20170505 DS270.4
www.Ross-Tech.com
VIN: TRUZZZ8N621015249 License Plate:
Chassis Type: 8N (8N - Rob-TT)
Scan: 01 02 03 08 15 17 22 35 37 45 55 56 76 77
VIN: TRUZZZ8N621015249
------------------------------------------------------------------------------
Address 17: Instruments Labels: 8Nx-920-xxx-17.lbl
Part No: 8N2 920 980
Component: KOMBI+WEGFAHRS. M73 D14
Coding: 00444
Shop #: WSC 00441
VCID: 74E7BBB1446AEEE718-4B1A
TRUZZZ8N621015249 AUZ5Z0AN050135
No Faults Found
or DTCs not supported by controller
or a communication error occurred
-------------------------------------------------------------------------------
End-------------------------(Elapsed Time: 03:11)--------------------------
Code:
Saturday,03,June,2017,18:58:13:53697
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x86
VCDS Version: 17.4.2.3
Data version: 20170505 DS270.4
www.Ross-Tech.com
VIN: TRUZZZ8N621015249 License Plate:
Chassis Type: 8N (8N - Rob-TT)
Scan: 01 03 08 15 17 22 35 45 56
VIN: TRUZZZ8N621015249
-------------------------------------------------------------------------------
Address 17: Instruments Labels: 8Nx-920-xxx-17.lbl
Part No: 8N2 920 980
Component: KOMBI+WEGFAHRS. M73 D14
Coding: 00444
Shop #: WSC 00441
VCID: 74E7BBB1446AEEE718-4B00
TRUZZZ8N621015249 AUZ5Z0AN050135
No Faults Found
or DTCs not supported by controller
or a communication error occurred
-------------------------------------------------------------------------------
End-------------------------(Elapsed Time: 01:40)--------------------------However, I was able afterwards to successfully run the SRi Reset to show the adapatation values from the instrument panel.
This would appear to be some strange quirk on that cluster and I can't easily rerun VCDS as that was run on a trip.
HOWEVER, the same message appeared on the next run of VCDS on my A8 - on the Auto Transmission - and I've never seen that in over two years of running VCDS agaianst it.
Code:
Monday,05,June,2017,20:21:35:53697
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86
VCDS Version: 17.4.2.3
Data version: 20170505 DS270.4
www.Ross-Tech.com
VIN: WAUZZZ4E35N011492 License Plate:
Chassis Type: 4E (4E0)
Scan: 01 02 03 05 06 07 08 09 0E 15 16 17 18 19 1D 1E 25 34 36 37
38 42 46 47 4F 52 53 56 57 61 62 72 76 77
VIN: WAUZZZ4E35N011492 Mileage: 367960km-228639miles
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 09L-927-760.lbl
Part No SW: 4E0 910 156 F HW: 09L 927 156
Component: AG6 09L 3.0lTDI RdW 0070
Revision: --H01--- Serial number: 0070658
Coding: 0000001
Shop #: WSC 02313 785 00200
VCID: 254196F5EC30C76F5F-8070
Subsystem 1 - Part No: 4E0 910 156 F
Component: AG6 09L 3.0lTDI RdW 0070
No Faults Found
or DTCs not supported by controller
or a communication error occurred
-------------------------------------------------------------------------------
End-------------------------(Elapsed Time: 03:57)--------------------------Is this a new problem guys?
Julian
