Hi All
This my first time of using this software and I’m more of a DIY mechanic (not on electrics, absolute beginner) so keep suggestions in simple terms please.
Long story short, I purchased this car a week ago with 1 warning light flashing, I checked the basics sensors and rings etc, nothing wrong so I took the car to my mate who plugged his Snap-on machine in, code below.
01542 Yaw rate sensor (G202) electrical problem in circuit
01468 System function test activated
After reading up on that code I thought it strange that the ABS light wasn’t flashing so I decided to take the dials out and investigate, sadly under the black layer with the writing on, the tunnels down to the ABS & EML lights had been filled with black silicone to mask the problems.
So this car has been molested before I purchased it, I’m kicking myself for not noticing but I’m stuck with it now so here goes.
I have changed the sensor (1J0 907 657 B) for a second hand one and since then purchased VCDS-Lite and the results are below.
I have noticed that the ABS & Auto trans units have no coding ?
What I have done to try and fix the problem:
1. Basic settings, everything checks out ok except “ERROR not available” in group 069 and also on measuring block 006
2. Coding ABS unit to no avail, labels below if anyone can tell me what codes I should be using
3. Tracking aligned as it was 11 degrees out
4. Changed cracked vacuum hoses
5. Repositioned brake sensor switch, checked wires
6. Changed Yaw rate sensor and checked for problem with the Latitude sensor beside it and checked all wires
The only thing I haven’t done is check behind the glove box to find the Longitude sensor, it’s an automatic so I assume it must have one ?
All this and the problem still remains, ABS light flashing, large red (!) light flashing and 01486 - System Function Test Activated still on.
Car drives fine and gearbox is ok as well.
Hopefully I haven’t forgotten to mention anything but my head is spinning now.
I’d really appreciate some help with this.
Thanks Dave
This my first time of using this software and I’m more of a DIY mechanic (not on electrics, absolute beginner) so keep suggestions in simple terms please.
Long story short, I purchased this car a week ago with 1 warning light flashing, I checked the basics sensors and rings etc, nothing wrong so I took the car to my mate who plugged his Snap-on machine in, code below.
01542 Yaw rate sensor (G202) electrical problem in circuit
01468 System function test activated
After reading up on that code I thought it strange that the ABS light wasn’t flashing so I decided to take the dials out and investigate, sadly under the black layer with the writing on, the tunnels down to the ABS & EML lights had been filled with black silicone to mask the problems.
So this car has been molested before I purchased it, I’m kicking myself for not noticing but I’m stuck with it now so here goes.
I have changed the sensor (1J0 907 657 B) for a second hand one and since then purchased VCDS-Lite and the results are below.
Code:
VCDS-Lite Version: Release 1.2
Monday, 03 October 2016, 22:24:53:523
Chassis Type: 8L - Audi A3/S3
Scan: 01,02,03,08,15,16,17,22,35,37,45,55,56,57,75,76
-------------------------------------------------------------------------------
Address 01: Engine Labels: 06A-906-032-AUM.LBL
Controller: 06A 906 032 HL
Component: 1.8L R4/5VT 0001
Coding: 11530
Shop #: WSC 00186
VCID: 6F9152B43E85
WAUZZZ8L02A002535 AUZ5Z0A6024009
No fault code found.
Readiness: 0000 0000
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 01M-927-733.LBL
Controller: 01M 927 733 JJ
Component: AG4 Getriebe 01M 4827
Coding: 00000
Shop #: WSC 00000
VCID: 8175840C9811
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: None
Controller: 1C0 907 379 E
Component: ESP FRONT MK60 0104
Coding: 0000000
Shop #: WSC 80093
VCID: 2C2B85B8CF13
1 Fault Found:
01486 - System Function Test Activated
000 - -
-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: Redir Fail!
Controller: 8L0 820 043 K
Component: A3 KLIMAAUTOMAT 0105
Coding: 00041
Shop #: WSC 06435
VCID: 301391C8E33B
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 8L0-959-655-AI8.LBL
Controller: 8L0 959 655 J
Component: Airbag Front+Seite 5008
Coding: 01104
Shop #: WSC 06435
VCID: 45FDD01C4CB9
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments Labels: 8L0-920-xxx-17.LBL
Controller: 8L0 920 980 P
Component: KOMBI+WEGFAHRS. M73 D07
Coding: 00444
Shop #: WSC 00319
VCID: 40F3C108539B
WAUZZZ8L02A002535 AUZ5Z0A6024009
No fault code found.
-------------------------------------------------------------------------------
Address 35: Centr. Locks Labels: 8D0-862-257.LBL
Controller: 8D0 862 257 E
Component: CV-Pump, Alarm, RC D17
Coding: 15178
Shop #: WSC 06435
VCID: 2F1192B4FE05
6 Faults Found:
01371 - Alarm triggered by Door Contact Switch; Driver's Side
35-00 - -
01374 - Alarm triggered by Terminal 15
35-00 - -
01370 - Alarm triggered by Interior Monitoring
35-00 - -
01369 - Alarm triggered by Hood Switch
35-00 - -
00955 - Key 1
09-00 - Adaptation Limit Surpassed
01134 - Alarm Horn (H12)
49-10 - No Communications - Intermittent
-------------------------------------------------------------------------------
Address 45: Inter. Monitor Labels: 4B0-951-173.LBL
Controller: 4B0 951 173
Component: Innenraumueberw. D03
Coding: 00001
Shop #: WSC 00000
VCID: E0B3A188735B
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio Labels: 8D0-035-1xx-56.LBL
Controller: 8L0 035 195 H
Component: symphony II NP2 0005
Coding: 00201
Shop #: WSC 06435
VCID: 33199EC4122D
No fault code found.
End --------------------------------------------------------------------------------------------------
I have noticed that the ABS & Auto trans units have no coding ?
What I have done to try and fix the problem:
1. Basic settings, everything checks out ok except “ERROR not available” in group 069 and also on measuring block 006
2. Coding ABS unit to no avail, labels below if anyone can tell me what codes I should be using
3. Tracking aligned as it was 11 degrees out
4. Changed cracked vacuum hoses
5. Repositioned brake sensor switch, checked wires
6. Changed Yaw rate sensor and checked for problem with the Latitude sensor beside it and checked all wires
The only thing I haven’t done is check behind the glove box to find the Longitude sensor, it’s an automatic so I assume it must have one ?
All this and the problem still remains, ABS light flashing, large red (!) light flashing and 01486 - System Function Test Activated still on.
Car drives fine and gearbox is ok as well.
Hopefully I haven’t forgotten to mention anything but my head is spinning now.
I’d really appreciate some help with this.
Thanks Dave
Last edited: