Page 6 of 6 FirstFirst ... 456
Results 51 to 58 of 58

Thread: Misfire after aborted scan, ECU comm problems, 2005 S4 Cabriolet b6 8H BHF 4.2 V8

  1. #51
    Verified VCDS User
    Join Date
    Aug 2016
    Location
    USA
    Posts
    26
    Post Thanks / Like
    Re the BHF engine – yes, Jack, I can see that…we did buy this car eyes wide open, knowing that the engine would have to come out some day. Tell me about the non synthetic oil comment, is it because of sludge? I use Mobil1 0w40 currently, I am open to suggestion.

    The bank one exhaust cam is 15 degrees different, behind the other three cams. Coincidentally, the sprocket has 25 teeth…one tooth is 14.4 degrees.

    I used Snap-On MT 324 leakdown tester with 110 PSI source 9-18-2016. Engine was cold, as it is torn apart right now. All cylinders were within 8% - #1 10%, #5 5%, #4 10%, #8 10%, #6 13%, #3 8%, #7 10%, #2 8%.

    I noticed that some cylinders held at 20-30% leakage for a few seconds, then dropped for final reading – is that normal? I zeroed the tester between each cylinder. It appeared to have at least 3-4% deadband, so I zeroed it in the same regulator direction each time.

    Next up – drop the oil pan to look for sludge (and tensioner pieces) and to check the strainer per ivagp’s suggestions. The crank is locked in place for cam adjustment. When the engine is back together, I have an oil pressure test kit ready.

    I am also refinishing the valve covers – there was big time corrosion. When I media blasted, what was black became deep ruts. It appeared to have a zinc chromate, yellow / green primer, strange choice. Is that factory?

    Thanks All.

  2. #52
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,165
    Post Thanks / Like
    zinc chromate, yellow / green primer, strange choice. Is that factory?
    Was the prior owner an A&P or in aviation/military?

    Not OEM.......

    http://forums.ross-tech.com/showthread.php?2224-Oil
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  3. #53
    Verified VCDS User
    Join Date
    Aug 2016
    Location
    USA
    Posts
    26
    Post Thanks / Like
    Quote Originally Posted by Jack@European_Parts View Post
    Was the prior owner an A&P or in aviation/military?
    Unknown to me. The car had a few owners.
    Interesting oil thread. Yes, the oil gets very, very hot - the entire area underhood seems to be far hotter than most cars.

    By the way, does anyone know of a self study manual for the BHF 4.2 liter engine? And how to get one?

    Thanks, all.

  4. #54
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,165
    Post Thanks / Like
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  5. #55
    Verified VCDS User
    Join Date
    Aug 2016
    Location
    USA
    Posts
    26
    Post Thanks / Like
    well, Houston, a problem...the OEM exhaust cam bolt I ordered from ECS was 125mm long...and has visible runout. The one that came out of the cam was 100 mm long. The ECS bolt does not wind in far enough. The good news is that I think the procedure will work with the right part. Still researching part numbers tonight, off to the dealer tomorrow.
    Last edited by RichS; 09-19-2016 at 10:04 PM. Reason: I made a mistake.

  6. #56
    Verified VCDS User
    Join Date
    Aug 2016
    Location
    USA
    Posts
    26
    Post Thanks / Like
    Greatly appreciated Jack - is there a self study manual that is specific to the MPI, BHF engine? Or is the FSI engine as close as we get?

  7. #57
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,165
    Post Thanks / Like
    Search around ............
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  8. #58
    Verified VCDS User
    Join Date
    Aug 2016
    Location
    USA
    Posts
    26
    Post Thanks / Like
    And in conclusion - the car went back together well, and runs better than ever. The difference in power and smoothness is significant. No sludge present that I can find. No chain rattle, hot or cold. I also had to replace the center radiator, PRG valve, and repair various vacuum leaks. Currently, there are no engine error codes or misfires at all.

    I still have to reprogram a new passenger seat controller, and figure out why the passenger side window does not always drop automatically on door opening - but hey, the car runs well. Lots of interior trim to fix as well.

    Thanks to all that commented. Your comments pushed me to figure out what was really going on here, and gave me the courage to pull it all apart. I took almost all of your suggestions.

    After owner research, I may yet pull the engine. Regardless, I am watching carefully for any sign of chain rattle or misfire, and stepping up my oil change frequency. It appears someone has already removed the engine valley plate, perhaps for check valves, so I am researching that. We anticipate enjoying this car a long time. I won't fear taking the engine out thanks to this experience and your collective insight. Next up - oil pressure test, at some point timing chain tensioner service and perhaps valve stem seals if not heads.

    Regards,
    Rich

  9. Likes jyoung8607, Uwe, Jack@European_Parts liked this post

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •