PASSAT B8 SW SIDE/LANE CHANGE ASSIST RETROFIT
- Thread starter sam1754
- Start date
- Joined
- May 27, 2017
- Messages
- 3,335
- Reaction score
- 2,086
- Location
- Finland
- VCDS Serial number
- C?ID=280813
I think Uwe has explained it numerous times why it does not have that feature. You’re not the first one to ask.
It’s better to do one thing properly than do multiple things bad. Try the other tool and you understand why. The user experience is shit. I mean real shit. Even ODIS has better interface and that is bad one.
I’ll take VCDS over any of those tools anytime for coding, adaptations and logging.
And isn’t it good that we have several different tools to use. Life would be boring if it would be ”one size fits all” philosophy?
It’s better to do one thing properly than do multiple things bad. Try the other tool and you understand why. The user experience is shit. I mean real shit. Even ODIS has better interface and that is bad one.
I’ll take VCDS over any of those tools anytime for coding, adaptations and logging.
And isn’t it good that we have several different tools to use. Life would be boring if it would be ”one size fits all” philosophy?
Yes indeed, I bought OBD11 thinking it should be more fun to code with an android machine but finally, I prefer take my computer and make things more clearly with VCDS, which I think is the best tool for codings and adaptation.
But, it doesn't allow me to do all I want!
But, it doesn't allow me to do all I want!
You're doing more than just "repairing" a car, no?I think Homer should be able to repair his car with only one wrenchBut I'm a little bit more demanding
-Uwe-
Where I can find this T7/T17 terminals?
Where I can find this T7/T17 terminals?
Hello, I'm enjoying lane assist retrofit and I'm willing to retrofit Side assist in addition.
I'm asking where to plug the thing above J533 on the picture below:
Where the RC32 goes?
- Joined
- May 27, 2017
- Messages
- 3,335
- Reaction score
- 2,086
- Location
- Finland
- VCDS Serial number
- C?ID=280813
From CAN gateway
- Joined
- May 27, 2017
- Messages
- 3,335
- Reaction score
- 2,086
- Location
- Finland
- VCDS Serial number
- C?ID=280813
You mean SC32? Fuse box inside dash, position 32
Thanks for the reply!
You do not need to go to the fuse box. You have only to find + for assitants (ACC, A5 camera...) which is above the driver's footwell. You'll find a convinience point where you can scratch cables and solder + cable for rear side assist controllers. It comes from T17h/15 ( a green/black cable). If you do it like this, you'll have it installed as per factory.
Last edited:
Hi
I buy from Ali wiring for side assist Tiguan and has wrong 8pin for radars
I buy from vw the right 8pin but my problem is at each other communication radars . It see only master but not slave
I buy from Ali wiring for side assist Tiguan and has wrong 8pin for radars
I buy from vw the right 8pin but my problem is at each other communication radars . It see only master but not slave
yes . i have the elsa wiring but i have isssue. i have not now to show full scan because i dont save it . i make coding to all ecu
the system saw the 3c but the only fault is "267010 databus
U1123 00 RECEIVED ERROR MESSAGE
FAULT SLAVE
my issue i beleive is at the wiring between the 2 radars . i cant understand 2 cables where is going
i have photos from radar terminal if can hellp me but how upload photos here?
Last edited:
- Joined
- May 27, 2017
- Messages
- 3,335
- Reaction score
- 2,086
- Location
- Finland
- VCDS Serial number
- C?ID=280813
can you explain how you connected them? I think I still have the wiring diagram for Tiguan as I’ve done the same retrofit to my Tiguan what you are now doing