Results 1 to 8 of 8

Thread: 2007 RS4 Manifold Flaps Stuck Code

  1. #1
    Verified VCDS User
    Join Date
    Feb 2020
    Location
    USA
    Posts
    8
    Post Thanks / Like

    2007 RS4 Manifold Flaps Stuck Code

    So I just finished doing a carbon cleaning on my car and still have the front bumper off yet I wanted to make sure it runs with no leaks or anything, after 20 mins to build confidence in everything I shut it off, then cleared all current codes and rescanned. I seen the manifold bank1 and 2 stuck and I was wondering what happened since I replaced both of those sensors as well as did the 034 billet linkage kit and when I tested them on the table they moved freely under 5lbs of vacuum. When I go to basic settings on engine 1/2 group 142 and try it they get stuck at ADT run. I have many simple codes that are there for the battery being disconnected that will go away just worried about the engine ones, any help would be greatly appreciated .

    Code:
    Wednesday,25,March,2020,17:10:17:10776
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
    VCDS Version: 19.6.2.2 (x64)  HEX-NET CB: 0.4508.4
    Data version: 20200210 DS308.0
    www.Ross-Tech.com
    
    
    VIN: WUARU98E37N904408   License Plate: 
    
    
    Chassis Type: 8E (8E - Audi A4/S4/RS4 B6/B7 (2001 > 2008))
    Scan: 01 02 03 08 09 0F 11 15 16 17 18 25 36 37 45 46 55 56 57 65
              67 69 75 76 77
     
    VIN: WUARU98E37N904408   Mileage: 158890km-98729miles
    -------------------------------------------------------------------------------
    Address 01: Engine        Labels:. 079-910-560-BNS1.lbl
       Part No SW: 8E1 910 560 A    HW: 8E1 907 560 
       Component: 4.2L V8/4V FSI     Ş0060  
       Revision: 57H13---    Serial number: XXXXXXXXXXXXXX
       Coding: 01040009180F0160
       Shop #: WSC 05140 444 85886
       VCID: A4044A8767F1676F61-80F0
    
    2 Faults Found:
    008198 - Intake Manifold Flap; Bank 1 
                   P2006 - 008 - Stuck Closed - Intermittent
                 Freeze Frame:
                        Fault Status: 00101000
                        Fault Priority: 0
                        Fault Frequency: 1
                        Reset counter: 255
                        Mileage: 158898 km
                        Time Indication: 0
    
                 Freeze Frame:
                        RPM: 974 /min
                        Load: 19.6 %
                        Speed: 0.0 km/h
                        Temperature: 72.0°C
                        Temperature: 45.0°C
                        Absolute Pres.: 980.0 mbar
                        Voltage: 11.684 V
    
    006435 - Please Check DTC Memory of ECU Number 2 
                   P1923 - 008 - 
                 Freeze Frame:
                        Fault Status: 01101000
                        Fault Priority: 0
                        Fault Frequency: 1
                        Reset counter: 255
                        Mileage: 158898 km
                        Time Indication: 0
    
                 Freeze Frame:
                        RPM: 0 /min
                        Load: 0.0 %
                        Speed: 0.0 km/h
                        Temperature: 77.0°C
                        Temperature: 45.0°C
                        Absolute Pres.: 980.0 mbar
                        Voltage: 12.065 V
    
    Readiness: 0110 1101
    
    -------------------------------------------------------------------------------
    Address 03: ABS Brakes        Labels: 8E0-910-517.clb
       Part No SW: 8E0 910 517 G    HW: 8E0 614 517 BD
       Component: ESP8 quattro    H06 0150  
       Revision: 00000000    Serial number: 00000000000000
       Coding: 0004533
       Shop #: WSC 06335 000 00000
       VCID: AB16A1BB0A2FA817A0-80FE
    
    1 Fault Found:
    01826 - Sensor for Steering Angle (G85); Supply Voltage Terminal 30 
                000 - -
                 Freeze Frame:
                        Fault Status: 01100000
                        Fault Priority: 3
                        Fault Frequency: 3
                        Reset counter: 40
                        Time Indication: 0
    
                 Freeze Frame:
                        Hex Value: 0x0000
                        Hex Value: 0x4222
                        Hex Value: 0x0024
                        Hex Value: 0x0191
                        Hex Value: 0x0001
    
    
    -------------------------------------------------------------------------------
    Address 08: Auto HVAC        Labels: 8E0-820-043.lbl
       Part No: 8E0 820 043 BM
       Component:   A4 Klimaautomat   2833  
       Coding: 00000
       Shop #: WSC 00000  
       VCID: ED926FA3A5BB6627FE-50F4
    
    1 Fault Found:
    01317 - Control Module in Instrument Cluster (J285) 
                79-00 - Please Check Fault Codes
    
    -------------------------------------------------------------------------------
    Address 09: Cent. Elect.        Labels: 8E0-907-279-8EC.lbl
       Part No: 8E0 907 279 N
       Component: int. Lastmodul  USA 0907  
       Coding: 01023
       Shop #: WSC 06335  
       VCID: BD329FE3B55B36A70E-4AA4
    
    4 Faults Found:
    01496 - Bulb for Fog-Lamps; Left (L22) 
                30-00 - Open or Short to Plus
    01500 - Bulb for Fog-Lamps; Right (L23) 
                30-00 - Open or Short to Plus
    01520 - Rain and Light Recognition Sensor (G397) 
                27-00 - Implausible Signal
    01520 - Rain and Light Recognition Sensor (G397) 
                62-00 - No or Incorrect Adjustment
    
    -------------------------------------------------------------------------------
    Address 11: Engine II        Labels:. 079-910-560-BNS2.lbl
       Part No SW: 8E1 910 560 A    HW: 8E1 907 560 
       Component: 4.2L V8/4V FSI     Ş0060  
       Revision: 57H13---    Serial number: XXXXXXXXXXXXXX
       Coding: 01040009180F0160
       Shop #: WSC 05140 444 85886
       VCID: A4044A8767F1676F61-80F0
    
    1 Fault Found:
    008199 - Intake Manifold Flap; Bank 2 
                   P2007 - 008 - Stuck Closed - Intermittent
                 Freeze Frame:
                        Fault Status: 00101000
                        Fault Priority: 0
                        Fault Frequency: 1
                        Reset counter: 255
                        Mileage: 158898 km
                        Time Indication: 0
    
                 Freeze Frame:
                        RPM: 977 /min
                        Load: 19.6 %
                        Speed: 0.0 km/h
                        Temperature: 72.0°C
                        Temperature: 45.0°C
                        Absolute Pres.: 980.0 mbar
                        Voltage: 11.557 V
    
    
    -------------------------------------------------------------------------------
    Address 15: Airbags        Labels: 8E0-959-655-94.lbl
       Part No SW: 8E0 959 655 H    HW: 8E0 959 655 H
       Component:    Airbag 9.41  H12 3840  
       Revision: 91H12384    Serial number: 0036N0G0J1J1  
       Coding: 0432707
       Shop #: WSC 06335 000 00000
       VCID: BC3492E7FF413FAF39-80E8
    
       Subsystem 1 - Part No: 8E0 910 339 B
       Component: BF-Gewichtsens. 002 0070
    
       Subsystem 2 - Serial number: 3HKJ4         
    
       Subsystem 3 - Serial number: 0001.01.000000200000000000˙†63
    
       Subsystem 4 - Serial number: 000000˙†6332DRB4042615203˙†63
    
       Subsystem 5 - Serial number: 615203˙†6342DRB4042606158˙†63
    
       Subsystem 6 - Serial number: 606158˙†6352ARB401D1C3E4U˙†63
    
       Subsystem 7 - Serial number: 1C3E4U˙†6362ARB4018AEEFAC˙†63
    
       Subsystem 8 - Serial number: AEEFAC˙†63729RB401CD3E92.˙†63
    
       Subsystem 9 - Serial number: D3E92.˙†63829RB401CD3EA2$˙
    
       Subsystem 10 - Serial number: D3EA2$˙
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 16: Steering wheel        Labels: 8E0-953-549-T.lbl
       Part No: 8E0 953 549 T
       Component: Lenksáulenmodul     0301  
       Coding: 04441
       Shop #: WSC 06335  
       VCID: C4C4EA07D6B1476F41-4AA4
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 17: Instruments        Labels: 8E0-920-9xx-8EC.lbl
       Part No SW: 8E0 920 982 R    HW: 8E0 920 982 R
       Component: KOMBI+WFS 4     H14 0100  
       Revision: 0100        Serial number: 00000000000000
       Coding: 0023268
       Shop #: WSC 44706 000 1048576
       VCID: BD329FE3E55B36A70E-50F4
    
    1 Fault Found:
    00779 - Outside Air Temp Sensor (G17) 
                010 - Open or Short to Plus
    
    -------------------------------------------------------------------------------
    Address 25: Immobilizer        Labels: 8E0-920-9xx-8EC.lbl
       Part No SW: 8E0 920 982 R    HW: 8E0 920 982 R
       Component: KOMBI+WFS 4     H14 0100  
       Revision: 0100        Serial number: 00000000000000
       Coding: 0023268
       Shop #: WSC 44706 000 1048576
       VCID: BD329FE3E55B36A70E-5118
    
    1 Fault Found:
    00779 - Outside Air Temp Sensor (G17) 
                010 - Open or Short to Plus
    
    -------------------------------------------------------------------------------
    Address 36: Seat Mem. Drvr        Labels: 8E0-959-760.lbl
       Part No: 8E0 959 760 
       Component: Sitzmemory R2 F     0305  
       Coding: 00002
       Shop #: WSC 00000  
       VCID: F1AA73D3BA8382C7DA-4B1E
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 46: Central Conv.        Labels:. 8E0-959-433-MAX.clb
       Part No: 8E0 959 433 CG
       Component: Komfortgerát T7B    4135  
       Coding: 11816
       Shop #: WSC 06335  
       VCID: F8BC4EF7DAF9D38F1D-4AA4
    
       Subsystem 1 - Part No: 8E1959801G
       Component: Tőrsteuer.FS BRM 0706  
    
       Subsystem 2 - Part No: 8E1959802G
       Component: Tőrsteuer.BF BRM 0706  
    
       Subsystem 3 - Part No: 8E0959801E
       Component: Tőrsteuer.HL BRM 0606  
    
       Subsystem 4 - Part No: 8E0959802E
       Component: Tőrsteuer.HR BRM 0606  
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 55: Headlight Range        Labels: 4F0-910-357.lbl
       Part No SW: 4F0 910 357 F    HW: 4F0 907 357 F
       Component: AFS 1           H01 0020  
       Revision: 00000001    Serial number:               
       Coding: 0000019
       Shop #: WSC 06335 000 00000
       VCID: A91A5BB300D3BA0752-80FC
    
       Subsystem 1 - Part No: 8E0 941 329 A
       Component: AFS-Modul links H03 0020
    
       Subsystem 2 - Part No: 8E0 941 329 A
       Component: AFS-Modul rechtsH03 0020
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 65: Tire Pressure        Labels: 8E0-907-273.lbl
       Part No SW: 8E0 907 273 A    HW: 8E0 907 273 A
       Component: Reifendruck 3   H04 0130  
       Coding: 0062523
       Shop #: WSC 02197 785 00200
       VCID: AA18A4BF07D5B11F5B-513C
    
    No fault code found.
    
