polo 6R power steering problem

Status
Not open for further replies.
   #1  

MUROGIS

Pirate
Walking the Plank
Joined
Jan 4, 2016
Messages
5
Reaction score
0
Location
Lithuania
Hello. Please help. I have changed power steering module 6r423156. Replaised with new TRW JER162. Now i have a fault 816.(Power Steering Sensor (G250): Open or Short to Plus ). But there no are sensor in steering column. Like I understand I have to change coding, but I need to login and I do not know the code and what parameters to change.
Am I right ? Can anyone help ?
 
   #2  

DrPeter

Ross-Tech Employee
Ross-Tech Employee
Joined
Jan 29, 2014
Messages
1,971
Reaction score
3,623
Location
16.4905° S, 151.7375° W
Hello,

If you could post up an Auto-Scan of the vehicle in question, this will help us see the concerns, coding, etc...

In the meantime have a look at this Ross-Tech user manual page for more information about coding, VCDS could have a pop-up for coding options.

And, if you truly have a short to ground, this Ross-Tech form page about testing for short to grounds/positives, etc.. is a good place to start.

Hope this helps,

drpeter
 
  • Like
Reactions: Uwe
   #3  

MUROGIS

Pirate
Walking the Plank
Joined
Jan 4, 2016
Messages
5
Reaction score
0
Location
Lithuania
Code:
Data from pirated copies of VCDS is not welcome here
 
Last edited by a moderator:
   #4  

AIB Wolfgang

VCDS Distributor
VCDS Distributor
Joined
Sep 24, 2014
Messages
368
Reaction score
450
Location
Germany
Hi Murogis,
thats why there is allways the request for complete AUTO-SCAN. VIN to see the PR numbers and out of the scan, what devices are mounted.
maybe you have installed a wrong steering, because G250 must be mounted, after looking in the Repair manual
 
  • Like
Reactions: Uwe
   #5  

MUROGIS

Pirate
Walking the Plank
Joined
Jan 4, 2016
Messages
5
Reaction score
0
Location
Lithuania
Code:
Data from pirated copies of VCDS is not welcome here.
 
Last edited by a moderator:
   #6  

AIB Wolfgang

VCDS Distributor
VCDS Distributor
Joined
Sep 24, 2014
Messages
368
Reaction score
450
Location
Germany
Hello Murogis,
just looked for parts and wiring diagram:)

Correct parts number is 6R1 423 055 K
and on the top, your car is mounted with ABS / ESP and so in the WD the G250 is mounted in the Steering / top of the input shaft.
Think there are some things wrong
 
   #7  

MUROGIS

Pirate
Walking the Plank
Joined
Jan 4, 2016
Messages
5
Reaction score
0
Location
Lithuania
but until I have changed the modul I had not a fault 816.
A modul I have changed because I had a fault in CAN, now it is gone and is only fault 816.
 
   #8  

MUROGIS

Pirate
Walking the Plank
Joined
Jan 4, 2016
Messages
5
Reaction score
0
Location
Lithuania
I find out that my car is with ESP ant there are no sensor G250 at all. There is only sensor G85. But I have a fault with problem in sensor G250.
 
   #9  

AIB Wolfgang

VCDS Distributor
VCDS Distributor
Joined
Sep 24, 2014
Messages
368
Reaction score
450
Location
Germany
As Uwe mentioned:


Code:

Data from pirated copies of VCDS is not welcome here.
 
  • Like
Reactions: Uwe
Status
Not open for further replies.
Back
Top