- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Twelve choices listed for "Assistance light functions"
Last edited by a moderator:
Enable High Beam Assist- 2016 VW GTI- USA w/DAP
- Thread starter bbelhumeur
- Start date
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
Greetings: I attempted the High Beam Assist on my 2016 NAR Golf Sportwagen TSI SEL but ran into an issue when I followed the directions from post #29; it appears that the only option for headlight styles following this is the halogen whereas I have the bi-xenon. I did get the correct sub-menu to pop up in my MMI but each time I attempted to activate it, an error code would be thrown. I included the twelve different options under "Assistance Light Functions". Attempting the "IDE08786-ENG116637-Assistance light functions-Menueesteuerung Fernlichtassistent" will not provide an option for bi-xenon. Any insight would be appreciated!
McSpiffy (Jock?): I'm intrigued by your exercise! My understanding is that the Bi-Xenons for the mk7 come in 3 x separate versions (albeit the last two types physically look the same)
- Bi-xenon headlights
- Bi-xenon headlights with dynamic cornering light (AFS)
- Bi-xenon with dynamic light assist (DLA)
According to an earlier version of your autoscan, Btye 2 of the BCM was hex1A - so the pertinent Bits for the headlight functions was hex2 (i.e 010). This means according to the new "yellow" screens on the latest RT software, Xenon_AFS. This strongly suggests that your vehicle has the 2nd headlight fittings in the list above.
Your latest autoscan has Byte 2 = hex1B - therefore Bits0-2 are hex3 (i.e. 011), which means Xenon_AFS_and_main_beam_assist. So the BCM now thinks that it has to support the last headlight fitting in the list above.
According to VW:
The layout of the bulbs and the appearance of the bixenon
headlight with advanced frontlighting system
(AFS) and dynamic main beam control (MDF) is the
same as that of the bi-xenon headlight with AFS.
The design of the inside of this bi-xenon headlight is,
however, different. It features a group of individually
moveable screens which can be swivelled into the
light cone cast by the main beam lamp.
The dynamic main beam control function, that is, the
partial masking of certain areas of illumination, is
implemented through a combination of the screens
and the horizontal adjustment of the module.
headlight with advanced frontlighting system
(AFS) and dynamic main beam control (MDF) is the
same as that of the bi-xenon headlight with AFS.
The design of the inside of this bi-xenon headlight is,
however, different. It features a group of individually
moveable screens which can be swivelled into the
light cone cast by the main beam lamp.
The dynamic main beam control function, that is, the
partial masking of certain areas of illumination, is
implemented through a combination of the screens
and the horizontal adjustment of the module.
So herein lies my confusion - if the "innards" of the MDF version of the bi-xenon headlights are different to the version in your car, changing the BCM code to operate main-beam-assist would appear to be inherently problematic.
Or have I missed something - entirely likely?
Don
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Don, thanks for the prompt reply!
I didn't see an option for bi-xenon, only the standard lamps. I'm wondering if I should pick one of the eleven other options under "Assistance Light Functions" to see if the bi-xenon is there.
The only difference between my earlier and latest autoscan is my resetting of the original parameters and removing any error codes.
What are the new "yellow" screens you refer to in the latest RT software?
Thanks again and I look forward to your reply!
P.S. The McSpiffy derives from an adult Scouting program (WoodBadge); we were the Beaver Patrol and each of us had to personalize our mascot as a signature. Since I bagpiped, I had a bagpiping beaver as my signature (kinda like McSquizzy from the animated movie "Open Season") http://openseason.wikia.com/wiki/File:Quizzy3.jpg
I didn't see an option for bi-xenon, only the standard lamps. I'm wondering if I should pick one of the eleven other options under "Assistance Light Functions" to see if the bi-xenon is there.
The only difference between my earlier and latest autoscan is my resetting of the original parameters and removing any error codes.
What are the new "yellow" screens you refer to in the latest RT software?
Thanks again and I look forward to your reply!
P.S. The McSpiffy derives from an adult Scouting program (WoodBadge); we were the Beaver Patrol and each of us had to personalize our mascot as a signature. Since I bagpiped, I had a bagpiping beaver as my signature (kinda like McSquizzy from the animated movie "Open Season") http://openseason.wikia.com/wiki/File:Quizzy3.jpg
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
McSpiffy: The yellow screens are described HERE - but as Uwe has confirmed, only available to the HEX series products
Here's the options under Byte 2, Bits 0-2 (from another cable)
No Function=hex0
Basic_FLA=hex1
AFS,BCM-Highbeam=hex2
AFS,FLA,BCM-Highbeam=hex3
AFS,Highbeam+ueber AFS=hex4
AFS, FLA Highbeam+ueber AFS=hex5
AFS,FLA_High_beam(GLW,MDF)= hex6
And here's the VCDS "yellow" screen:
AFS, (Advanced Frontlighting System)-dynamic cornering light (Initialism for the cornering light CAN bus)
FLA (Main beam assist) Assistance system which supports the driver when changing from main beam to low beam headlights, in order to prevent dazzling other road users
Don
PS: And in the words of Bayden Powell ............DYB DYB DYB (DOB?)!!!
Last edited:
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Surprise! More issues!!! High beam assist not working + tons more DTCs
Greetings:
So i thought my troubles were over after clearing the previous DTCs and restoring the car back to the previous coding (pre-Enable High Beam Assist efforts). Much to my chagrin, I still receive an error message when I first click on my high beams, even though there is no longer an option for High Beam Assist in the MMI. I put 1000 mi. on the car the past few days while traveling to visit my parents who live in NE Arkansas (8 hr trip from Chicago). Needless to say, I still have an issue with the A/C bug (cold air stops and I lose fan control option; however, restarting the car seems to resolve the issue). I did an oil change this evening and decided to run a VCDS scan . . . sixteen status malfunctions!!!! I've never had this many and they all say "missing message". Did I clear out something I wasn't supposed to? The only existing DTC from my previous efforts had to do with the humidity sensor (does anyone know where that is located?). I'm not sure if my headlight coding caused an issue or if it was possibly the detailers whom inadvertently sprayed something where it shouldn't have been . . .
Greetings:
So i thought my troubles were over after clearing the previous DTCs and restoring the car back to the previous coding (pre-Enable High Beam Assist efforts). Much to my chagrin, I still receive an error message when I first click on my high beams, even though there is no longer an option for High Beam Assist in the MMI. I put 1000 mi. on the car the past few days while traveling to visit my parents who live in NE Arkansas (8 hr trip from Chicago). Needless to say, I still have an issue with the A/C bug (cold air stops and I lose fan control option; however, restarting the car seems to resolve the issue). I did an oil change this evening and decided to run a VCDS scan . . . sixteen status malfunctions!!!! I've never had this many and they all say "missing message". Did I clear out something I wasn't supposed to? The only existing DTC from my previous efforts had to do with the humidity sensor (does anyone know where that is located?). I'm not sure if my headlight coding caused an issue or if it was possibly the detailers whom inadvertently sprayed something where it shouldn't have been . . .
Code:
Saturday,01,July,2017,22:38:11:06278
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 17.6.0.2 (x64) HEX-NET CB: 0.4341.4
Data version: 20170602 DS274
www.Ross-Tech.com
VIN: 3VWC17AU4GM501532 License Plate: V93 8607
Mileage: 31994km-19880mi Repair Order: 070117B
Chassis Type: AU (5Q0)
Scan: 01 02 03 05 08 09 10 13 15 16 17 19 2B 3C 42 44 47 52 55 5F
75 A5
VIN: 3VWC17AU4GM501532 Mileage: 31994km-19880miles
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
05-Acc/Start Auth. -- Status: Malfunction 0010
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: Malfunction 0010
13-Auto Dist. Reg -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: Malfunction 0010
2B-Steer. Col. Lock -- Status: Malfunction 0010
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: Malfunction 0010
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: Malfunction 0010
55-Headlight Range -- Status: Malfunction 0010
5F-Information Electr. -- Status: Malfunction 0010
75-Telematics -- Status: Malfunction 0010
A5-Frt Sens. Drv. Assist -- Status: Malfunction 0010
-------------------------------------------------------------------------------
Address 01: Engine
Cannot be reached
-------------------------------------------------------------------------------
Address 02: Auto Trans (J217) Labels: 09G-927-749-V2.clb
Part No SW: 09G 927 749 AP HW: 09G 927 749 AP
Component: AISIN AG6 G3 129 2943
Coding: 010200000C000000000000000000000000000000
Shop #: WSC 00066 790 00221
ASAM Dataset: EV_TCMAQ250031 002009
ROD: EV_TCMAQ250031_002_VW25.rod
VCID: 075E5B89BE35B27F80-8052
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels:. 5Q0-907-379-IPB-V1.clb
Part No SW: 3Q0 907 379 AB HW: 3Q0 907 379 G
Component: ESC H42 0723
Revision: 00000000 Serial number: 61255000000354
Coding: 04FA6AA12420096D007C020381C5292056249000408194B416435052C082
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_Brake1UDSContiMK100IPB 034036
ROD: EV_Brake1UDSContiMK100IPB_034_VW37.rod
VCID: 7AB8327DFDC7DF978F-802E
10 Faults Found:
8246 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
8250 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:02
8252 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
8254 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
8256 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
8258 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 1
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
8264 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
8351 - Databus
U1122 00 [008] - Implausible Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:59
16409 - Display for Tire Pressure Monitoring
C1146 02 [008] - Signal Failure
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:07
16410 - Display for Tire Pressure Monitoring
C1146 02 [008] - Signal Failure
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:07
-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. (J518) Labels:| 5Q0-959-435.clb
Part No SW: 5Q0 959 435 A HW: 5Q0 959 435
Component: VWKESSYMQB 021 0604
Revision: 00021000 Serial number: 0367374266
Coding: 030C0C
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_KessyHellaMQBAB 002011
ROD: EV_KessyHellaMQBAB_002_VW37.rod
VCID: 3A38F27DBD471F97CF-806E
1 Fault Found:
12716804 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5G0-907-044.clb
Part No SW: 5GM 907 044 A HW: 5GM 907 044 A
Component: Climatronic H03 1001
Revision: 00001K01
Coding: 02020024200100000105000012111402
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_ACClimaBHBVW37X 003018
ROD: EV_ACClimaBHBVW37X_003_VW37.rod
VCID: 42C88A9DD597575797-8016
Fresh Air Blower Front:
Refrigerant Pressure And Temperature Sender:
Air quality sensor:
2 Faults Found:
459525 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
459023 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels:| 5Q0-937-08X-MV1.clb
Part No SW: 5Q0 937 087 AA HW: 5Q0 937 087 AA
Component: BCM PQ37BOSCH 028 0162
Revision: -------- Serial number: 86581605150679
Coding: 00511B464041A2E969E44000001407001800000000000000000000000000
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_BodyContrModul1UDSBosc 015002
ROD: EV_BCMBOSCH_015_VW37.rod
VCID: 7AB8327DFDC7DF978F-802E
Control Unit For Wiper Motor:
Subsystem 1 - Part No SW: 5GM 955 119 HW: 5GM 955 119 Labels: 5QX-955-119-V1.CLB
Component: WWS 150430 043 0581
Serial number: 150628095715
Coding: 0E4DDD
Rain Light Recognition Sensor:
Subsystem 2 - Part No SW: 5Q0 955 547 A HW: 5Q0 955 547 A Labels: 5Q0-955-547.CLB
Component: RLHS 037 0059
Serial number: S5Y15M05D11H20M57S08
Coding: 90A8DD
Sun Roof:
Subsystem 3 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J245 PS22.409 H03 0004
Serial number: 0000FST0009CPKU00000
Coding: 191800
Roof Blind:
Subsystem 4 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J394 PS22.409 H03 0004
Serial number: 0000FST0009CQ2D00000
Coding: 191800
Relative Air Humidity Interior Sender:
7 Faults Found:
534549 - Databus
U1121 00 [009] - Missing Message
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 11
Reset counter: 69
Mileage: 30204 km
Date: 2017.06.27
Time: 20:10:25
541973 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
559125 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
555541 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
542229 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
542485 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
329480 - Heated Passenger Seat
B1806 F0 [008] - Safety Shut-Off due to Occupant Detection
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 107
Mileage: 31152 km
Date: 2017.06.30
Time: 10:46:10
-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J791) Labels:| 5Q0-919-298.clb
Part No SW: 5Q0 919 298 K HW: 5Q0 919 298
Component: PARKHILFE PLA H12 0054
Revision: -------- Serial number: 39431513200575
Coding: 0031165011
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_EPHVA2CAU3700000 003021
ROD: EV_EPHVA2CAU3700000_003_VW37.rod
VCID: 47DE9B89FEB5727F40-8012
2 Faults Found:
13637426 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
12648465 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 13: Auto Dist. Reg (J428) Labels:| 5Q0-907-572-V1.clb
Part No SW: 5Q0 907 572 F HW: 5Q0 907 572 D
Component: ACC Bosch MQB H05 0400
Serial number: 13031503210237
Coding: 01045400FE0739
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_ACCMRRBoschVW372 001016
ROD: EV_ACCMRRBoschVW372_VW26.rod
VCID: 3A38F27DBD471F97CF-806E
10 Faults Found:
1066 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
1056 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0276 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0277 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0278 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0279 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
Control Module temperature: 50 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0280 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
0281 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
1050 - Transmission in Limp Mode
P305B 00 [008] - -
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
Control Module temperature: 51 ∞C
Voltage terminal 15: 12.4 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
1043 - Automatic Distance Control
B10E7 F0 [008] - Disconnected
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:59:33
Control Module temperature: 53 ∞C
Voltage terminal 15: 12.2 V
Vehicle speed: 0.00 m/s
Acceleration: 0.00 m/s≤
-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels:| 5Q0-959-655.clb
Part No SW: 5Q0 959 655 J HW: 5Q0 959 655 J
Component: AirbagVW20 009 0825
Serial number: 003GCR01Y1DL
Coding: 8CCCFC00000000005000001AC24800000065
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_AirbaVW20SMEVW37X 002138
ROD: EV_AirbaVW20SMEVW37X_VW37.rod
VCID: 47DE9B89FEB5727F40-8012
Occupant Detection:
Subsystem 1 - Part No SW: 4M0 959 339 B HW: 4M0 959 339 B
Component: BF-Gewichtss. H11 0021
Serial number: IBH0000J1500031ZIL0K
Coding: 303137
Side Sensor Driver Front:
Subsystem 2 - Part No SW: ----------- HW: 480 002 305 15
Component: SideSensor_Df 001 0887
Serial number: 357000000000A560A418
Coding: 2D2D2D
Side Sensor Passenger Front:
Subsystem 3 - Part No SW: ----------- HW: 480 002 205 15
Component: SideSensor_Pf 001 0887
Serial number: 358000000000D0B06418
Coding: 2D2D2D
Side Sensor Driver Rear:
Subsystem 4 - Part No SW: ----------- HW: 480 402 704 15
Component: SideSensor_Dr 001 6149
Serial number: 3510002C91A91E714070
Coding: 2D2D2D
Side Sensor Passenger Rear:
Subsystem 5 - Part No SW: ----------- HW: 480 402 804 15
Component: SideSensor_Pr 001 6149
Serial number: 35200029B1A87872711+
Coding: 2D2D2D
Front Sensor Driver:
Subsystem 6 - Part No SW: ----------- HW: 480 400 505 15
Component: FrontSensor_D 001 6149
Serial number: 3550002AF1A8787292DL
Coding: 2D2D2D
Front Sensor Passenger:
Subsystem 7 - Part No SW: ----------- HW: 480 400 505 15
Component: FrontSensor_P 001 6149
Serial number: 3560002B31A878729376
Coding: 2D2D2D
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel (J527) Labels:| 5Q0-953-549.clb
Part No SW: 5Q0 953 521 BB HW: 5Q0 953 569 A
Component: Lenks.Modul 075 0175
Revision: FF032032 Serial number: 20150328500718
Coding: 0C10
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_SMLSVALEOMQB 001015
ROD: EV_SMLSVALEOMQB_VW37.rod
VCID: 73A61F59DAADAEDFCC-8026
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5G0-920-XXX-17.clb
Part No SW: 5G1 920 840 A HW: 5G1 920 840 A
Component: KOMBI 242 6420
Coding: 0BA4111AED98CF0502886A0B5000000000000000
Shop #: WSC 00066 790 00194
ASAM Dataset: EV_DashBoardVDDMQBAB 009046
ROD: EV_DashBoardVDDMQBAB_009_VW26.rod
VCID: 2502310124F9806F92-8070
2 Faults Found:
16776971 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
16776988 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:| 5Q0-907-530-V1.clb
Part No SW: 5Q0 907 530 AF HW: 5Q0 907 530 M
Component: GW MQB High 212 2223
Revision: -------- Serial number: 22051510000845
Coding: 0901000830085900FB00021A1C0F00000001050000000000000000000000
Shop #: WSC 00066 790 00194
ASAM Dataset: EV_GatewConti 013020
ROD: EV_GatewConti_013_VW37.rod
VCID: 75A22141D4D9B0EFE2-8020
Alternator:
Multi Function Steering Wheel Control Module:
Subsystem 2 - Part No SW: 5G0 959 442 R HW: 5G0 959 442 R Labels: 3C8-959-537.CLB
Component: E221__MFL-DC1 H16 0040
Serial number: 29150000641010105136
Coding: 35FFFF
Power Converter DC AC:
Subsystem 3 - Part No SW: 5Q0 907 155 A HW: 5Q0 907 155 A
Component: WECHSELRICHTE H53 0041
Serial number: 0071941
1 Fault Found:
131702 - No Communication with Engine Control Module (SAE ECM/PCM)
U0100 00 [008] - -
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:00
Supply voltage: Terminal 30: 12.3 V
Terminal 15: On
-------------------------------------------------------------------------------
Address 2B: Steer. Col. Lock (J764) Labels:| 5Q0-905-861.clb
Part No SW: 5Q0 905 861 A HW: 5Q0 905 861 A
Component: ELV-MQBA H01 0120
Revision: 00000000 Serial number: 15000127554002
Coding: 5D00000000000000
Shop #: WSC 00066 790 07025
ASAM Dataset: EV_ELVMarquMQB 004111
ROD: EV_ELVMarquMQB_004_VW37.rod
VCID: 3424DC459F23E9E715-8060
2 Faults Found:
12666369 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:56
ELV State: 04
Information Clamps: 77 60
CoCo State: A0 01
WFS State: 17 06
Vehicle speed: 0.00 km/h
Voltage: 6B
AD-Value H-bridge: 35
Clamp15 flip flop: SSTx: button contacts: 06
CAN signals: 00
12666381 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
ELV State: 04
Information Clamps: 77 60
CoCo State: A0 01
WFS State: 17 06
Vehicle speed: 0.00 km/h
Voltage: 6B
AD-Value H-bridge: 35
Clamp15 flip flop: SSTx: button contacts: 06
CAN signals: 00
-------------------------------------------------------------------------------
Address 3C: Lane Change (J1086) Labels:* None
Part No SW: 5Q0 907 686 B HW: 5Q0 907 686 B
Component: HRE_Master H11 0071
Serial number: 0368374670
Coding: 02011103
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_HREntryHella 001028
ROD: EV_HREntryHella_VW32.rod
VCID: 3C34F465B77321A7DD-8068
Lane Change Assistant 2:
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386) Labels:| 5QX-959-X93-42.clb
Part No SW: 5Q0 959 593 E HW: 5Q0 959 593 B
Component: TSG FS 020 0041
Serial number: 0506150605043U
Coding: 003A13200000040000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_DCUDriveSideEWMAXKLO 006003
ROD: EV_DCUDriveSideEWMAXCONT_VW37.rod
VCID: 43C68F99CA8D5E5F9C-8016
Drivers Door Rear Control Module:
Subsystem 1 - Part No SW: 5Q4 959 811 D HW: 5Q4 959 811 D Labels: 5QX-959-81X-V1.CLB
Component: Fond FHSG DRV 007 0002
Serial number: 00000000000001360106
Coding: 011000
1 Fault Found:
458803 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 44: Steering Assist (J500) Labels:| 5Q0-909-144.clb
Part No SW: 5Q0 909 144 R HW: 5Q0 909 144 R
Component: EPS_MQB_ZFLS 126 1061
Coding: 1302
Shop #: WSC 00066 790 00221
ASAM Dataset: EV_SteerAssisMQB 012140
ROD: EV_SteerAssisMQB.rod
VCID: 43C68F99CA8D5E5F9C-8016
6 Faults Found:
22272 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Motor status: 00
System status: Waiting for start request
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 57
KFA: 00 00
Environmental conditions: 20
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.30 V
uAdSensI_SwitchedKl30_xdu16: 12.31 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
22528 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Motor status: 00
System status: Waiting for start request
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 58
KFA: 00 00
Environmental conditions: 20
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.30 V
uAdSensI_SwitchedKl30_xdu16: 12.31 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
23040 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Motor status: 03
System status: Driving mode
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 5A
KFA: 00 00
Environmental conditions: 20
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.30 V
uAdSensI_SwitchedKl30_xdu16: 12.31 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
22784 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Motor status: 03
System status: Driving mode
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 59
KFA: 00 00
Environmental conditions: 21
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.50 V
uAdSensI_SwitchedKl30_xdu16: 12.49 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
19460 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:59
Motor status: 03
System status: Driving mode
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 4C
KFA: 00 04
Environmental conditions: 20
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.30 V
uAdSensI_SwitchedKl30_xdu16: 12.31 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
23296 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:36:01
Motor status: 03
System status: Driving mode
Supply voltage: 12.25 V
Temperature: 52.0 ∞C
KFC: 5B
KFA: 00 00
Environmental conditions: 21
uAdSensI_U1V2Filtered_gdu16: 1.20 V
uAdSensI_U5VFiltered_xdu16: 0.00000 V
uioUdNotFilt_xdu16: 12.50 V
uAdSensI_SwitchedKl30_xdu16: 12.49 V
ASC_CTRL_GET_ILWS_ERR_FLAGS: 00
-------------------------------------------------------------------------------
Address 47: Sound System (J525) Labels:* None
Part No SW: 5Q0 035 456 HW: 5Q0 035 456
Component: MIB2_lite_amp H20 0110
Revision: 00000001 Serial number: VWZ8Z1FBA00BE4Z
Coding: 2200000000AAAAAA000000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_AMPMst12C1Gen2ALPI 001003
ROD: EV_AMPMst12C1Gen2ALPI.rod
VCID: 6D920921BC89782F1A-8038
No fault code found.
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387) Labels:| 5QX-959-X92-52.clb
Part No SW: 5Q0 959 592 E HW: 5Q0 959 592 B
Component: TSG BFS 020 0041
Serial number: 170615060504TQ
Coding: 003A13200000040000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_DCUPasseSideEWMAXKLO 006003
ROD: EV_DCUPasseSideEWMAXCONT_VW37.rod
VCID: 42C88A9DD597575797-8016
Passengers Rear Door Control Module:
Subsystem 1 - Part No SW: 5Q4 959 812 D HW: 5Q4 959 812 D Labels: 5QX-959-81X-V1.CLB
Component: Fond FHSG PSG 007 0002
Serial number: 00000000000001369331
Coding: 091000
1 Fault Found:
458803 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 55: Headlight Range (J745) Labels:| 7P6-907-357.clb
Part No SW: 7P6 907 357 D HW: 7P6 907 357 A
Component: AFS-ECU H07 0090
Revision: -------- Serial number: --------------
Coding: 061A00010B000400
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_HeadlRegulVWAFSMQB 001120
ROD: EV_HeadlRegulVWAFSMQB.rod
VCID: 40CC8095DB9B454781-8014
Left Headlamp Power Output Stage:
Subsystem 1 - Part No SW: 5N0 941 329 HW: 5N0 941 329 Labels: 3D0-941-329.CLB
Component: LeiMo links H01 0004
Coding: 2E0000
Right Headlamp Power Output Stage:
Subsystem 2 - Part No SW: 5N0 941 329 HW: 5N0 941 329 Labels: 3D0-941-329.CLB
Component: LeiMo rechts H01 0004
Coding: 2E0000
1 Fault Found:
13705475 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794) Labels:| 5G0-035-MIB-STD2.clb
Part No SW: 3Q0 035 876 HW: 3Q0 035 876
Component: MU-S-NS-US H25 0241
Serial number: VWZAZ2R0154122
Coding: 027302020000000051220002001808001F0100F401200105C6
Shop #: WSC 00066 790 07025
ASAM Dataset: EV_MUStd4CTSAT 001022
ROD: EV_MUStd4CTSAT_VW26.rod
VCID: 71AA1551A0B19CCF3E-8024
Operating And Display Unit 1:
Subsystem 1 - Part No SW: 5GM 919 605 HW: 5GM 919 605
Component: ABT_Std-2_Nav H52 1028
Serial number: VWZ8Z9RFC000K0
Data medium:
Subsystem 2 - Part No SW: 3G0 919 866 B HW: -----------
Component: NAR 2015/16 --- 0220
Serial number: --------------------
1 Fault Found:
6708 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
Voltage terminal 30: 12.4 V
Network diagnosis-Status: Enabled
-------------------------------------------------------------------------------
Address 75: Telematics (J949) Labels:| 5QE-035-285.clb
Part No SW: 5QE 035 285 A HW: 5QE 035 285 A
Component: OCULowMQBUS 007 0564
Coding: 02730202C2823A017F1E06000000
Shop #: WSC 00066 790 00323
ASAM Dataset: EV_OCULowMQB 001003
ROD: EV_OCULowMQB_VW37.rod
VCID: 43C68F99CA8D5E5F9C-8016
1 Fault Found:
0041 - Databus
U1123 00 [008] - Received Error Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:56
-------------------------------------------------------------------------------
Address A5: Frt Sens. Drv. Assist (R242) Labels:| 5Q0-980-653.clb
Part No SW: 5Q0 980 653 G HW: 5Q0 980 653
Component: MQB_MFK H06 0060
Serial number: 10000355732
Coding: 0100000000020306000400010100000100
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_MFKBoschAU370 001001
ROD: EV_MFKBoschAU370.rod
VCID: 3C34F465B77321A7DD-8068
2 Faults Found:
3080192 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:58
Control Module temperature: 61 ∞C
Outside air temperature: 29.5 ∞C
Vehicle speed: 0.00 km/h
Voltage terminal 15: 12.3 V
System run time: 1513.1 s
3670016 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 106
Mileage: 30278 km
Date: 2017.06.29
Time: 14:35:57
Control Module temperature: 61 ∞C
Outside air temperature: 29.5 ∞C
Vehicle speed: 0.00 km/h
Voltage terminal 15: 12.3 V
System run time: 1512.5 s
End----------(Elapsed Time: 02:03, VBatt start/end: 13.8V/13.7V)-----------
- Joined
- Dec 16, 2014
- Messages
- 7,989
- Reaction score
- 7,823
- Location
- Westbury, UK
- VCDS Serial number
- C?ID=1423
VCDS stores a log of all coding & adaptation changes, have you checked that you have reverted all of the changes you made (and no others)?
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
No - I haven't but now I will! Where would I find the logs (Applications>History Data)? I'm wondering why these would populate when my previous scan posted (#40) only showed "Relative Air Humidity Interior Sender: 1 Fault Found: 534549 - Databus U1121 00 [009] - Missing Message" - the only other change to the car was a APR Stage 1 coding by an installer. Is it possible that the programming done by the installer would have caused all the error messages (i.e. multiple missing message databus errors)?
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
McSpiffy: hello again. First-off, do you notice a pattern in your DTCs? Many of them have the following detail:
Fault Frequency: 1
Mileage: 30278 km
Date: 2017.06.29
which means that these errors have occurred only once and on no subsequent ignition cycle since then. When you say "after clearing the previous DTCs and restoring the car back to the previous coding (pre-Enable High Beam Assist efforts)" - did this occur on this date and mileage?
Also, the second part of your quote above seems to be at odds with the code-string for your BCM - see below:
As Dave has suggested, might be prudent to look in the directory C:\Ross-Tech\VCDS\Debug. Find the files AdpLog.CSV and CodingLog.CSV which contain a complete record-set of all the changes that you made with your laptop. If you used a Beta version software for some changes, also look at C:\Ross-Tech\VCDS-Beta\Debug subdirectory for a duplicate set of files.
Don
Fault Frequency: 1
Mileage: 30278 km
Date: 2017.06.29
which means that these errors have occurred only once and on no subsequent ignition cycle since then. When you say "after clearing the previous DTCs and restoring the car back to the previous coding (pre-Enable High Beam Assist efforts)" - did this occur on this date and mileage?
Also, the second part of your quote above seems to be at odds with the code-string for your BCM - see below:
As Dave has suggested, might be prudent to look in the directory C:\Ross-Tech\VCDS\Debug. Find the files AdpLog.CSV and CodingLog.CSV which contain a complete record-set of all the changes that you made with your laptop. If you used a Beta version software for some changes, also look at C:\Ross-Tech\VCDS-Beta\Debug subdirectory for a duplicate set of files.
Don
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Thank you Don and Dave for your helpful guidance! 062917 was the APR Stage 1 install - my previous VCDS scan was 062817 and the most-recent VCDS was last night (070117) so my thinking is that the APR installer was the source of the error codes. I'll peruse my Debugging files (thank you for pointing me in the right direction!) and see where I erred.
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Auto High Beam indicator displays in center cluster momentarily then Fault: Light Ass
Here is a list of the fault codes from my attempts at the HBA:
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Thursday,22,June,2017,12:36:27:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,present ,Thursday,22,June,2017,12:52:07:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,Not Present ,Tuesday,27,June,2017,19:51:31:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Saturday,01,July,2017,22:29:14:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Saturday,01,July,2017,22:30:20:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,Not Present ,Saturday,01,July,2017,22:33:03:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Friday,07,July,2017,18:04:26:06278
and my coding log:
Address 09,5Q0 937 087 AA,recoded (Long Coding),from,00511A464041A2E969E44000001407001800000000000000000000000000,to,00511B464041A2E969E44000001407001800000000000000000000000000,(00066/790/00211),Thursday,22,June,2017,12:55:02:06278
So should I switch my coding to the original line where the sixth alpha-numeric is an "A" instead of a "B"? Could this be the reason why an option for bi-xenon isn't displayed and all I get is for halogen? How do I go about changing the letter back?
I'm puzzled with the steps I've seen published since they don't match my vehicle. I make sure my light switch is off and I select control module>Common tab: 09-Cent. Elect.>Advanced Functions: Security Access-16 button>enter the code and select Do it!>select Advanced Functions: Adaptation-10 button>then select from a HUGE list of options IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent (instead of what most posts show as a simple "go to (2) Assistance light functions - menu light assistant and change to 'Present'. Am I misinterpreting the "09-Centreal Electronics adaptations: [2] Assistance Light Functions-Menuesteuerung Fernlichtassistent for the IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent that is listed in my huge dropdown window? Should I be doing the adaptation in a different menu of VCDS?
As Dave has suggested, might be prudent to look in the directory C:\Ross-Tech\VCDS\Debug. Find the files AdpLog.CSV and CodingLog.CSV which contain a complete record-set of all the changes that you made with your laptop. If you used a Beta version software for some changes, also look at C:\Ross-Tech\VCDS-Beta\Debug subdirectory for a duplicate set of files.
Don[/QUOTE]
Here is a list of the fault codes from my attempts at the HBA:
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Thursday,22,June,2017,12:36:27:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,present ,Thursday,22,June,2017,12:52:07:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,Not Present ,Tuesday,27,June,2017,19:51:31:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Saturday,01,July,2017,22:29:14:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Saturday,01,July,2017,22:30:20:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,present ,to,Not Present ,Saturday,01,July,2017,22:33:03:06278
Address 09,5Q0 937 087 AA,channel IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent,adapted from,Not Present ,to,present ,Friday,07,July,2017,18:04:26:06278
and my coding log:
Address 09,5Q0 937 087 AA,recoded (Long Coding),from,00511A464041A2E969E44000001407001800000000000000000000000000,to,00511B464041A2E969E44000001407001800000000000000000000000000,(00066/790/00211),Thursday,22,June,2017,12:55:02:06278
So should I switch my coding to the original line where the sixth alpha-numeric is an "A" instead of a "B"? Could this be the reason why an option for bi-xenon isn't displayed and all I get is for halogen? How do I go about changing the letter back?
I'm puzzled with the steps I've seen published since they don't match my vehicle. I make sure my light switch is off and I select control module>Common tab: 09-Cent. Elect.>Advanced Functions: Security Access-16 button>enter the code and select Do it!>select Advanced Functions: Adaptation-10 button>then select from a HUGE list of options IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent (instead of what most posts show as a simple "go to (2) Assistance light functions - menu light assistant and change to 'Present'. Am I misinterpreting the "09-Centreal Electronics adaptations: [2] Assistance Light Functions-Menuesteuerung Fernlichtassistent for the IDE08786-ENG116637-Assistance light functions-Menuesteuerung Fernlichtassistent that is listed in my huge dropdown window? Should I be doing the adaptation in a different menu of VCDS?
As Dave has suggested, might be prudent to look in the directory C:\Ross-Tech\VCDS\Debug. Find the files AdpLog.CSV and CodingLog.CSV which contain a complete record-set of all the changes that you made with your laptop. If you used a Beta version software for some changes, also look at C:\Ross-Tech\VCDS-Beta\Debug subdirectory for a duplicate set of files.
Don[/QUOTE]
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
McSpiffy: Great to hear from you again!! My apology if I'm getting this wrong, but I suspect that the problem here is the difference between the adaptation channel database and the code-string in a control module (I think). The two are entirely different albeit, I freely admit that I have never understood the fundamental reason why! Nevertheless, these two aspects of a control module are different and they are accessed in a different way.
Here's a visual instruction-set for how to change the code string on "the sixth alpha-numeric" (which nerds like me call the "lower nibble on Byte 2") from hexB to hexA. Please make sure that you use either a Beta, or release version 17.6 software - because this is the only way that you will access the now famous "yellow" long helper screens (and I assume that you are using a HEX series cable/dongle).
Hopefully the steps are self evident. If I have confused you, my apology - please ask for directions
Don
PS: If you are using an older style HEX+CAN, you may still be able to access the options in the "pull-down" facility on the 2nd last picture using the traditional long coding helper screen . Give it a try!!
Here's a visual instruction-set for how to change the code string on "the sixth alpha-numeric" (which nerds like me call the "lower nibble on Byte 2") from hexB to hexA. Please make sure that you use either a Beta, or release version 17.6 software - because this is the only way that you will access the now famous "yellow" long helper screens (and I assume that you are using a HEX series cable/dongle).
Hopefully the steps are self evident. If I have confused you, my apology - please ask for directions
Don
PS: If you are using an older style HEX+CAN, you may still be able to access the options in the "pull-down" facility on the 2nd last picture using the traditional long coding helper screen . Give it a try!!
Last edited:
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
That's AWESOME, Don! Thanks so much for clarifying (+visuals) . . . I'm starting to see the light! I guess my next question is should I go back and change the sixth alpha-numeric from a "B" back to an "A"?
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
MacSpiffy: Hi again. Was the word-play in your response a deliberate "paronomasia" (look it up), or was it an intentional pun?
If you have understood my visuals, you will see how easy it is to change the coding for Byte 2 - so yes, try restoring Byte 2 back to its original factory setting. If you haven't retrofitted any new headlight components to the car, then IMO it makes more sense to use the factory setting than a value that is meant for a higher-order piece of kit.
I'm not sure if you will get a an error message saying that re-calibration of the headlight range control modules is needed, but if it does - use the Ross Tech instructions HERE
Don
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Don,
A new "wrinkle" in my latest adjustment is that my backup camera no longer functions; would one of the other options under Byte 2 allow for the backup camera?
A new "wrinkle" in my latest adjustment is that my backup camera no longer functions; would one of the other options under Byte 2 allow for the backup camera?
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
McSpiffy: You are aware that the ONLY reason that I respond is because I like writing "McSpiffy"?
Seriously tho, no - the software switches in Byte 2 are as follows (in English):
Suggestions: Do you have any DTCs? If so, perhaps you might share a copy of your auto-scan with us.
Also, a perusal of the "history" report for the changes that have been made by your cable might be useful. Not sure if you are aware of this facility, but look in the C:\Ross-Tech\VCDS\Debug sub-directory (and C:\Ross-Tech\VCDS-Beta\Debug sub-directory if you also have the Beta SW version loaded) on the laptop that you use to make changes. In that sub-directory, you should find AdpLog.CSV and CodingLog.CSV - open these files and check the records for unintentional tweaks.
Don
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Backup camera no longer works and isn't recognized when selecting channel in VCDS
Since my recent change, I no longer have a backup camera functioning and now I have options under ACC for Eco/Normal/Sport . . . I don't recall having the choice previously.
Since my recent change, I no longer have a backup camera functioning and now I have options under ACC for Eco/Normal/Sport . . . I don't recall having the choice previously.
Code:
Tuesday,18,July,2017,17:44:58:06278
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 17.6.0.2 (x64) HEX-NET CB: 0.4341.4
Data version: 20170602 DS274
www.Ross-Tech.com
Dealer/Shop Name: Moose Lodge VW Den
VIN: 3VWC17AU4GM501532 License Plate: V93 8607
Mileage: 33052km-20537mi Repair Order: 071817B
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: AU (5Q0)
Scan: 01 02 03 05 08 09 10 13 15 16 17 19 2B 3C 42 44 47 52 55 5F
75 A5
VIN: 3VWC17AU4GM501532 Mileage: 33052km-20537miles
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: OK 0000
13-Auto Dist. Reg -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
2B-Steer. Col. Lock -- Status: OK 0000
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
55-Headlight Range -- Status: OK 0000
5F-Information Electr. -- Status: OK 0000
75-Telematics -- Status: OK 0000
A5-Frt Sens. Drv. Assist -- Status: OK 0000
-------------------------------------------------------------------------------
Address 01: Engine (J623-CXBB) Labels:. 06K-907-425-V1.clb
Part No SW: 8V0 906 264 F HW: 06K 907 425 B
Component: 1.8l R4 TFSI H13 0003
Revision: --H13---
Coding: 091A00322464002F1000
Shop #: WSC 00066 790 00221
ASAM Dataset: EV_ECM18TFS0208V0906264F 001003
ROD: EV_ECM18TFS0208V0906264F.rod
VCID: 3FCE8369A6653ABFF8-806A
No fault code found.
Readiness: 0000 0000
-------------------------------------------------------------------------------
Address 02: Auto Trans (J217) Labels: 09G-927-749-V2.clb
Part No SW: 09G 927 749 AP HW: 09G 927 749 AP
Component: AISIN AG6 G3 129 2943
Coding: 010200000C000000000000000000000000000000
Shop #: WSC 00066 790 00221
ASAM Dataset: EV_TCMAQ250031 002009
ROD: EV_TCMAQ250031_002_VW25.rod
VCID: 075E5B89BE35B27F80-8052
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104) Labels:. 5Q0-907-379-IPB-V1.clb
Part No SW: 3Q0 907 379 AB HW: 3Q0 907 379 G
Component: ESC H42 0723
Revision: 00000000 Serial number: 61255000000354
Coding: 04FA6AA12420096D007C020381C5292056249000408194B416435052C082
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_Brake1UDSContiMK100IPB 034036
ROD: EV_Brake1UDSContiMK100IPB_034_VW37.rod
VCID: 7AB8327DFDC7DF978F-802E
No fault code found.
-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. (J518) Labels:| 5Q0-959-435.clb
Part No SW: 5Q0 959 435 A HW: 5Q0 959 435
Component: VWKESSYMQB 021 0604
Revision: 00021000 Serial number: 0367374266
Coding: 030C0C
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_KessyHellaMQBAB 002011
ROD: EV_KessyHellaMQBAB_002_VW37.rod
VCID: 3A38F27DBD471F97CF-806E
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5G0-907-044.clb
Part No SW: 5GM 907 044 A HW: 5GM 907 044 A
Component: Climatronic H03 1001
Revision: 00001K01
Coding: 02020024200100000105000012111402
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_ACClimaBHBVW37X 003018
ROD: EV_ACClimaBHBVW37X_003_VW37.rod
VCID: 42C88A9DD597575797-8016
Fresh Air Blower Front:
Refrigerant Pressure And Temperature Sender:
Air quality sensor:
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519) Labels:| 5Q0-937-08X-MV1.clb
Part No SW: 5Q0 937 087 AA HW: 5Q0 937 087 AA
Component: BCM PQ37BOSCH 028 0162
Revision: -------- Serial number: 86581605150679
Coding: 005122464041A2E969E44000001407001800000000000000000000000000
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_BodyContrModul1UDSBosc 015002
ROD: EV_BCMBOSCH_015_VW37.rod
VCID: 7AB8327DFDC7DF978F-802E
Control Unit For Wiper Motor:
Subsystem 1 - Part No SW: 5GM 955 119 HW: 5GM 955 119 Labels: 5QX-955-119-V1.CLB
Component: WWS 150430 043 0581
Serial number: 150628095715
Coding: 0E4DDD
Rain Light Recognition Sensor:
Subsystem 2 - Part No SW: 5Q0 955 547 A HW: 5Q0 955 547 A Labels: 5Q0-955-547.CLB
Component: RLHS 037 0059
Serial number: S5Y15M05D11H20M57S08
Coding: 90A8DD
Sun Roof:
Subsystem 3 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J245 PS22.409 H03 0004
Serial number: 0000FST0009CPKU00000
Coding: 191800
Roof Blind:
Subsystem 4 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J394 PS22.409 H03 0004
Serial number: 0000FST0009CQ2D00000
Coding: 191800
Relative Air Humidity Interior Sender:
3 Faults Found:
534549 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 4
Reset counter: 121
Mileage: 32152 km
Date: 2017.07.07
Time: 20:44:55
204290 - Remote key 1
B1479 18 [009] - Current Too Low
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 77
Mileage: 32316 km
Date: 2017.07.08
Time: 12:45:16
329480 - Heated Passenger Seat
B1806 F0 [008] - Safety Shut-Off due to Occupant Detection
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 3
Reset counter: 124
Mileage: 32152 km
Date: 2017.07.07
Time: 20:46:01
-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J791) Labels:| 5Q0-919-298.clb
Part No SW: 5Q0 919 298 K HW: 5Q0 919 298
Component: PARKHILFE PLA H12 0054
Revision: -------- Serial number: 39431513200575
Coding: 0031165011
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_EPHVA2CAU3700000 003021
ROD: EV_EPHVA2CAU3700000_003_VW37.rod
VCID: 47DE9B89FEB5727F40-8012
No fault code found.
-------------------------------------------------------------------------------
Address 13: Auto Dist. Reg (J428) Labels:| 5Q0-907-572-V1.clb
Part No SW: 5Q0 907 572 F HW: 5Q0 907 572 D
Component: ACC Bosch MQB H05 0400
Serial number: 13031503210237
Coding: 01045400FE0739
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_ACCMRRBoschVW372 001016
ROD: EV_ACCMRRBoschVW372_VW26.rod
VCID: 3A38F27DBD471F97CF-806E
1 Fault Found:
1542 - Sensor for Automatic Distance Control
C110B F0 [008] - Limited Visibility
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 118
Mileage: 32741 km
Date: 2017.07.12
Time: 12:12:43
Control Module temperature: 33 ∞C
Voltage terminal 15: 13.7 V
Vehicle speed: 28.17 m/s
Acceleration: 0.02 m/s≤
-------------------------------------------------------------------------------
Address 15: Airbags (J234) Labels:| 5Q0-959-655.clb
Part No SW: 5Q0 959 655 J HW: 5Q0 959 655 J
Component: AirbagVW20 009 0825
Serial number: 003GCR01Y1DL
Coding: 8CCCFC00000000005000001AC24800000065
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_AirbaVW20SMEVW37X 002138
ROD: EV_AirbaVW20SMEVW37X_VW37.rod
VCID: 47DE9B89FEB5727F40-8012
Occupant Detection:
Subsystem 1 - Part No SW: 4M0 959 339 B HW: 4M0 959 339 B
Component: BF-Gewichtss. H11 0021
Serial number: IBH0000J1500031ZIL0K
Coding: 303137
Side Sensor Driver Front:
Subsystem 2 - Part No SW: ----------- HW: 480 002 305 15
Component: SideSensor_Df 001 0887
Serial number: 357000000000A560A418
Coding: 2D2D2D
Side Sensor Passenger Front:
Subsystem 3 - Part No SW: ----------- HW: 480 002 205 15
Component: SideSensor_Pf 001 0887
Serial number: 358000000000D0B06418
Coding: 2D2D2D
Side Sensor Driver Rear:
Subsystem 4 - Part No SW: ----------- HW: 480 402 704 15
Component: SideSensor_Dr 001 6149
Serial number: 3510002C91A91E714070
Coding: 2D2D2D
Side Sensor Passenger Rear:
Subsystem 5 - Part No SW: ----------- HW: 480 402 804 15
Component: SideSensor_Pr 001 6149
Serial number: 35200029B1A87872711+
Coding: 2D2D2D
Front Sensor Driver:
Subsystem 6 - Part No SW: ----------- HW: 480 400 505 15
Component: FrontSensor_D 001 6149
Serial number: 3550002AF1A8787292DL
Coding: 2D2D2D
Front Sensor Passenger:
Subsystem 7 - Part No SW: ----------- HW: 480 400 505 15
Component: FrontSensor_P 001 6149
Serial number: 3560002B31A878729376
Coding: 2D2D2D
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel (J527) Labels:| 5Q0-953-549.clb
Part No SW: 5Q0 953 521 BB HW: 5Q0 953 569 A
Component: Lenks.Modul 075 0175
Revision: FF032032 Serial number: 20150328500718
Coding: 0C10
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_SMLSVALEOMQB 001015
ROD: EV_SMLSVALEOMQB_VW37.rod
VCID: 73A61F59DAADAEDFCC-8026
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5G0-920-XXX-17.clb
Part No SW: 5G1 920 840 A HW: 5G1 920 840 A
Component: KOMBI 242 6420
Coding: 0BA4111AED98CF0502886A0B5000000000000000
Shop #: WSC 00066 790 00194
ASAM Dataset: EV_DashBoardVDDMQBAB 009046
ROD: EV_DashBoardVDDMQBAB_009_VW26.rod
VCID: 2502310124F9806F92-8070
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:| 5Q0-907-530-V1.clb
Part No SW: 5Q0 907 530 AF HW: 5Q0 907 530 M
Component: GW MQB High 212 2223
Revision: -------- Serial number: 22051510000845
Coding: 0901000830085900FB00021A1C0F00000001050000000000000000000000
Shop #: WSC 00066 790 00194
ASAM Dataset: EV_GatewConti 013020
ROD: EV_GatewConti_013_VW37.rod
VCID: 75A22141D4D9B0EFE2-8020
Alternator:
Multi Function Steering Wheel Control Module:
Subsystem 2 - Part No SW: 5G0 959 442 R HW: 5G0 959 442 R Labels: 3C8-959-537.CLB
Component: E221__MFL-DC1 H16 0040
Serial number: 29150000641010105136
Coding: 35FFFF
Power Converter DC AC:
Subsystem 3 - Part No SW: 5Q0 907 155 A HW: 5Q0 907 155 A
Component: WECHSELRICHTE H53 0041
Serial number: 0071941
No fault code found.
-------------------------------------------------------------------------------
Address 2B: Steer. Col. Lock (J764) Labels:| 5Q0-905-861.clb
Part No SW: 5Q0 905 861 A HW: 5Q0 905 861 A
Component: ELV-MQBA H01 0120
Revision: 00000000 Serial number: 15000127554002
Coding: 5D00000000000000
Shop #: WSC 00066 790 07025
ASAM Dataset: EV_ELVMarquMQB 004111
ROD: EV_ELVMarquMQB_004_VW37.rod
VCID: 3424DC459F23E9E715-8060
No fault code found.
-------------------------------------------------------------------------------
Address 3C: Lane Change (J1086) Labels:* None
Part No SW: 5Q0 907 686 B HW: 5Q0 907 686 B
Component: HRE_Master H11 0071
Serial number: 0368374670
Coding: 02011103
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_HREntryHella 001028
ROD: EV_HREntryHella_VW32.rod
VCID: 3C34F465B77321A7DD-8068
Lane Change Assistant 2:
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386) Labels:| 5QX-959-X93-42.clb
Part No SW: 5Q0 959 593 E HW: 5Q0 959 593 B
Component: TSG FS 020 0041
Serial number: 0506150605043U
Coding: 003A13200000040000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_DCUDriveSideEWMAXKLO 006003
ROD: EV_DCUDriveSideEWMAXCONT_VW37.rod
VCID: 43C68F99CA8D5E5F9C-8016
Drivers Door Rear Control Module:
Subsystem 1 - Part No SW: 5Q4 959 811 D HW: 5Q4 959 811 D Labels: 5QX-959-81X-V1.CLB
Component: Fond FHSG DRV 007 0002
Serial number: 00000000000001360106
Coding: 011000
No fault code found.
-------------------------------------------------------------------------------
Address 44: Steering Assist (J500) Labels:| 5Q0-909-144.clb
Part No SW: 5Q0 909 144 R HW: 5Q0 909 144 R
Component: EPS_MQB_ZFLS 126 1061
Coding: 1302
Shop #: WSC 00066 790 00221
ASAM Dataset: EV_SteerAssisMQB 012140
ROD: EV_SteerAssisMQB.rod
VCID: 43C68F99CA8D5E5F9C-8016
No fault code found.
-------------------------------------------------------------------------------
Address 47: Sound System (J525) Labels:* None
Part No SW: 5Q0 035 456 HW: 5Q0 035 456
Component: MIB2_lite_amp H20 0110
Revision: 00000001 Serial number: VWZ8Z1FBA00BE4Z
Coding: 2200000000AAAAAA000000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_AMPMst12C1Gen2ALPI 001003
ROD: EV_AMPMst12C1Gen2ALPI.rod
VCID: 6D920921BC89782F1A-8038
No fault code found.
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387) Labels:| 5QX-959-X92-52.clb
Part No SW: 5Q0 959 592 E HW: 5Q0 959 592 B
Component: TSG BFS 020 0041
Serial number: 170615060504TQ
Coding: 003A13200000040000000000
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_DCUPasseSideEWMAXKLO 006003
ROD: EV_DCUPasseSideEWMAXCONT_VW37.rod
VCID: 42C88A9DD597575797-8016
Passengers Rear Door Control Module:
Subsystem 1 - Part No SW: 5Q4 959 812 D HW: 5Q4 959 812 D Labels: 5QX-959-81X-V1.CLB
Component: Fond FHSG PSG 007 0002
Serial number: 00000000000001369331
Coding: 091000
No fault code found.
-------------------------------------------------------------------------------
Address 55: Headlight Range (J745) Labels:| 7P6-907-357.clb
Part No SW: 7P6 907 357 D HW: 7P6 907 357 A
Component: AFS-ECU H07 0090
Revision: -------- Serial number: --------------
Coding: 061A00010B000400
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_HeadlRegulVWAFSMQB 001120
ROD: EV_HeadlRegulVWAFSMQB.rod
VCID: 40CC8095DB9B454781-8014
Left Headlamp Power Output Stage:
Subsystem 1 - Part No SW: 5N0 941 329 HW: 5N0 941 329 Labels: 3D0-941-329.CLB
Component: LeiMo links H01 0004
Coding: 2E0000
Right Headlamp Power Output Stage:
Subsystem 2 - Part No SW: 5N0 941 329 HW: 5N0 941 329 Labels: 3D0-941-329.CLB
Component: LeiMo rechts H01 0004
Coding: 2E0000
No fault code found.
-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794) Labels:| 5G0-035-MIB-STD2.clb
Part No SW: 3Q0 035 876 HW: 3Q0 035 876
Component: MU-S-NS-US H25 0241
Serial number: VWZAZ2R0154122
Coding: 027302020000000051220002001808001F0100F401200105C6
Shop #: WSC 00066 790 07025
ASAM Dataset: EV_MUStd4CTSAT 001022
ROD: EV_MUStd4CTSAT_VW26.rod
VCID: 71AA1551A0B19CCF3E-8024
Operating And Display Unit 1:
Subsystem 1 - Part No SW: 5GM 919 605 HW: 5GM 919 605
Component: ABT_Std-2_Nav H52 1028
Serial number: VWZ8Z9RFC000K0
Data medium:
Subsystem 2 - Part No SW: 3G0 919 866 B HW: -----------
Component: NAR 2015/16 --- 0220
Serial number: --------------------
No fault code found.
-------------------------------------------------------------------------------
Address 75: Telematics (J949) Labels:| 5QE-035-285.clb
Part No SW: 5QE 035 285 A HW: 5QE 035 285 A
Component: OCULowMQBUS 007 0564
Coding: 02730202C2823A017F1E06000000
Shop #: WSC 00066 790 00323
ASAM Dataset: EV_OCULowMQB 001003
ROD: EV_OCULowMQB_VW37.rod
VCID: 43C68F99CA8D5E5F9C-8016
No fault code found.
-------------------------------------------------------------------------------
Address A5: Frt Sens. Drv. Assist (R242) Labels:| 5Q0-980-653.clb
Part No SW: 5Q0 980 653 G HW: 5Q0 980 653
Component: MQB_MFK H06 0060
Serial number: 10000355732
Coding: 0100000000020306000400010100000100
Shop #: WSC 01383 790 50316
ASAM Dataset: EV_MFKBoschAU370 001001
ROD: EV_MFKBoschAU370.rod
VCID: 3C34F465B77321A7DD-8068
No fault code found.
End----------(Elapsed Time: 01:44, VBatt start/end: 13.4V/13.5V)-----------
Last edited:
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Don, thanks for the info. I do have a few DTCs
I'm not sure why Relative Air Humidity Interior Sender keeps popping up; as soon as I clear it, it re-appears.
My spare key is dead so I replaced the battery - still doesn't work. I'll need to pop the protective cap off my door handle and pair the key with the car (assuming it was done in the first place from the dealership . . . )
No idea why the heated passenger seat safety shut-off came up; could it be that my MacBook Air is too heavy and the seat sensed it?
The sensor for the ADC flashed while driving home from WI last weekend; it was during a driving rain so I'm guessing the conditions caused it to fail. The date/time coincide with the occurence and since restarting, the ADC works fine. I can probably clear that DTC.
Another "weird" thing that occurs when attempting the adaptations is that a VCDS coding error 81: RPM too high pops up when the engine is running with VCDS. When I shut off the engine but leave the ignition on, I'm able to have the coding accepted.
Code:
Address 09: Cent. Elect. (J519) Labels:| 5Q0-937-08X-MV1.clb
Part No SW: 5Q0 937 087 AA HW: 5Q0 937 087 AA
Component: BCM PQ37BOSCH 028 0162
Revision: -------- Serial number: 86581605150679
Coding: 005122464041A2E969E44000001407001800000000000000000000000000
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_BodyContrModul1UDSBosc 015002
ROD: EV_BCMBOSCH_015_VW37.rod
VCID: 7AB8327DFDC7DF978F-802E
Control Unit For Wiper Motor:
Subsystem 1 - Part No SW: 5GM 955 119 HW: 5GM 955 119 Labels: 5QX-955-119-V1.CLB
Component: WWS 150430 043 0581
Serial number: 150628095715
Coding: 0E4DDD
Rain Light Recognition Sensor:
Subsystem 2 - Part No SW: 5Q0 955 547 A HW: 5Q0 955 547 A Labels: 5Q0-955-547.CLB
Component: RLHS 037 0059
Serial number: S5Y15M05D11H20M57S08
Coding: 90A8DD
Sun Roof:
Subsystem 3 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J245 PS22.409 H03 0004
Serial number: 0000FST0009CPKU00000
Coding: 191800
Roof Blind:
Subsystem 4 - Part No SW: 5G0 959 591 A HW: 8V3 959 591 A
Component: J394 PS22.409 H03 0004
Serial number: 0000FST0009CQ2D00000
Coding: 191800
Relative Air Humidity Interior Sender:
3 Faults Found:
534549 - Databus
U1121 00 [008] - Missing Message
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 4
Reset counter: 121
Mileage: 32152 km
Date: 2017.07.07
Time: 20:44:55
204290 - Remote key 1
B1479 18 [009] - Current Too Low
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 4
Fault Frequency: 1
Reset counter: 77
Mileage: 32316 km
Date: 2017.07.08
Time: 12:45:16
329480 - Heated Passenger Seat
B1806 F0 [008] - Safety Shut-Off due to Occupant Detection
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 3
Reset counter: 124
Mileage: 32152 km
Date: 2017.07.07
Time: 20:46:01
Address 13: Auto Dist. Reg (J428) Labels:| 5Q0-907-572-V1.clb
Part No SW: 5Q0 907 572 F HW: 5Q0 907 572 D
Component: ACC Bosch MQB H05 0400
Serial number: 13031503210237
Coding: 01045400FE0739
Shop #: WSC 00066 790 00211
ASAM Dataset: EV_ACCMRRBoschVW372 001016
ROD: EV_ACCMRRBoschVW372_VW26.rod
VCID: 3A38F27DBD471F97CF-806E
1 Fault Found:
1542 - Sensor for Automatic Distance Control
C110B F0 [008] - Limited Visibility
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 118
Mileage: 32741 km
Date: 2017.07.12
Time: 12:12:43
Control Module temperature: 33 ∞C
Voltage terminal 15: 13.7 V
Vehicle speed: 28.17 m/s
Acceleration: 0.02 m/s≤I'm not sure why Relative Air Humidity Interior Sender keeps popping up; as soon as I clear it, it re-appears.
My spare key is dead so I replaced the battery - still doesn't work. I'll need to pop the protective cap off my door handle and pair the key with the car (assuming it was done in the first place from the dealership . . . )
No idea why the heated passenger seat safety shut-off came up; could it be that my MacBook Air is too heavy and the seat sensed it?
The sensor for the ADC flashed while driving home from WI last weekend; it was during a driving rain so I'm guessing the conditions caused it to fail. The date/time coincide with the occurence and since restarting, the ADC works fine. I can probably clear that DTC.
Another "weird" thing that occurs when attempting the adaptations is that a VCDS coding error 81: RPM too high pops up when the engine is running with VCDS. When I shut off the engine but leave the ignition on, I'm able to have the coding accepted.
- Joined
- Aug 29, 2014
- Messages
- 75
- Reaction score
- 23
- Location
- Oswego, IL
- VCDS Serial number
- C?ID=224526
Don: Do you have a favorite cigar, coffee or beer that I can send you for all your help?
(That applies to you too, Ewe, if you're in Chicago for the trade show this week!)
(That applies to you too, Ewe, if you're in Chicago for the trade show this week!)
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
McSpiffy: hmm......... not quite sure how to say this tactfully and I certainly don't intend any offense, but can you explain the curious value that has been applied to Byte 2 - see comparison table below
Don
With your current setting for Byte 2 and by my reckoning - the binary string 00100010 means that BCM believes that the headlights are Xenon with AFS, the Brake control unit is not energized, the car has manual transmission and a manual spoiler is fitted! Shirley this can't be correct (except for the headlights)?
I'm totally confused!!!
Don