Page 5 of 5 FirstFirst ... 345
Results 41 to 48 of 48

Thread: Updated to Release 19.6 and Having Trouble? Read This Thread

  1. #41
    VCDS Distributor Mike@Gendan's Avatar
    Join Date
    Jun 2014
    Location
    Swansea, UK
    Posts
    410
    Post Thanks / Like
    Quote Originally Posted by Andy View Post
    ....
    4) Start up VCDS (it may have already started at the end of the installation, which is fine). If VCDS won't start up at all after updating, make sure that Zone Alarm or your virus scanner are not blocking/quarantining the file. Make sure it says Release 18.9 at the top of the screen. If says an older version then something didn't go right. Check the shortcut on your desktop to make sure it's for Release 19.6. If needed, exit out of VCDS then repeat steps 1-3.
    ...
    I'm guessing that should be 19.6 now?
    Apparently I should put something witty or profound in here...

  2. Likes Uwe liked this post
  3. #42
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    23,870
    Post Thanks / Like
    Blog Entries
    1
    Quote Originally Posted by Mike@Gendan View Post
    I'm guessing that should be 19.6 now?
    Fixed it for him.

    -Uwe-
    The engineering problems are likely insurmountable. It would be like proposing to land a rocket booster section on a barge floating in the middle of the ocean.

  4. Likes Mike@Gendan, Andy liked this post
  5. #43
    Verified VCDS User bobbik's Avatar
    Join Date
    Oct 2015
    Location
    Poland
    Posts
    19
    Post Thanks / Like
    Code:
    Thursday,18,July,2019,11:33:50:22340
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows XP x86
    VCDS Version: 19.6.1.0
    Data version: 20190529 DS308.0
    www.Ross-Tech.com
    
    Workshop Code: 000 11618 000000
    
    
    
    
    --------------------------------------------------------------------------------
    --------------------------------------------------------------------------------
    
    
    Gateway Installation List:  3Q0 907 530 L
    
    01-Engine -- Status: Malfunction 0010
    02-Auto Trans -- Status: Malfunction 0010
    03-ABS Brakes -- Status: Malfunction 0010
    05-Acc/Start Auth. -- Status: Malfunction 0010
    08-Auto HVAC -- Status: Malfunction 0010
    09-Cent. Elect. -- Status: Malfunction 0010
    13-Auto Dist. Reg -- Status: Malfunction 0010
    15-Airbags -- Status: Malfunction 0010
    16-Steering wheel -- Status: Malfunction 0010
    17-Instruments -- Status: Malfunction 0010
    19-CAN Gateway -- Status: Malfunction 0010
    2B-Steer. Col. Lock -- Status: Malfunction 0010
    3C-Lane Change -- Status: Cannot be reached 0100
    42-Door Elect, Driver -- Status: Malfunction 0010
    44-Steering Assist -- Status: Malfunction 0010
    4B-Multifunc. Module -- Status: INTERFACE NOT COMPATIBLE 
    52-Door Elect, Pass. -- Status: Malfunction 0010
    5F-Information Electr. -- Status: Malfunction 0010
    6C-Back-up Cam. -- Status: OK 0000
    75-Telematics -- Status: Malfunction 0010
    CA-Sunroof -- Status: INTERFACE NOT COMPATIBLE 
    D8-LED HeadL. Pwr Left -- Status: INTERFACE NOT COMPATIBLE 
    D9-LED HeadL. Pwr Right -- Status: INTERFACE NOT COMPATIBLE
    Does it mean my interface is too obsolete?

  6. #44
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    23,870
    Post Thanks / Like
    Blog Entries
    1
    Quote Originally Posted by bobbik View Post
    Does it mean my interface is too obsolete?
    There are at least four control modules in that car that your "legacy" interface can't communicate with. So yes, an interface upgrade would be recommended.

    -Uwe-
    The engineering problems are likely insurmountable. It would be like proposing to land a rocket booster section on a barge floating in the middle of the ocean.