    -------------------------------------------------------------------------------
    Address 77: Telephone        Labels: 8P0-862-335.lbl
       Part No SW: 8P1 862 336 A    HW: 8P1 862 336 
       Component: FSE_256x BT     H44 0660  
       Revision: 00000000    Serial number: 00000005179874
       Coding: 0011877
       Shop #: WSC 40310 001 1048576
       VCID: B62080CFC06DE5FFCF-50D0
    
    No fault code found.
    
    End----(Elapsed Time: 05:08, VBatt start/end: 11.9V/11.9V. VIgn 11.8V)-----

  2. #2
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,246
    Post Thanks / Like
    Low voltages?

    Wiring inadequate to carry current or connections poor?

    Retrace work steps and verify FOD removed to isolate possible contamination of modified part?

    JPPSG

    https://forums.ross-tech.com/showthr...uot-JPPSG-quot

    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  3. #3
    Verified VCDS User
    Join Date
    Feb 2020
    Location
    USA
    Posts
    8
    Post Thanks / Like
    Quote Originally Posted by Jack@European_Parts View Post
    Low voltages?

    Wiring inadequate to carry current or connections poor?

    Retrace work steps and verify FOD removed to isolate possible contamination of modified part?

    JPPSG

    https://forums.ross-tech.com/showthr...uot-JPPSG-quot

    That was part of what codes I was saying not to pay attention too, I didnt have it hooked up to a charger, I just took it for a test drive and scanned it when it came back those codes are gone its still showing the manifold flap codes tho.

  4. #4
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,246
    Post Thanks / Like
    That was part of what codes I was saying not to pay attention too, I didnt have it hooked up to a charger, I just took it for a test drive and scanned it when it came back those codes are gone its still showing the manifold flap codes tho.
    Did you Un-stick the intake flaps than and verify the full swing or sensor placement to achieve the ADP in VCDS blocks?
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  5. #5
    Verified VCDS User
    Join Date
    Feb 2020
    Location
    USA
    Posts
    8
    Post Thanks / Like
    Quote Originally Posted by Jack@European_Parts View Post
    Did you Un-stick the intake flaps than and verify the full swing or sensor placement to achieve the ADP in VCDS blocks?
    with both the new sensors on bank 1 ill read 0-99.4 and bank 2 ill read 14-99.4/6 I cant get the drivers bank to read correctly currently, yet I can freely move them in the car, fighting the check valve they are hooked to of course.
    I took a snapshot but dont know how to attach it here.

  6. #6
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,246
    Post Thanks / Like
    with both the new sensors on bank 1 ill read 0-99.4 and bank 2 ill read 14-99.4/6 I cant get the drivers bank to read correctly currently, yet I can freely move them in the car, fighting the check valve they are hooked to of course.
    I took a snapshot but dont know how to attach it here.

    Maybe something is hooked up incorrectly check routing yet as per RTFB?

    Are valves on device zone?

    https://forums.ross-tech.com/showthr...-Post-Pictures
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  7. #7
    Verified VCDS User
    Join Date
    Feb 2020
    Location
    USA
    Posts
    8
    Post Thanks / Like
    Quote Originally Posted by Jack@European_Parts View Post
    Maybe something is hooked up incorrectly check routing yet as per RTFB?

    Are valves on device zone?

    https://forums.ross-tech.com/showthr...-Post-Pictures
    well, thanks for the attempt sadly I found something that may be part of the problem yet not 100% the cause, so gotta take the manifold off again, gonna delete this post as it isnt needed at the moment

  8. #8
    Verified VCDS User PetrolDave's Avatar
    Join Date
    Dec 2014
    Location
    South Molton, UK
    Posts
    3,214
    Post Thanks / Like
    As the intake flaps that engine are vacuum operated you need to check ALL the vacuum piping to not only the intake flaps but also the power flap (in the air cleaner box) and the exhaust flaps.

  9. Likes Jack@European_Parts, Uwe liked this post

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •