Results 1 to 8 of 8

Thread: VW golf 2002 remote control adaptation

  1. #1
    Verified VCDS User
    Join Date
    Jan 2020
    Location
    Israel
    Posts
    52
    Post Thanks / Like

    VW golf 2002 remote control adaptation

    hello all
    i hope you are doing well.
    im trying to adapt a remote control for this car but there is no channel 01 nor 21
    i entered wiki.rosstech on this link "https://www.ross-tech.com/vag-com/cars/vw-remote-matching.html"
    If the above procedure does not work (neither Channel 01 nor Channel 21 are available), follow this procedure:

    Insert a working (old) key in the ignition and turn to the ON position (do not start car).

    [Select]

    [46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)

    [Meas. Blocks - 08]

    Enter group "003" (may be group "007" in some vehicles)

    [Go!]

    The value in field 2 shows how many remotes have been matched and in which memory positions (for example, "0001" indicates 1 transmitter in position 1).
    and tried the second way, but on this car all basic settings says not available,field 2 says "not oper"
    could be something wrong with the 46.central conv. itself, 35 central locking is not installed.

    thanks

  2. #2
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    28,369
    Post Thanks / Like
    Blog Entries
    1
    If you have 46, then it should be Channel 01:
    http://wiki.ross-tech.com/wiki/index..._3)#Adaptation
    (see also the video at the bottom of that page)

    -Uwe-
    Lock-down of sick people: Quarantine
    Lock-down of healthy people: Tyranny

  3. Likes Jack@European_Parts liked this post
  4. #3
    Verified VCDS User
    Join Date
    Jan 2020
    Location
    Israel
    Posts
    52
    Post Thanks / Like
    thanks
    i think there is something wrong with the unit itself

  5. #4
    Verified VCDS User
    Join Date
    Jan 2020
    Location
    Poland
    Posts
    62
    Post Thanks / Like
    You can try this procedure, I used to do it and it worked. Turn the ignition on with the key.

    Get out of the car, leaving the working key inside.

    Lock the car with a new key by turning it in the driver's door lock.

    Press any button on the new remote control 1, 2, 3 or 4 times to assign this remote control to 1, 2, 3 or 4 fields in the controller. Do presses at a rate of about 1 per second.

    Wait 5 seconds.

    Press any button on the new remote control again.

    The key coding should be confirmed by an acoustic signal or emergency lights.

    Open the car.

    Turn the ignition off.

  6. Likes Uwe, Dana, Jack@European_Parts liked this post
  7. #5
    Verified VCDS User
    Join Date
    Jan 2020
    Location
    Israel
    Posts
    52
    Post Thanks / Like
    Thanks a lot
    I will try that

  8. #6
    Verified VCDS User
    Join Date
    Jan 2020
    Location
    Israel
    Posts
    52
    Post Thanks / Like
    I tried this way but it didn't work
    Though there is another remote that works fine on the car but it not showed when I enter 46 control unit because every time I enter adaptation - remote control matching it says channel not available
    What might be the problem

  9. #7
    Ross-Tech Employee Dana's Avatar
    Join Date
    Jan 2014
    Location
    United States
    Posts
    4,154
    Post Thanks / Like
    That could be a communication error (for any number or reasons) or a faulty module. Please post the Auto-Scan so we can see if everything else is OK in addition to the installed control module details.

    It might not hurt to reboot (unplug) the 46 module but please save a scan before doing so.

  10. Likes MartinsX liked this post
  11. #8
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,581
    Post Thanks / Like
    Post an auto-scan please..........
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •