Audi A4 B5_Throttle Body Alignment

Status
Not open for further replies.
   #1  

Dragan

Verified VCDS-Lite User
Verified
Joined
Mar 9, 2017
Messages
2
Reaction score
0
Location
TBD
VCDS Serial number
C?ID=301971
Hi. I have a problem with an Audi A4 B5. After I have replaced a battery, I have tried to do a Throttle Body Alignment (TBA), but I didn't manage this. I have done an Auto Scan of the car (attached). I will be very thankful if somebody with more expirience with TBA can look at the scanning and possible send me an suggestion regarding the problem. Thanks in advance.

Code:
VCDS-Lite Version: Release 1.2
Saturday, 11 March 2017, 13:10:28:53892


Chassis Type: 8D - Audi A4 B5
Scan: 01,02,03,08,15,16,17,25,35,37,45,55,56,57,67,75,76,77
 
-------------------------------------------------------------------------------
Address 01: Engine       Labels: Redir Fail!
   Controller: 8D0 906 018 E
   Component: 1.8L R4/5V MOTR G01 0001
   Coding: 04031
   Shop #: WSC 06335
   VCID: 2925AC23C0E1
2 Faults Found:
17987 -  Throttle Actuator (J338): Adaptation Not Started
            P1579 - 35-00 -   -
18010 -  Power Supply Terminal 30: Voltage too Low
            P1602 - 35-10 -   - - Intermittent
Readiness: 0000 0000

-------------------------------------------------------------------------------
Address 02: Auto Trans       Labels: None
   Controller: 01N 927 733 ED
   Component: AG4 Getriebe 01N    4533
   Coding: 00000
   Shop #: WSC 00000
   VCID: 7781BA5B46D5
No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes       Labels: 8E0-614-111-ABS.LBL
   Controller: 8E0 614 111 B
   Component: ABS/EDS 5.3 FRONT   D10
   Coding: 0273004283  
   Shop #: BB 24332
   VCID: 1D4D88F384A9
No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC       Labels: 8D0-820-043-1D.LBL
   Controller: 8D0 820 043 N
   Component: A4     KLIMAAUTOMAT D56
   Coding: 00040
   Shop #: WSC 06335
   VCID: 2B29562BCA1D
No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags       Labels: 8D0-959-655-AI8.LBL
   Controller: 8D0 959 655 F
   Component: Airbag Front+Kopf  0001
   Coding: 00304
   Shop #: WSC 06335
   VCID: 39057C633041
No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments       Labels: 8D0-920-xxx-17.LBL
   Controller: 8D0 920 900 K
   Component: KOMBI+WEGFAHRS. M73 D10
   Coding: 00142
   Shop #: WSC 00000
   VCID: 2B29562BCA1D
   Ident.-Nr. Wegfahrs.:AUZ5Z0X8284322
No fault code found.

-------------------------------------------------------------------------------
Address 25: Immobilizer       Labels: None
   Controller: Bit teA dre sst
   Component: e 17 eingeben          
   VCID: CEEFBFBF19CF
No Faults Found
  or DTCs not supported by controller
  or a communication error ocurred

-------------------------------------------------------------------------------
Address 35: Centr. Locks       Labels: 8D0-862-257.LBL
   Controller: 8D0 862 257 B
   Component: ZV-Pumpe, Funk      D12
   Coding: 12865
   Shop #: WSC 06335
   VCID: 2C2B5537CF13
9 Faults Found:
01367 -  Central Locking Pump Run Time Exceeded (Likely Leak)
            35-00 -   -
01389 -  Tailgate Open Switch (F124)
            29-00 -  Short to Ground
01571 -  Signal for Seat Memory
            29-00 -  Short to Ground
00000 -  End of Output
            00-00 -   -
00991 -  Interior Lights
            28-00 -  Short to Plus
00955 -  Key 1
            09-00 -  Adaptation Limit Surpassed
00956 -  Key 2
            09-00 -  Adaptation Limit Surpassed
00957 -  Key 3
            09-00 -  Adaptation Limit Surpassed
00958 -  Key 4
            09-00 -  Adaptation Limit Surpassed

End   --------------------------------------------------------------------------------------------------
 
Last edited by a moderator:
   #2  

Uwe

Benevolent Dictator
Administrator
Joined
Jan 29, 2014
Messages
49,389
Reaction score
33,864
Location
USA
VCDS Serial number
HC100001
Clear Fault Codes in the ECU first.

Then do a TBA. Ignition must be on, engine but engine must not be running.

More info on this page.

You want the procedure for "Drive-by-Wire (DBW) Engines using KW-1281".

-Uwe-
 
Last edited:
   #3  

Dragan

Verified VCDS-Lite User
Verified
Joined
Mar 9, 2017
Messages
2
Reaction score
0
Location
TBD
VCDS Serial number
C?ID=301971
Hi Uwe and thank you for an so quickly response. I have already tried several times to do an TBA according to description for "Drive-by-Wire (DBW) Engines using KW-1281" but without any success. Each time appeared an error message and TBA does not started at all.
Dragan
 
   #4  

Uwe

Benevolent Dictator
Administrator
Joined
Jan 29, 2014
Messages
49,389
Reaction score
33,864
Location
USA
VCDS Serial number
HC100001
Did you clear fault codes first?

What exactly happens when you try the Basic Setting? If possible, download and install a screen-recording program and make a video.

-Uwe-
 
   #5  

Jack@European_Parts

Gone But Not Forgotten
Professional VCDS User
Joined
Jan 29, 2014
Messages
21,923
Reaction score
9,308
Location
Montgomery, NY, USA
VCDS Serial number
C?ID=57337
In addition to the above Führer's recommendations.......

Ja ja.......

Put a battery charger on this .......check cable setting offset.
Clean and lube TV.

Verify stepper motor of TV can commence 5MM backward before moving forward.

Default controller.

0x01-07-04031 DO IT!
0x01-10-00 SAVE

Cycle ignition key for reset OFF/ON!

0x01-04-060 and 098 in this controller are supported.

JPPSG!

http://forums.ross-tech.com/showthr...essional-Problem-Solver-Guide-quot-JPPSG-quot

http://forums.ross-tech.com/showthread.php?3147-What-is-Jack-talking-about-0x01-08-000

 
Status
Not open for further replies.
Back
Top