Hi all, hopefully you can help me. I have an 08 Aud A4 Avant Quattro that started life as a 2.0l petrol automatic. I have since swapped in an AZV 2.0 16v TDI and converted the gearbox to an 0A3 6 speed manual. Wiring harness used was from a period correct Audi A4 TDI.
As you can imagine, there are some conflicts. The two that I am most vexed by are the ECU for the AZV will not take coding to tell it that it is in an AWD car.
The other is the ABS module (Bosch 8.0) is doing a lot of complaining. Glow plug light flashing, ABS light on, brake light on, brake light warning in DIS display on, traction control light on, beeping. I would love to make all these things play nicely together so I can finish this car and give it to my wife and get it off my plate. There is no coding suggestion in the ABS module when using VCDS like there is in all the other modules. It states to contact Ross Tech to which I am told I should just post here and maybe someone can help me as they dont know any of the coding for this.
as you can see in the autoscan, there is a glowplug control module fault, but I suspect this is due to the wiring differences between the AZV ecu expectancies vs the wiring harness that I have used which is from a BRE for an Audi that was equipped with this engine.
To be clear the main focus is dealing with the two codes in the ABS module that state to check the coding of the other modules and the airbag control module. The airbag code wasnt there before any of this work was done and no coding has been changed to the airbag module that I recall, but its been a long time. I can state that as far as the airbag system goes, I did swap in some B6 recaros of which yielded two faults. One for the seat recognition signal from the passenger seat implausible (which I learned was due to a unique to 2008 bladder in the seat) which I sorted by swapping the bladder from the stock seat into the recaro. The other being the centre rear seatbelt ignitor code which has to do with the differences between the two pyrotechnic seatbelt retractors. That was swapped too and as you can see there are no faults in the airbag module.
Thanks for any help. I do expect and am prepared that I may need to buy an ECU from a BRE so the Audi electronics will be happy, so I am not ruling that out.
As you can imagine, there are some conflicts. The two that I am most vexed by are the ECU for the AZV will not take coding to tell it that it is in an AWD car.
The other is the ABS module (Bosch 8.0) is doing a lot of complaining. Glow plug light flashing, ABS light on, brake light on, brake light warning in DIS display on, traction control light on, beeping. I would love to make all these things play nicely together so I can finish this car and give it to my wife and get it off my plate. There is no coding suggestion in the ABS module when using VCDS like there is in all the other modules. It states to contact Ross Tech to which I am told I should just post here and maybe someone can help me as they dont know any of the coding for this.
as you can see in the autoscan, there is a glowplug control module fault, but I suspect this is due to the wiring differences between the AZV ecu expectancies vs the wiring harness that I have used which is from a BRE for an Audi that was equipped with this engine.
To be clear the main focus is dealing with the two codes in the ABS module that state to check the coding of the other modules and the airbag control module. The airbag code wasnt there before any of this work was done and no coding has been changed to the airbag module that I recall, but its been a long time. I can state that as far as the airbag system goes, I did swap in some B6 recaros of which yielded two faults. One for the seat recognition signal from the passenger seat implausible (which I learned was due to a unique to 2008 bladder in the seat) which I sorted by swapping the bladder from the stock seat into the recaro. The other being the centre rear seatbelt ignitor code which has to do with the differences between the two pyrotechnic seatbelt retractors. That was swapped too and as you can see there are no faults in the airbag module.
Thanks for any help. I do expect and am prepared that I may need to buy an ECU from a BRE so the Audi electronics will be happy, so I am not ruling that out.
Code:
VIN: WAUKF78E68A107783 License Plate: CLNDSL
Mileage: 204800km-127256mi Repair Order:
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: 8E (8E - Audi A4/S4/RS4 B6/B7 (2001 > 2008))
Scan: 01 02 03 08 09 0F 11 15 16 17 18 25 36 37 45 46 55 56 57 65
67 69 75 76 77
VIN: WAUKF78E68A107783 Mileage: 204800km-127256miles
-------------------------------------------------------------------------------
Address 01: Engine Labels: 03G-906-016-BKD.clb
Part No SW: 03G 906 016 AL HW: 028 101 145 0
Component: R4 2,0L EDC G000SG 5249
Revision: 12345678 Serial number: XXXXXXXXXXXXXX
Coding: 0000072
Shop #: WSC 66565 257 00032
VCID: 6DD045BF74C262277C-8038
1 Fault Found:
17068 - Glow Plug Control Module (J179)
P0684 - 000 - Implausible Signal - MIL ON
Freeze Frame:
RPM: 0 /min
Torque: 56.0 Nm
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 11.32 V
Bin. Bits: 00001000
Temperature: 25.2°C
Bin. Bits: 01010000
Readiness: 0 0 0 1 0
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 8E0-910-517.clb
Part No SW: 8E0 910 517 J HW: 8E0 614 517 BH
Component: ESP8 quattro H06 0140
Revision: 00000000 Serial number: 00000000000000
Coding: 0004529
Shop #: WSC 06335 000 00000
VCID: 2E5282B3B944D93F05-807A
4 Faults Found:
01321 - Control Module for Airbags (J234)
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 25
Reset counter: 40
Time Indication: 0
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x4702
Hex Value: 0x0014
Hex Value: 0x20A6
Hex Value: 0x0001
18055 - Check Coding of ECUs on Powertrain Data Bus
P1647 - 000 -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 22
Reset counter: 40
Time Indication: 0
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x0702
Hex Value: 0x0014
Hex Value: 0x138E
Hex Value: 0x0001
01200 - ABS Valves Supply Voltage
000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 1
Fault Frequency: 1
Reset counter: 38
Time Indication: 0
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x0702
Hex Value: 0x0002
Hex Value: 0x8195
Hex Value: 0x0001
00526 - Brake Light Switch (F)
011 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00101011
Fault Priority: 2
Fault Frequency: 1
Reset counter: 38
Time Indication: 0
Freeze Frame:
Hex Value: 0x0000
Hex Value: 0x0702
Hex Value: 0x0004
Hex Value: 0xB094
Hex Value: 0x0001
-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 8E0-820-043.lbl
Part No: 8E0 820 043 BM
Component: A4 Klimaautomat 3233
Coding: 00000
Shop #: WSC 00000
VCID: 6DD045BF27C262277C-5140
3 Faults Found:
00716 - Air recirculation Flap Positioning Motor (V113)
41-00 - Blocked or No Voltage
00819 - High Pressure Sensor (G65)
07-10 - Signal too Low - Intermittent
00457 - Central Electronics Control Module / BCM (J519)
49-10 - No Communications - Intermittent
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 8E0-907-279-8EC.lbl
Part No: 8E0 907 279 N
Component: int. Lastmodul USA 0907
Coding: 10033
Shop #: WSC 06335
VCID: 3D70B5FF372232A78C-4B00
2 Faults Found:
01496 - Bulb for Fog-Lamps; Left (L22)
30-00 - Open or Short to Plus
01500 - Bulb for Fog-Lamps; Right (L23)
30-00 - Open or Short to Plus
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 8E0-959-655-94.lbl
Part No SW: 8E0 959 655 M HW: 8E0 959 655 M
Component: Airbag 9.41 H01 4240
Revision: 91H01424 Serial number: 003CS0000V2X
Coding: 0032607
Shop #: WSC 06335 000 00000
VCID: 4188C90F18DA5647E8-8014
Subsystem 1 - Part No: 8E0 910 339 D
Component: BF-Gewichtsens. H03 0080
Subsystem 2 - Serial number: 01KG0
Subsystem 3 - Serial number: 0001.01.0000H0300000000000ÿ†63
Subsystem 4 - Serial number: 000000ÿ†6332DRB40612072FGÿ†63
Subsystem 5 - Serial number: 2072FGÿ†6342DRB406060FAF-ÿ†63
Subsystem 6 - Serial number: 60FAF-ÿ†6352ARB402F8AC2A+ÿ†63
Subsystem 7 - Serial number: 8AC2A+ÿ†6362ARB402F6739D ÿ†63
Subsystem 8 - Serial number: 6739D ÿ†63729RB402B8361ESÿ†63
Subsystem 9 - Serial number: 8361ESÿ†63829RB402B835FD+ÿ
Subsystem 10 - Serial number: 835FD+ÿ
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 8E0-953-549.lbl
Part No: 8E0 953 549 Q
Component: Lenksáulenmodul 0801
Coding: 02142
Shop #: WSC 06335
VCID: 4188C90F4BDA5647E8-4B1A
1 Fault Found:
01304 - Radio
49-00 - No Communications
-------------------------------------------------------------------------------
Address 17: Instruments Labels: 8E0-920-9xx-8EC.lbl
Part No SW: 8E0 920 951 E HW: 8E0 920 951 E
Component: KOMBI+WFS 4 H14 0110
Revision: 0110 Serial number: 00000000000000
Coding: 0007008
Shop #: WSC 00590 210 88776
VCID: 2C5688BB8C58AB2F2B-5140
2 Faults Found:
00457 - Central Electronics Control Module / BCM (J519)
004 - No Signal/Communication - Intermittent
01304 - Radio
004 - No Signal/Communication
-------------------------------------------------------------------------------
Address 25: Immobilizer Labels: 8E0-920-9xx-8EC.lbl
Part No SW: 8E0 920 951 E HW: 8E0 920 951 E
Component: KOMBI+WFS 4 H14 0110
Revision: 0110 Serial number: 00000000000000
Coding: 0007008
Shop #: WSC 00590 210 88776
VCID: 2C5688BB8C58AB2F2B-5122
2 Faults Found:
00457 - Central Electronics Control Module / BCM (J519)
004 - No Signal/Communication - Intermittent
01304 - Radio
004 - No Signal/Communication
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels:. 8E0-959-433-MAX.clb
Part No: 8E0 959 433 CP
Component: Komfortgerát T7B 4336
Coding: 03870
Shop #: WSC 06335
VCID: 0108090F0B5A9647A8-4B00
Subsystem 1 - Part No: 8E1959801G
Component: Tõrsteuer.FS BRM 0706
Subsystem 2 - Part No: 8E1959802G
Component: Tõrsteuer.BF BRM 0706
Subsystem 3 - Part No: 8E0959801E
Component: Tõrsteuer.HL BRM 0606
Subsystem 4 - Part No: 8E0959802E
Component: Tõrsteuer.HR BRM 0606
6 Faults Found:
00955 - Key 1
35-10 - - - Intermittent
00457 - Central Electronics Control Module / BCM (J519)
49-10 - No Communications - Intermittent
01559 - Drivers Door
57-00 - Electric Circuit Failure
01560 - Passenger Door
57-00 - Electric Circuit Failure
01561 - Rear left door
57-00 - Electric Circuit Failure
01562 - Rear right door
57-00 - Electric Circuit Failure
-------------------------------------------------------------------------------
Address 65: Tire Pressure Labels: 8E0-907-273.lbl
Part No SW: 8E0 907 273 A HW: 8E0 907 273 A
Component: Reifendruck 3 H04 0130
Coding: 0062121
Shop #: WSC 06435 000 00000
VCID: 2A5A8EA386ACB51FD9-5140
No fault code found.
End-------------------------(Elapsed Time: 06:42)--------------------------