  7. Likes Eric liked this post
  8. #45
    Verified VCDS User
    Join Date
    Apr 2017
    Location
    India
    Posts
    2
    Post Thanks / Like
    Hi,

    Recently, I had upgraded to a new laptop that runs Windows 10 64 bit version. I installed VCDS version 19.6.1. When I launch VCDS from desktop shortcut, the program does not launch. Following are the checks I have performed.

    1. When I check the task manager, the program is not listed in the processes.
    2. Tried running the program in Administrator mode.
    3. Tried troubleshooting compatibility issues and ran in Win8 and Win7 compatibility modes.
    4. Checked that firewall has been configured to allow VCDS.
    5. Added VCDS.exe as an exception in the antivirus software.

    None of these work. Any pointers to what could be the problem?

    Thanks in advance.

    Edit: I have the Hex-V2 interface with a 3-VIN license.

  9. #46
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    23,870
    Post Thanks / Like
    Blog Entries
    1
    Quote Originally Posted by graaja View Post
    Recently, I had upgraded to a new laptop that runs Windows 10 64 bit version. I installed VCDS version 19.6.1. When I launch VCDS from desktop shortcut, the program does not launch.
    At this point, I think there are more people running Windows 10 and the x64 version of VCDS than any other combination, so there has to be something peculiar about your computer.

    Try the "Install 32-bit EXE on 64-bit System" option in the installer to see if that helps.

    If that still doesn't work, I would suggest uninstalling and and all bloatware and nannyware that came pre-installed on this computer.

    -Uwe-
    The engineering problems are likely insurmountable. It would be like proposing to land a rocket booster section on a barge floating in the middle of the ocean.

  10. #47
    Verified VCDS User
    Join Date
    Apr 2017
    Location
    India
    Posts
    2
    Post Thanks / Like
    Quote Originally Posted by Uwe View Post
    Try the "Install 32-bit EXE on 64-bit System" option in the installer to see if that helps.
    That solved the problem. VCDS now works.

    Thanks a lot for the solution.

  11. Likes Uwe, Andy, PetrolDave liked this post
  12. #48
    Verified VCDS User
    Join Date
    Aug 2019
    Location
    Russia
    Posts
    1
    Post Thanks / Like

    Possible bug?

    Hello!
    I have a problem with latest version of VCDS (19.6.1). When I try to access some of control modules of my car (for example, ABS and steering angle sensor), the error balloon above "Advanced ID" button is shown: "Vehicle is unsupported". Every other button stays disabled.
    I know about legacy interfaces and 2019+ cars... BUT! My car is 2013 Polo sedan (russian market model), my interface is HEX-USB+CAN, OS is Windows 10 x64. When I've reinstalled previous version (19.6.0 - thank God I kept distro) - all work fine again.
    Here is the log from the "Advanced ID" window (sorry don't know how exactly it's called):
    Code:
    Wednesday,21,August,2019,20:57:06:05202
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
    VCDS Version: 19.6.1.0 (x64)
    Data version: 20190529 DS308.0
    www.Ross-Tech.com
    
    
    
    
    
    --------------------------------------------------------------------------------
    --------------------------------------------------------------------------------
    
    
                    Address 03: ABS Brakes
    Control Module Part Number: 6R0 907 379 AQ
      Component and/or Version: ABS9.0 front  H01 0003
               Software Coding: 50DD2F64212504C10A18F472845720000000
                Work Shop Code: WSC 01530
                          VCID: 0D115EF2DC450C27E2-8058
    
    Advanced Identification/FAZIT
         Serial number: --------------
         Identification: BPA-085
         Date: 08.08.13
         Manufacturer number: 0040
         Test stand number: 2660
    Flash Status
         Programming Attempts(application): 1/0
         Flash Date: 00.01.01
    Misc.
         Hardware number: 6R0 907 379 AQ
         Workshop System Name: J104
         ASAM Dataset: EV_Brake1ABS90BOSCH
         ASAM Dataset Revision: 003017
    VCDS Info:
           VCID: 0D115EF2DC450C27E2-8058
           Labels: Redir Fail!
           ROD: ERROR - EV_Brake1ABS90BOSCH 003017 (VN75)
    Of course, I will post full scan if needed.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •