Hello,
I have this errors on CLIMATRONIC but I don't find anything on ross-tech fault codes list !!!
Is possible to explain me what SERVOMOTOR is broken because on the RIGHT SIDE I have no heat .
In fact I do not have heat on the ventilation grille from the door, but instead gives little heat on the middle one on the right side of the clock on board !!!
I understood from the ETKA program that Passat B8 have following SERVOMOTORS :
Pos. No.17 in ETKA
5Q0898141B or C = Adjuster unit
Pos. No.18 in ETKA
5Q0907511A = Servomotor
Pos. No.21 in ETKA
3Q0898141 = Adjuster unit
Pos. No.23 in ETKA
5Q0898511 = Control motor for temperature regulating flap
Pos. No.24 in ETKA
5Q0907511A = Servomotor
Pos. No.25 in ETKA
5Q0898511A = Control motor for temperature regulating flap
Pos. No.26 in ETKA
5Q0907511A = Servomotor
Pos. No.30 in ETKA
3Q0898141A = Adjuster unit
Pos. No.32 in ETKA
3Q189814 and 3Q2898141 = Adjuster unit
Pos. No.46 in ETKA
5Q0907511A = Servomotor
As you can see the code 5Q0907511A is identical to positions 18/24/26/46.
Now, which of these codes are on the left and which on the right I can only guess after the ETKA call.
But I don't know which piece is the defective one !!!
I be very grateful if, somebody tell me to which of them the three SERVOMOTORS refers to these two errors !!!
Thanks .
I have this errors on CLIMATRONIC but I don't find anything on ross-tech fault codes list !!!
Is possible to explain me what SERVOMOTOR is broken because on the RIGHT SIDE I have no heat .
In fact I do not have heat on the ventilation grille from the door, but instead gives little heat on the middle one on the right side of the clock on board !!!
I understood from the ETKA program that Passat B8 have following SERVOMOTORS :
Pos. No.17 in ETKA
5Q0898141B or C = Adjuster unit
Pos. No.18 in ETKA
5Q0907511A = Servomotor
Pos. No.21 in ETKA
3Q0898141 = Adjuster unit
Pos. No.23 in ETKA
5Q0898511 = Control motor for temperature regulating flap
Pos. No.24 in ETKA
5Q0907511A = Servomotor
Pos. No.25 in ETKA
5Q0898511A = Control motor for temperature regulating flap
Pos. No.26 in ETKA
5Q0907511A = Servomotor
Pos. No.30 in ETKA
3Q0898141A = Adjuster unit
Pos. No.32 in ETKA
3Q189814 and 3Q2898141 = Adjuster unit
Pos. No.46 in ETKA
5Q0907511A = Servomotor
As you can see the code 5Q0907511A is identical to positions 18/24/26/46.
Now, which of these codes are on the left and which on the right I can only guess after the ETKA call.
But I don't know which piece is the defective one !!!
Code:
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5G0-907-044.clb
Part No SW: 5G1 907 044 B HW: 5G1 907 044 B
Component: Climatronic H03 1001
Revision: 00001K10
Coding: 11020114202100012115504E00101102
Shop #: WSC 00015 115 08193
ASAM Dataset: EV_ACClimaBHBVW37X 003018
ROD: EV_ACClimaBHBVW37X_003_VW48.rod
VCID: 2708F3519F625D7FAB3-8072
Fresh Air Blower Front:
Geber für Kältemitteldruck/Kältemitteltemperatur:
Air quality sensor:
Relative humidity sensor in fresh air intake duct:
2 Faults Found:
328198 - Position Sensor for Right Temperature Flap Motor
B1095 11 [008] - Short to Ground
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 62384 km
Date: 2019.03.19
Time: 11:20:22
Voltage terminal 30: 14.4 V
Outside air temperature: 18.0 °C
Interior temperature: 26.7 °C
Right temperature flap: actual value: 0.0 %
Right temperature flap: actual value: 109
Right temperature flap: specified value: 109
328199 - Position Sensor for Right Temperature Flap Motor
B1095 15 [008] - Open or Short to Plus
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 106
Mileage: 62378 km
Date: 2019.03.19
Time: 10:33:35
Voltage terminal 30: 14.6 V
Outside air temperature: 13.5 °C
Interior temperature: 21.2 °C
Right temperature flap: actual value: 0.0 %
Right temperature flap: actual value: 221
Right temperature flap: specified value: 221
-------------------------------------------------------------------------------
I be very grateful if, somebody tell me to which of them the three SERVOMOTORS refers to these two errors !!!
Thanks .
Last edited by a moderator: