Good evening all
First time poster so please be gentle
I own a 2007 VW T5 2.5 BNZ, bought it last year. So far ive had the turbo reconditioned, ive replaced the N75 module, the EGR cooler (bladder had crapped itself), i have also replaced the EGR and the throttle body.
Most of these have been replaced as codes where showing that they weren't operating right and have fixed most of the issues however i am unable to resolve what seems to be the last issue that is causing the coil light of death to come on.
So, I clear the codes using VCDS lite, i can start the van with no issues, i can drive the van around on normal roads around 30 - 40 with absolutely no issue what so ever, however if i take it onto the motorway as soon as i get up to around 60mph sometimes more sometimes less the coil light comes on, as soon as i stop and turn the ignition off and on it resets itself and i can carry on, sometimes i may be able to complete my journey other times ill get the coil light a few times. It does seem to come on more and quicker when its colder but not just sure if that is coincidence or not. if i clear it as well and turn the ignition on but dont start the engine the coil light will also come on after about a minute which im assuming is due to it going through some sort of cycle.
As mentioned above I have fitted a new throttle body to the van and i have read that i need to complete a throttle body alignment however when i type the code 60 into the group on the basic settings i get an error message "Error Group 60 Not Available", i have tried typing the same code into the meas blocks and it just stays blank. I contacted the support team and was told that the alignment is not available for my van as it is a diesel and not a petrol so i am now at a loss. One other thing i should mention is that when i look at the readiness option in 01 engine it says all is ok apart from the EGR which shows as failed or incomplete, i have checked that the new cooler is operating properly using the test on VCDS lite but I need to get access to view if the EGR itself is operating properly which im going to try and do over the weekend, is it possible that the the two of these are linked.
I am at a complete loss now as i just assumed the TBA would solve the P2015 issue but being told i cant do it has left me stranded. Please find below the auto scan from 2 days ago, I should also add, whilst this reading was done with VCDS lite, i did also try to complete a TBA using my mates full version of VCDS with HEX CAN+ dongle and got the same error.
Any help will be greatly appreciated.
First time poster so please be gentle
I own a 2007 VW T5 2.5 BNZ, bought it last year. So far ive had the turbo reconditioned, ive replaced the N75 module, the EGR cooler (bladder had crapped itself), i have also replaced the EGR and the throttle body.
Most of these have been replaced as codes where showing that they weren't operating right and have fixed most of the issues however i am unable to resolve what seems to be the last issue that is causing the coil light of death to come on.
So, I clear the codes using VCDS lite, i can start the van with no issues, i can drive the van around on normal roads around 30 - 40 with absolutely no issue what so ever, however if i take it onto the motorway as soon as i get up to around 60mph sometimes more sometimes less the coil light comes on, as soon as i stop and turn the ignition off and on it resets itself and i can carry on, sometimes i may be able to complete my journey other times ill get the coil light a few times. It does seem to come on more and quicker when its colder but not just sure if that is coincidence or not. if i clear it as well and turn the ignition on but dont start the engine the coil light will also come on after about a minute which im assuming is due to it going through some sort of cycle.
As mentioned above I have fitted a new throttle body to the van and i have read that i need to complete a throttle body alignment however when i type the code 60 into the group on the basic settings i get an error message "Error Group 60 Not Available", i have tried typing the same code into the meas blocks and it just stays blank. I contacted the support team and was told that the alignment is not available for my van as it is a diesel and not a petrol so i am now at a loss. One other thing i should mention is that when i look at the readiness option in 01 engine it says all is ok apart from the EGR which shows as failed or incomplete, i have checked that the new cooler is operating properly using the test on VCDS lite but I need to get access to view if the EGR itself is operating properly which im going to try and do over the weekend, is it possible that the the two of these are linked.
I am at a complete loss now as i just assumed the TBA would solve the P2015 issue but being told i cant do it has left me stranded. Please find below the auto scan from 2 days ago, I should also add, whilst this reading was done with VCDS lite, i did also try to complete a TBA using my mates full version of VCDS with HEX CAN+ dongle and got the same error.
Any help will be greatly appreciated.
Code:
VCDS-Lite Version: Release 1.2
Monday, 09 March 2020, 20:18:33:58806
Chassis Type: 7H - VW Transporter
Scan: 01,02,03,08,09,0B,0D,15,16,17,18,19,1C,22,2D,37,45,46,47,56,57,6E,76,77,78,7D
-------------------------------------------------------------------------------
Address 01: Engine Labels: 070-906-016-AXD.LBL
Controller: 070 906 016 CG
Component: R5 2,5L EDC G000AG 9015
Coding: 0001075
Shop #: WSC 66565
VCID: 57C1EDE9A615
1 Fault Found:
008213 - Intake Manifold Flap Position Sensor (Bank 1): Implausible Signal
P2015 - 000 - -
Readiness: N/A
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: Redir Fail!
Controller: 09K 927 750 K
Component: AQ 250 6F 0864
Coding: 0000072
Shop #: WSC 02744
VCID: 3D0D5F412469
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: Redir Fail!
Controller: 7H0 907 379 P
Component: (M)ABS MK25E 0103
Coding: 0000552
Shop #: WSC 02744
VCID: 42F72CBD5D97
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: Redir Fail!
Controller: 7H0 820 045 AH
Component: CLIMA/AC 0303
Coding: 0000000
Shop #: WSC 00000
VCID: 6BA9A1190A9D
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 7H0-937-049.LBL
Controller: 7H0 937 049 AA
Component: BORDNETZ SGVER 1.0 2001
Coding: 0000101
Shop #: WSC 02744
VCID: 7195B37128B1
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 6Q0-909-605-VW5.LBL
Controller: 1C0 909 605 A
Component: 3B AIRBAG VW51 0009
Coding: 13122
Shop #: WSC 02744
VCID: 22378C3DBDD7
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments Labels: 7Hx-920-xxx-17.LBL
Controller: 7H0 920 951 P
Component: KOMBI+WEGFAHRSP VDO V02
Coding: 01412
Shop #: WSC 00186
VCID: 39054B513041
WV2ZZZ7HZ7H024577 VWZ7Z0F3993438
1 Fault Found:
01304 - Radio
49-00 - No Communications
-------------------------------------------------------------------------------
Address 18: Aux. Heat Labels: Redir Fail!
Controller: 7H0 815 071 E
Component: Standheizung 0207
Coding: 0000000
Shop #: WSC 00000
VCID: 2A27641DC5E7
2 Faults Found:
01320 - Control Module for Climatronic (J255)
013 - Check DTC Memory - Intermittent
01126 - Engine Speed Signal
008 - Implausible Signal - Intermittent
-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 6N0-909-901-19.LBL
Controller: 6N0 909 901
Component: Gateway K<->CAN 0001
Coding: 00006
Shop #: WSC 02744
VCID: F0933675A3BB
1 Fault Found:
01304 - Radio
49-00 - No Communications
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 7H0-959-433.LBL
Controller: 7H0 959 433 BCv
Component: 2L Komfortgerát 0004
Coding: 00069
Shop #: WSC 02744
VCID: EBA921198A9D
No fault code found.
-------------------------------------------------------------------------------
Address 76: Park Assist Labels: 7H0-919-283.LBL
Controller: 7H0 919 283
Component: Parkingsyst. T5 T5N 401
Coding: 01137
Shop #: WSC 02744
VCID: EF913509BE85
No fault code found.
End --------------------------------------------------------------------------------------------------
Last edited by a moderator:
