fault code audi A3/s3

John ler · Aug 27, 2016

hi guy I had a thread a few weeks ago, and need a little if possible, I have had problems with a airbag fault showing on my car, I bought a new airbag ecu, but found out by a forum member that I may have been given a wrong part number from audi, so I have now bought a second hand unit from same car age etc, so I'm sure this is the right one for my car, I now don't have 2 faults I had when fitting the new unit, so I'm quite sure its right, part numbers are all the same, I am show one fault on the air bags and could do with somone pointing me in the right direction to sorting it, also a little help with other fault codes would be a big help, many thanks again guys

Code:

Chassis Type: 8P (1K0)
Scan: 01 02 03 08 09 15 16 17 19 22 25 2E 37 42 44 46 47 52 55 56
          77

VIN: WAUZZ

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: OK 0000
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: Malfunction 0010
22-AWD -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
2E-Media Player 3 -- Status: Not registered 0001
37-Navigation -- Status: Malfunction 0010
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: Malfunction 0010
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: Cannot be reached 1100
52-Door Elect, Pass. -- Status: Malfunction 0010
55-Headlight Range -- Status: Malfunction 0010
56-Radio -- Status: Malfunction 0010
77-Telephone -- Status: OK 0000
 
-------------------------------------------------------------------------------
Address 01: Engine (CDL)       Labels: 06F-907-115-CDL.clb
   Part No SW: 8P0 907 115 AP    HW: 8P0 907 115 B
   Component: 2.0l R4/4V TFSI     0010  
   Revision: 5BH19---    Serial number: AUX7Z0J2FNC0JK
   Coding: 0103000C1C0F0060
   Shop #: WSC 00024 000 00000
   VCID: 0005980453952F42A0-8054

No fault code found.
Readiness: 0110 0001

-------------------------------------------------------------------------------
Address 02: Auto Trans        Labels: 02E-927-770.clb
   Part No SW: 02E 300 012 N    HW: 02E 927 770 AL
   Component: GSG DSG AG6     511 2115  
   Revision:    51112    Serial number: 00001003050064
   Coding: 0000020
   Shop #: WSC 06314 000 00000
   VCID: 1B3FCF68DA33EC9A55-804E

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104)       Labels: 1K0-907-379-60EC1F.clb
   Part No SW: 1K0 907 379 AJ    HW: 1K0 907 379 AJ
   Component: ESP MK60EC1   H30 0107  
   Revision: 00H30001    
   Coding: 11428012092700FB880E01ED90220081390000
   Shop #: WSC 06314 123 12345
   VCID: 7AF1EAECF5497592EE-802E

No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC        Labels: 8P0-820-043.lbl
   Part No SW: 8P0 820 043 BN    HW: 8P0 820 043 BN
   Component: KlimavollautomatH09 0180  
   Revision: 000214      Serial number: 8P0820043BN   
   Shop #: WSC 00000 000 00000
   VCID: 79F3F5E0304F7E8AE7-802C

3 Faults Found:
01856 - Temperature Sensor for Heated Seat; Front Right (G345) 
            010 - Open or Short to Plus - Intermittent
             Freeze Frame:
                    Fault Status: 00101010
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 132
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.11
                    Time: 02:43:32

             Freeze Frame:
                    Temperature: 27.5°C

00532 - Supply Voltage B+ 
            002 - Lower Limit Exceeded - Intermittent
             Freeze Frame:
                    Fault Status: 00100010
                    Fault Priority: 1
                    Fault Frequency: 2
                    Reset counter: 132
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.11
                    Time: 03:29:35

             Freeze Frame:
                    Voltage: 8.60 V

01854 - Heated Seat; Front Right (Z46) 
            012 - Electrical Fault in Circuit - Intermittent
             Freeze Frame:
                    Fault Status: 00101100
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 132
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.11
                    Time: 02:43:34

             Freeze Frame:
                    Temperature: 27.0°C


-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519)       Labels: 8P0-907-063.clb
   Part No SW: 8P0 907 063 A    HW: 8P0 907 063 A
   Component: BCM PQ35  M   105 0575  
   Revision: 00105 AK    
   Coding: 06000B2FB005F200207241E00000094C431E25AA204DD929E40008840040
   Shop #: WSC 06314 123 12345
   VCID: 326102CC6DB94DD266-8066

   Subsystem 1 - Part No SW: 8P2 955 119 F    HW: 8P2 955 119 F  Labels: 1KX-955-119.CLB
   Component: Wischer AU350  H11 0050 
   Coding: 00DD13

   Subsystem 2 - Part No: 8P0 951 177 
   Component: Innenraumuebe  H04 0020 

   Subsystem 3 - Part No: 1K0 951 605 C
   Component: LIN BACKUP HO  H05 1501 

   Subsystem 4 - Part No: 1K0 907 719 C
   Component: Neigungssenso  005 0003 

1 Fault Found:
01134 - Alarm Horn (H12) 
            000 -  - 
             Freeze Frame:
                    Fault Status: 01100000
                    Fault Priority: 4
                    Fault Frequency: 1
                    Reset counter: 92
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.23
                    Time: 00:23:19

             Freeze Frame:
                        Term 15 On
                    Voltage: 14.15 V
                        ON
                        ON
                        Term 50 Off
                        OFF
                        OFF


-------------------------------------------------------------------------------
Address 15: Airbags (J234)       Labels: 8P0-959-655-10.clb
   Part No SW: 8P0 959 655 S    HW: 8P0 959 655 S
   Component: Airbag AU1042 H09 0250  
   Revision: --------    Serial number: 003JU004NSS6
   Coding: 303142413039303030384A55305238503053
   Shop #: WSC 06314 000 00000
   ASAM Dataset: EV_Airba10AURB4 001001
   ROD: EV_Airba10AURB4.rod
   VCID: 52A1624C05796DD246-8006

   Crash sensor for side airbag: driver side: 
   Serial number: 34928RB4000056DDD0C1

   Crash sensor for side airbag: front passenger side: 
   Serial number: 35028RB4000056DEEA4/

   Crash sensor for side airbag: rear: driver side: 
   Serial number: 35128RB4000056DDD34W

   Crash sensor for side airbag: rear: passenger side: 
   Serial number: 35228RB4000056DEEFFF

   Crash sensor for front airbag: driver side: 
   Serial number: 35547RB4000057B42AEX

   Crash sensor for front airbag: front passenger side: 
   Serial number: 35647RB4000057B432DQ

1 Fault Found:
9438490 - Igniter for Driver head airbag 
             B1005 54 [137] - Missing Calibration / Basic Setting
          MIL ON - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Mileage: 60694 km
                    Date: 2015.02.23
                    Time: 00:22:03


-------------------------------------------------------------------------------
Address 16: Steering wheel        Labels: 8P0-953-549.lbl
   Part No SW: 8P0 953 549 K    HW: 8P0 953 549 K
   Component: J0527           H37 0070  
   Coding: 0012112
   Shop #: WSC 06314 000 00000
   VCID: 46894E1C3131C172DA-8012

   Subsystem 1 - Part No: XXXXXXXXXXX 
   Component: E0221           H06 0030

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments        Labels: 8P0-920-xxx-17-MY8.clb
   Part No SW: 8P0 920 983 A    HW: 8P0 920 983 A
   Component: KOMBIINSTR. VDO H04 0150  
   Revision: D0H04003    Serial number: 2243L003000800
   Coding: 0257428
   Shop #: WSC 00762 210 97024
   VCID: 387530E44BC5A78258-806C

2 Faults Found:
00771 - Fuel Level Sensor (G) 
            007 - Short to Ground
             Freeze Frame:
                    Fault Status: 01100111
                    Fault Priority: 7
                    Fault Frequency: 1
                    Reset counter: 92
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.23
                    Time: 00:21:58

00771 - Fuel Level Sensor (G) 
            014 - Defective
             Freeze Frame:
                    Fault Status: 01101110
                    Fault Priority: 7
                    Fault Frequency: 1
                    Reset counter: 92
                    Mileage: 60694 km
                    Time Indication: 0
                    Date: 2015.02.23
                    Time: 00:21:58


-------------------------------------------------------------------------------
Address 19: CAN Gateway        Labels: 1K0-907-530-V4.clb
   Part No SW: 1K0 907 530 AD    HW: 1K0 907 951 
   Component: J533  Gateway   H16 0233

John ler · Aug 30, 2016

Anyone , bump

Dutchie · Aug 30, 2016

preform a basic setting

Uwe · Aug 30, 2016

Dutchie said:
preform a basic setting

Seems like good advice, but I don't think we have a procedure for that at present.

-Uwe-

John ler · Aug 31, 2016

Thanks, I've clicked on it, but there's nothing there, like if doing that on another unit, didn't have this fault in first place until, I disconnected each airbag to eliminate each airbag as afault, now can't get rid, thanks for the input again

John ler · Sep 17, 2016

Guys I really need some help, I'm struggling to clear this fault, a little up date, I have drivers side roof airbag saying too high , I've tried and diffrent roof airbag ( I take roof airbag is curtain airbag) tried that still got the fault, tried a diffrent airbag module still got fault tried taking out the 2 pins at the module connector block and connecting the new air bag direct into 2 pins that are plugged straight into the module block , to see if this will eliminate bad wires running to the rear of the car, but still got fault, can anyone please help me, maybe if someone can point me in the right direction to find the pin read out for the airbag module so I can see if there is possible a diffrent wire that could be damaged somewhere, the 2 wires I have tried are the same 2 wires that are at the rear of the car plugged into the curtain airbag, dose anyone no if these are the only wires that could cause this fault, I'm 100% airbag modules are fine and same on the 2 curtain airbags I have , please can someone help me, I just don't no what to do now, thanks

MartinsX · Sep 17, 2016

If You could provide VIN of Your car, probably someone could trace down original equipment set of Your car and give some advice of airbag module coding.

John ler · Sep 17, 2016

I've got the original module from the car part number ( 8p0 959 655p)
Chassis number thought it was on the scan (
VIN: WAUZZZ8P79A079027 )
I'm total stuffed with it, could coding it make a difference to a fault head airbag, ,,what dose it mean when it says too high and not too low,
I'll put another scan up tomorrow , it would complete tonight for some reason, got stuck loading last or end of scan so couldn't complete so I could put fresh atoms scan up

Dutchie · Sep 17, 2016

A ressistance high means that a airbag module (not the ECU it self) has a internalfault. Please remove the airbag that is suspected of beeing faulty and place a 2.2ohms resistor, deleted all the dtc and recheck.

Please, do know, if you dont know what you are doing with airbag's you can get your self killed!

If the DTC reapears then disconnect the suspect airbag connector and check the resistance measurd by the ECU. It shut be 0. If yes, reconnect and check what it says. It shut be around 2.2ish

Please report findings here

John ler · Sep 17, 2016

Thanks for reply,
Hi I think I'm referring sometimes to ecu, because I've been told in the past it's an ecu, I've taken the airbag off in question and put a 3ohm resister across , but still had the fault, bought a used airbag and tried that, still faults, so took pins out at module and did the same there both with resistor and airbag, but still got the same fault, so bought another module same part no etc, same faults doing the same as before, leaving me to think there must be some other wire fault other than the.2 wires that go the the airbag in question, so really puzzled , I've disconnected battery when doing all this , thanks

Dutchie · Sep 17, 2016

Make the car stock again, old ECU, old airbag module and check in the mvb the resistance. Please post those here

MartinsX · Sep 17, 2016

What fault codes have You got now?

themadscientist · Sep 17, 2016

Have you measured resistance from the airbag connector in question to the main airbag module connector? Did you verify the soft coding is the same between the original module and the one you have now?

Last but not least, the airbag connectors are known to have crappy connections on Audi/VW vehicles, leading to high resistance codes. Stabilant will help if that's the case.

John ler · Sep 19, 2016

Do you mean measure the resistance one the wires with both airbag and module disconnected , I allways thought you could do this this module connected, I've done it with the airbag connected then disconnected and then with a 2.2 ohm resister fitted , but can't find the reading to hand at the moment, think I had resistance high with bag on, 0.4 without bag one and with 2.2 ohm resister something like 3-5 ohm's but not 100% sure on them and if it was a 2.2 ohm 1/2 watt resister, all dome throu vcds I don't have a multi meter to try with out doing it thro vcds, I've never removed the engine bay ecu from the car and I've tired 3 airbag modules 2 with same part number and 1 that is meant to be supper seading to the first 2, I've tired copying the code from the original one from the car but the other 2 will not accept the coding, but I think I'm going to be stuck here, especially with the coding and possibly made a rod for my own back here, but somehow there must be a way around this, when I bought the car, it was left hand drive and had , had a light fire to the loom above the airbag module , so I fitted a second hand wire loom from a 2012 car that had other extra thing to it, only things like sat nav and Bose sounds, but the loom was from a diffrent car, I didn't see much harm in doing this, thinking the only changes would be like the spec of the car I've like the nav Bose and didn't for one minuet think there could be any difference between the airbags, the 2012 had only the same airbags as mine no extra one's , and only 11 months from build dates, I no that isn't the point, so I do not think I have a chance in finding the new loom coding for the airbags, I personally don't mind if the drives side head airbag doesn't work, buy one day I will sell and there's no way I can live with just not telling someone about it, in case they had some sort of accident and the curtain airbag should have gone off and someone was hurt, this just isn't me, I've seen cars with nothing left of them where airbags haven't gone off, but also in the our country the airbag light can not be lit up, and this is the main thing , mine is, is there any way of figuring this out so everything works , could anyone exsplain to me what part of the coding make each car individual to each car, many thanks for your help, I don't mind paying is there was someone close to me to sort this out, but I think everyone on here are over sea's to me, pleas help me out guys, and don't give up on telling me what you think I should try,also would a 3.3 ohm's resister be to high to try their resister in the wiring end of the bag come for, I bought 2 and I'm shore one was 2.2 1/2 watt and other 3.3 1/2 watt resisters, thanks again

Code is

1 Fault Found:
9438490 - Igniter for Driver head airbag
B1005 54 [137] - Missing Calibration / Basic Setting
MIL ON - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Mileage: 60694 km
Date: 201

Dutchie · Sep 19, 2016

Not to be aan grammer nazi, but can you ad some white space, now and then in that huge part of text&#55357;&#56837;

John ler · Sep 19, 2016

Sorry sat on the loooo on my mobile phone while texting that, with fat fingers and small digits ,

John ler · Sep 20, 2016

Can anyone tell me if the watt part on the resister makes any diffracted, I have no idea, was told 1/4 of a watt but could only get 1/2 watt , thanks

I've found the chassis number from the car the wire loom came from, not sure if anyone would be able to find out airbag module and coding from this car,
WAUZZZ8P7CA154302
Would this help, have I basically made my car now this one, ??

PetrolDave · Sep 20, 2016

John ler said:
Can anyone tell me if the watt part on the resister makes any diffracted, I have no idea, was told 1/4 of a watt but could only get 1/2 watt , thanks

The watt rating of a resistor tells how much heat it can handle without burning out.

A quick way to work out the watt rating you need on a 12V electrical system (i.e. most cars) is to divide 144 by the resistor value in ohms. Provided the resistor watt rating is higher than that number it shouldn't burn out - BUT it may still get hot (hot enough to burn things or people) so take care!

P.S. 144 is 12 squared - the power is calculated by voltage squared divided by resistance.

MartinsX · Sep 20, 2016

Do You think he will test airbag system in deployment mode?

Even 1/8W is enough. Resistance must be correct.

Uwe · Sep 20, 2016

MartinsX said:
Do You think he will test airbag system in deployment mode? Even 1/8W is enough. Resistance must be correct.

If you use 1/8 watt and airbags do deploy, resistor WILL ignite. :eek:

-Uwe-

fault code audi A3/s3

Verified VCDS User

Verified VCDS User

Verified VCDS User

Benevolent Dictator

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Verified VCDS User

Benevolent Dictator