- Joined
- Oct 5, 2019
- Messages
- 15
- Reaction score
- 2
- Location
- USA, E Coast
- VCDS Serial number
- C?ID=381732
After receiving my VCDS i made an attempt to correct an (newly discovered after springs/struts) issue with my steering wheel not moving up / down (telescope is fine).
Steering Column Adjustment Prerequisites:
1.Steering Column or Central Electronics Control Module (J519) have been replaced or,
2.Approach and adjust all 4 end positions (up, down, forward, back).
[09 Central Electronics]
[04 Basic Settings] Group 001 [Go!]
Activate the Basic Setting. [ON/OFF/Next]
The adjustment should now be learned. adjust all 4 end positions (up, down, forward, back).
[Done, Go Back]
[Close Controller, Go Back - 06]
** HAVE NOW DISABLED POWER Steering Column Basic Setting - Group
** 001 – Disabled Voltage Supply (Terminal 30 left)
I have the following coding in [09] and am looking for help to get rid of the DIS warn.
all bulbs are tested and sockets are fresh.
I am wondering how to ENABLE voltage back to the Terminal 30 Left and confirm.
*hope this is the fix.
Steering Column Adjustment Prerequisites:
1.Steering Column or Central Electronics Control Module (J519) have been replaced or,
2.Approach and adjust all 4 end positions (up, down, forward, back).
[09 Central Electronics]
[04 Basic Settings] Group 001 [Go!]
Activate the Basic Setting. [ON/OFF/Next]
The adjustment should now be learned. adjust all 4 end positions (up, down, forward, back).
[Done, Go Back]
[Close Controller, Go Back - 06]
** HAVE NOW DISABLED POWER Steering Column Basic Setting - Group
** 001 – Disabled Voltage Supply (Terminal 30 left)
I have the following coding in [09] and am looking for help to get rid of the DIS warn.
all bulbs are tested and sockets are fresh.
I am wondering how to ENABLE voltage back to the Terminal 30 Left and confirm.
*hope this is the fix.
Code:
Saturday,28,September,2019,15:25:00:43223
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 19.6.1.0 (x64) HEX-V2 CB: 0.4508.4
Data version: 20190529 DS308.0
www.Ross-Tech.com
Mileage: 164640km-102302mi Repair Order:
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 4F0-910-279.lbl
Part No SW: 4F0 910 279 AE HW: 4F0 907 279 A
Component: ILM Fahrer H30 0390
Revision: 00000000 Serial number: 4F0907279
Coding: 0133122
Shop #: WSC 02335 785 00200
VCID: 6C81C4456A817A17061-8038
Subsystem 1 - Component: Fehler Lin-Slave 01
Subsystem 2 - Component: Fehler Lin-Slave 02
2 Faults Found:
01494 - Bulb for Parking Lamps; Left (M1)
011 - Open Circuit
Freeze Frame:
Fault Status: 01111011
Fault Priority: 2
Fault Frequency: 15
Reset counter: 110
Mileage: 163256 km
Time Indication: 0
Date: 2019.07.11
Time: 19:40:00
01498 - Bulb for Parking Lamps; Right (M3)
011 - Open Circuit
Freeze Frame:
Fault Status: 01111011
Fault Priority: 2
Fault Frequency: 1
Reset counter: 110
Mileage: 164620 km
Time Indication: 0
Date: 2019.09.27
Time: 09:18:00
-------------------------------------------------------------------------------