Default Dashboard cluster turn off a3 8p

hi,
I have a problem with my audi a3 8p 2003 2.0tdi
Dashboard cluster constantly turn off (witch radio i must enter code) for few seconds. In 15 minute period it can turn off 5 times depends on weather (when colder it turn off more often, but it can be coincidence)
strange thing is when I start engine and do nothing dashboard cluster works fine but when i try to move dashboard cluster start to turn off

vcds : 18058

Please post an Auto-Scan for context.

-Uwe-

I will get back my diagnoistic cable in few weeks but cluster 17- instruments have no faulty only faulty code tied to cluster is 18058 p1650 - 000 -
I notice clsuter start turn off always when i move car and cluster always reset to the same time and trip odometer
is it posibble ecu has different data than cluster how to check it witch diagnostic cable ?
sorry for my english i not native speaker

It sounds to me like you have a connection problem if the cluster turns off when you move the car...

i checked wiring is ok,

That Auto-Scan Uwe asked to see needs to be your first step...

dark41 said:

i checked wiring is ok,

Click to expand...

take a look your message .....

cluster turn off when you move car ... so must be a vibation issue
how you check wires - look on it from 1m ?...come one
simple pull new wires (GND, KL30, KL15) ....COMPLETLY NEW ...to baypass old one
once you baypass old loom, you can say - is no wire issue
then look into cluster inside , or swap cluster

ok but if it is vibration it will hapen when i pull wire in cluster i tried and nothing hapened i will tray buy new wiring
but strange is that cluster works fine all the time when i start the car and dont move. when I move car cluster will start to reset even why I stop the car and for a while do nothing, if it is vibration or Soldering defects it will happen all the time thanks

You seem oddly reluctant to post an Auto-Scan though?

I think we should all wait for the Auto-Scan before making any further suggestions

it is all faulty codes some are because im recently have problem with accu winter and i dont use car often
i notice when i start car and cluster reset . cluster didnt rise mileage

Address 01: Engine
2 Faults Found:
18058 - Powertrain Data Bus
P1650 - 000 - Missing Message from Instrument Cluster - Intermittent
Freeze Frame:
RPM: 1680 /min
Torque: 0.0 Nm
Speed: 59.0 km/h
Load: 0.0 %
Voltage: 14.21 V
Bin. Bits: 00101000
Torque: 172.0 Nm
Torque: 0.0 Nm

17056 - Cylinder 2 Glow Plug Circuit (Q11)
P0672 - 000 - Electrical Fault
Freeze Frame:
RPM: 0 /min
Torque: 172.0 Nm
Speed: 0.0 km/h
Load: 0.0 %
Voltage: 11.40 V
Bin. Bits: 00101000
Temperature: 7.2°C
Bin. Bits: 00110000

Address 03: ABS Brakes

1 Fault Found:
01423 - Lateral Acceleration Sensor (G200)
005 - No or Incorrect Basic Setting / Adaptation

Address 08: Auto HVAC
0601 - Potentiometer On Positioning Motor for Central Flap (G112)
010 - Open or Short to Plus - Intermittent
Freeze Frame:
Fault Status: 00101010
Fault Priority: 3
Fault Frequency: 2
Reset counter: 160
Mileage: 202546 km
Time Indication: 0
Date: 2019.06.22
Time: 00:00:19

Freeze Frame:
Voltage: 14.40 V
(no units): 255.0
Temperature: 5.5°C

Address 09: Cent. Elect
1 Fault Found:
01341 - Control Module in Instrument Panel On Comfort CAN (J285)
004 - No Signal/Communication - Intermittent

Address 19: CAN Gateway

2 Faults Found:
00474 - Control Module for Immobilizer
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 2
Fault Frequency: 35
Reset counter: 163
Time Indication: 0
Date: 2019.06.22
Time: 00:32:27

00381 - Databus Instrument Cluster
014 - Defective - Intermittent
Freeze Frame:
Fault Status: 00101110
Fault Priority: 1
Fault Frequency: 18
Reset counter: 163
Time Indication: 15

Address 42: Door Elect, Driver

2 Faults Found:
00928 - Locking Module for Central Locking; Front Driver Side (F220)
008 - Implausible Signal - Intermittent
00105 - Signal Central Locking SAVE/LOCK Drivers Side
008 - Implausible Signal - Intermittent

Address 44: Steering Assist
1 Fault Found:
02546 - Steering Limit Stop
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Mileage: 2520 km
Temperature: 4.0°C
Voltage: 10.90 V
Voltage: 10.70 V

Address 52: Door Elect, Pass.

3 Faults Found:
00933 - Electric Window Motor; Passenger Side (V148)
005 - No or Incorrect Basic Setting / Adaptation - Intermittent
00929 - Locking Module for Central Locking; Front Passenger Side (F221)
008 - Implausible Signal - Intermittent
00106 - Signal Central Locking SAVE/LOCK Passenger Side
008 - Implausible Signal - Intermittent

Address 56: Radio
2 Faults Found:
01317 - Control Module in Instrument Cluster (J285)
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 5
Fault Frequency: 17
Reset counter: 163
Time Indication: 15

Freeze Frame:
Bin. Bits: 10

01299 - Diagnostic Interface for Data Bus (J533)
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 5
Fault Frequency: 1
Reset counter: 163
Time Indication: 15

We need full unedited autoscan.

I like that game

dark41 said:

Code:

Chassis Type: 8P (1K0)
Scan: 01 03 08 09 15 16 17 19 25 42 44 46 47 52 56 7D

VIN: WAUZZZ8PX4A0XXXXX                         Mileage: 202550km/125858miles

00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
03-ABS Brakes -- Status: Malfunction 0010
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: Malfunction 0010
25-Immobilizer -- Status: Sporadic communication error 1000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: Malfunction 0010
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: Malfunction 0010
56-Radio -- Status: Malfunction 0010
7D-Aux. Heat -- Status: OK 0000

Click to expand...

That's a gateway installation list.

We need the FULL UNEDITED AUTO-SCAN

-Uwe-