Page 3 of 3 FirstFirst 123
Results 21 to 22 of 22

Thread: Need help! 04 Audi A8l won't start

  1. #21
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    17,368
    Post Thanks / Like
    T81/26=G70 (Mass Air Flow (MAF) Sensor). It draws large current or am i wrong? sorry I'm just learning lol
    Very good I'm proud of you OP!

    Did you know that no normally G70 it does NOT draw a significant amount of current, however, it makes me wonder why a 15 AMP fuse is used in WD for this and the consumers on the track in 87 and 87a huh, especially when those circuits which are burned are rated at 4 AMPS or less within the ECU, sigh?

    In addition to the aforementioned question, I'm still puzzled myself & further trying to understand why two separate heated OXS sensor supply fuses would be 15 Amp each too & when they only draw about an amp each & makes for no wonder why controllers are sacrificed?

    Did you trace everything on each consumer BUS and find out what is using the ECU as a fuse yet or did someone make a boo boo and induce this travesty of FOD?


    Also i just found out that the MAF sensor plug was unplug if that counts.
    Why was the MAF unplugged?


    Last edited by Jack@European_Parts; 12-09-2019 at 04:18 PM.
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  2. #22
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    17,368
    Post Thanks / Like
    Report?

    Any news




    FYI:

    When I extract the data in that old controller, there will indeed most likely be a forensic & of what happened before it went straight to DEAD!
    Last edited by Jack@European_Parts; Yesterday at 12:03 PM.
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •