2016 GOLF R DQ500 BASIC SETTING ABORT ISSUE

   #1  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
Good Afternoon all.

I have a 2016 Golf R that I have swapped a DQ500 into. I have been fighting with issues for a long time on this car. finally was able to install a new mechtronics unit which leads me to my new issue.


When I try to perform basic setting for the transmission I get abort code 10. Anyone know what that is?

ign on
engine at idle
dsg fluid 65 deg c
parking brake on
vehicle level

start the adaptation and i get aborted safety reasons.

no fault codes.

attached is the auto scan and controller map. let me know if anyone could shed some light on this for me.

Thanks









Code:
Wednesday,28,August,2019,00:02:49:11506
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 19.6.1.0 (x64)
Data version: 20190529 DS308.0
www.Ross-Tech.com

Dealer/Shop Name: 3
VIN: WVWVF7AU0HW142856   License Plate: 


Chassis Type: AU-VW37 (5Q0)
Scan: 01 02 03 05 08 09 10 13 14 15 16 17 19 22 2B 3C 42 44 47 52
          55 5F 75 A5 A9

VIN: WVWVF7AU0HW142856   Mileage: 25462km-15821miles

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: Malfunction 0010
13-Auto Dist. Reg -- Status: Malfunction 0010
14-Susp. Elect. -- Status: OK 0000
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: Malfunction 0010
22-AWD -- Status: OK 0000
2B-Steer. Col. Lock -- Status: Malfunction 0010
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: Malfunction 0010
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: Malfunction 0010
55-Headlight Range -- Status: OK 0000
5F-Information Electr. -- Status: Malfunction 0010
75-Telematics -- Status: Malfunction 0010
A5-Frt Sens. Drv. Assist -- Status: Malfunction 0010
A9-Struct. Borne Sound -- Status: OK 0000
 
-------------------------------------------------------------------------------
Address 01: Engine (J623-CYFB)       Labels:. 06K-907-425-V1.clb
   Part No SW: 8V0 906 259 H    HW: 06K 907 425 E
   Component: 2.0l R4 TFSI  H13 I718  
   Revision: --H13---    
   Coding: 091D00122466000E3004
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_ECM20TFS0208V0906259H 001003
   ROD: EV_ECM20TFS0208V0906259H.rod
   VCID: 45818740C48D1467EA-8010

No fault code found.
Readiness: 1010 0101

-------------------------------------------------------------------------------
Address 02: Auto Trans (J743)       Labels:. 0BH-927-711.clb
   Part No SW: 0DL 300 043 T    HW: 0DE 927 711 
   Component: TVS DQ500     H12 9999  
   Revision: 00H12V32    
   Coding: 0014
   Shop #: WSC 00000 000 00000
   ASAM Dataset: EV_TCMDQ500021 001001
   ROD: EV_TCMDQ500021_001_VW37.rod
   VCID: 3E73E8ACA15B47BFAB-806A

No fault code found.

-------------------------------------------------------------------------------
Address 03: ABS Brakes (J104)       Labels: 5Q0-907-379-IPB-V1.clb
   Part No SW: 5Q0 614 517 CH    HW: 5Q0 614 517 AH
   Component: ESC           H62 0743  
   Revision: 00000000    Serial number: 63206000000865
   Coding: 01FA6BA15424096E457F030540C96980D62A90A2C0029637184050D8C2A8430000000012121212B835351919323200
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_Brake1UDSContiMK100IPB 036010
   ROD: EV_Brake1UDSContiMK100IPB_036_VW37.rod
   VCID: 79F93BB0F8F5A087DE-802C

4 Faults Found:
0128 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 1
                    Fault Frequency: 3
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 00:40:27

0297 - Steering Angle Sensor 
          B1168 F2 [008] - Not Initialized
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:23

4202 - Rear Right ABS Wheel Speed Sensor 
          C101D F1 [008] - Magnetic Field too Low
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 182
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:16:47

32928 - Function Restricted due to Insufficient Voltage 
          U1400 00 [009] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2019.01.17
                    Time: 01:45:40


-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. (J518)       Labels:| 5Q0-959-435.clb
   Part No SW: 5Q0 959 435 B    HW: 5Q0 959 435 
   Component: VWKESSYMQB    021 0710  
   Revision: 00021000    Serial number: 0423411988
   Coding: 032C0C
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_KessyHellaMQBAB 002019
   ROD: EV_KessyHellaMQBAB_002.rod
   VCID: 3B75E1B8B24952978C-806E

No fault code found.

-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255)       Labels:| 5G0-907-044.clb
   Part No SW: 5G0 907 044 CF    HW: 5G0 907 044 CF
   Component: Climatronic   H04 1801  
   Revision: 00001K08    
   Coding: 0002000420010000010500001251140A
   Shop #: WSC 12345 123 61029
   ASAM Dataset: EV_ACClimaBHBVW37X 006145
   ROD: EV_ACClimaBHBVW37X_006.rod
   VCID: 6DD11FE0BCBD0C2742-8038

   Fresh Air Blower Front: 

   Geber für Kältemitteldruck/Kältemitteltemperatur: 

   Air quality sensor: 

2 Faults Found:
262914 - Refrigerant Pressure 
          B10AB F0 [009] - Too Low
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 181
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:27

                    Outside air temperature: 28.5 °C
                    Engine speed: 0 /min
                    Compressor current: actual value: 0.000 A
                    Temperature after evaporator: 32.7 °C
                    System run time-Engine running time: 0 s
                    System run time-Terminal 15 on: 5 s

1048838 - Functional Limitation due to Energy Management 
          B10CD 00 [008] - -
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 2
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.14
                    Time: 18:06:58

                    Voltage terminal 30: 7.9 V
                    CAN input signal(s) status-Transport mode: On
                    CAN input signal(s) status-Static current measuring mode: OFF
                    CAN input signal(s) status-Windshield wiper: OFF
                    CAN input signal(s) status-Energy management deactivation stage: Deactivation stage 3
                    CAN input signal(s) status-Wipe wash: OFF
                    CAN input signal(s) status-Rear window heater actual value: OFF
                    CAN input signal(s) status-Back-up light: OFF
                    CAN input signal(s) status-Actual value of windshield heater: OFF


-------------------------------------------------------------------------------
Address 09: Cent. Elect. (J519)       Labels:| 5Q0-937-08X-HV1.clb
   Part No SW: 5Q0 937 085 BL    HW: 5Q0 937 085 AF
   Component: BCM MQBAB HNA H24 0175  
   Serial number: 01061631400540
   Coding: 00011B46C041A2E169E44000091407201800000000000000000000000000
   Shop #: WSC 12345 123 61029
   ASAM Dataset: EV_BCMMQB 015001
   ROD: EV_BCMBOSCH_015.rod
   VCID: 04075A448F37ED6FBD-8050

   Control Unit For Wiper Motor: 
   Subsystem 1 - Part No SW: 5G1 955 119 A    HW: 5G1 955 119 A  Labels: 5QX-955-119-V1.CLB
   Component: WWS    161024  043 0551 
   Serial number:         161107073447
   Coding: 0E4DDD

   Rain Light Recognition Sensor: 
   Subsystem 2 - Part No SW: 5Q0 955 547 B    HW: 5Q0 955 547 B  Labels: 5Q0-955-547.CLB
   Component: RLHS  042 0105 
   Serial number: S3Y16M11D21H10M36S25
   Coding: 00A8DD

3 Faults Found:
131330 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 4
                    Fault Frequency: 1
                    Reset counter: 223
                    Date: 2000.00.00
                    Time: 00:00:00

131586 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 4
                    Reset counter: 223

136458 - Terminal 15 
          B1148 15 [008] - Open or Short to Plus
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2019.01.17
                    Time: 01:45:35


-------------------------------------------------------------------------------
Address 10: Park/Steer Assist (J446)       Labels:| 5Q0-919-294.clb
   Part No SW: 5Q0 919 294 K    HW: 5Q0 919 294 A
   Component: PARKHILFE 8K  H03 0054  
   Revision: --------    Serial number: 39331631710835
   Coding: 0071155011
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_EPHVA18AU3700000 002026
   ROD: EV_EPHVA18AU3700000_002_VW37.rod
   VCID: 43859958CAB92A57C4-8016

4 Faults Found:
1113107 - Front Parking Aid Sensor(s) 
          B10FC 13 [008] - Open Circuit
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 180
                    Mileage: 25462 km
                    Date: 2018.11.27
                    Time: 05:19:05

13893632 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 3
                    Reset counter: 223

13637120 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 2
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:36:06

13637426 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:23


-------------------------------------------------------------------------------
Address 13: Auto Dist. Reg (J428)       Labels:| 3Q0-907-572.clb
   Part No SW: 5Q0 907 572 H    HW: 5Q0 907 572 H
   Component: ACC BOSCH MQB H10 0620  
   Coding: 350000C151FFC428949C810530301600000000000000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_ACCBOSCHVW416 002005
   ROD: EV_ACCBOSCHVW416_002_VW37.rod
   VCID: 3C77E2A4B74755AF85-8068

7 Faults Found:
2055 - Databus 
          U1122 00 [008] - Implausible Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:25

                    Control Module temperature: 33 °C
                    Voltage terminal 15: 13.0 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_irreversible error

0803 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 4
                    Fault Frequency: 2
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:24

                    Control Module temperature: 33 °C
                    Voltage terminal 15: 13.3 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_irreversible error

2086 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 2
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:36:06

                    Control Module temperature: 32 °C
                    Voltage terminal 15: 12.2 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_Off_MainSwitch_Off

2101 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 4
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:23

                    Control Module temperature: 33 °C
                    Voltage terminal 15: 12.9 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_StandBy

2067 - Databus 
          U1122 00 [008] - Implausible Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 26
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.11.27
                    Time: 05:45:55

                    Control Module temperature: 44 °C
                    Voltage terminal 15: 14.4 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_Off_MainSwitch_Off

2068 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 3
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.11.26
                    Time: 06:16:00

                    Control Module temperature: 29 °C
                    Voltage terminal 15: 14.6 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_irreversible error

1389 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 3
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:28:27

                    Control Module temperature: 31 °C
                    Voltage terminal 15: 7.0 V
                    Velocity_vehicle_reference: 0.00 m/s
                    Longitudinal_acceleration_vehicle_reference: 0.00 m/s²
                    Status_ACC_System: ACC_Init


-------------------------------------------------------------------------------
Address 14: Susp. Elect. (J250)       Labels: 5Q0-907-376.clb
   Part No SW: 5Q0 907 376 B    HW: 5Q0 907 376 A
   Component: DAEMPFUNGS-SG H17 0121  
   Serial number: 09101641350795
   ASAM Dataset: EV_DRCONTITEMIC 001019
   ROD: EV_DRCONTITEMIC_VW37.rod
   VCID: 387FFEB4837F798F61-806C

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags (J234)       Labels:| 5Q0-959-655.clb
   Part No SW: 5Q0 959 655 J    HW: 5Q0 959 655 J
   Component: AirbagVW20    010 0830  
   Serial number: 003GCR06HVJ2
   Coding: 8CCCFC00000000005000001AC24800000065
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_AirbaVW20SMEVW37X 002144
   ROD: EV_AirbaVW20SMEVW37X.rod
   VCID: 479D8D48FE81067718-8012

   Occupant Detection: 
   Subsystem 1 - Part No SW: 4M0 959 339 B    HW: 4M0 959 339 B
   Component: BF-Gewichtss.  H13 0022 
   Serial number: IBH00000000000602TKH
   Coding: 30324E

   Side Sensor Driver Front: 
   Subsystem 2 - Part No SW: -----------    HW: 480 001 711 16
   Component: SideSensor_Df  001 0887 
   Serial number: 35700000000060414F13
   Coding: 2D2D2D

   Side Sensor Passenger Front: 
   Subsystem 3 - Part No SW: -----------    HW: 480 001 211 16
   Component: SideSensor_Pf  001 0887 
   Serial number: 358000000006E1819F1S
   Coding: 2D2D2D

   Side Sensor Driver Rear: 
   Subsystem 4 - Part No SW: -----------    HW: 480 400 911 16
   Component: SideSensor_Dr  000 6149 
   Serial number: 3510001A72303C8133CV
   Coding: 2D2D2D

   Side Sensor Passenger Rear: 
   Subsystem 5 - Part No SW: -----------    HW: 480 401 211 16
   Component: SideSensor_Pr  000 6149 
   Serial number: 3520001C123B3B51653V
   Coding: 2D2D2D

   Front Sensor Driver: 
   Subsystem 6 - Part No SW: -----------    HW: 480 401 411 16
   Component: FrontSensor_D  000 6149 
   Serial number: 3550001B52303C82058U
   Coding: 2D2D2D

   Front Sensor Passenger: 
   Subsystem 7 - Part No SW: -----------    HW: 480 401 411 16
   Component: FrontSensor_P  000 6149 
   Serial number: 3560001B52303C83C35$
   Coding: 2D2D2D

1 Fault Found:
9483264 - Seat Occupied Recognition 
          B10B4 00 [008] - Function Restriction due to Undervoltage
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:28:34


-------------------------------------------------------------------------------
Address 16: Steering wheel (J527)       Labels:| 5Q0-953-549.clb
   Part No SW: 5Q0 953 507 HN    HW: 5Q0 953 549 E
   Component: Lenks. Modul  003 0140  
   Revision: --------    Serial number: 16111604220439
   Coding: 0C10
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_SMLSKLOMQB 020002
   ROD: EV_SMLSKLOMQB_020_VW37.rod
   VCID: 09194B70A815B007CE-805C

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments (J285)       Labels:| 5G0-920-XXX-17.clb-SRI3
   Part No SW: 5G1 920 858 B    HW: 5G1 920 858 B
   Component: KOMBI         304 8311  
   Coding: 0BAD081A7F88CF0502886B0B5400000000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_DashBoardVDDMQBAB 009051
   ROD: EV_DashBoardVDDMQBAB_009_VW37.rod
   VCID: 2F6DC5E87631BE3730-807A

1 Fault Found:
13635840 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 1
                    Reset counter: 223
                    Date: 2000.00.00
                    Time: 00:00:00


-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533)       Labels:| 5Q0-907-530-V1.clb
   Part No SW: 5Q0 907 530 AM    HW: 5Q0 907 530 F
   Component: GW MQB High   128 1265  
   Revision: --------    Serial number: 0005593897
   Coding: 0101000838085900FB00023A9C0F00000001050000000000000000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_GatewLear 013020
   ROD: EV_GatewLear_013.rod
   VCID: 7CF722A4F7C795AFC5-8028

   Alternator: 

   Multi Function Steering Wheel Control Module: 
   Subsystem 2 - Part No SW: 5G0 959 442 S    HW: 5G0 959 442 S  Labels: 3C8-959-537.CLB
   Component: E221__MFL-DC1  H11 0040 
   Serial number: 29160002086150076425
   Coding: 35FFFF

1 Fault Found:
1282 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 1
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2019.01.17
                    Time: 02:04:13

                    Supply voltage: Terminal 30: 8.4 V
                    Terminal 15: On


-------------------------------------------------------------------------------
Address 22: AWD (J492)       Labels:* 0CQ-907-554.clb
   Part No SW: 0CQ 907 554 H    HW: 0CQ 525 130 
   Component: Haldex4Motion H52 7083  
   Serial number: HA1-00018.10.16
   Coding: 0001
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_AllWheelContrHA1VW37X 004013
   ROD: EV_AllWheelContrHA1VW37X_004.rod
   VCID: 4A9BB47CED93FB1F07-801E

No fault code found.

-------------------------------------------------------------------------------
Address 2B: Steer. Col. Lock (J764)       Labels:* 5Q0-905-861.clb
   Part No SW: 5Q0 905 861 A    HW: 5Q0 905 861 A
   Component: ELV-MQBA      H01 0120  
   Revision: 00000000    Serial number: 16000194265006
   Coding: 5D00000000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_ELVMarquMQB 004111
   ROD: EV_ELVMarquMQB.rod
   VCID: 3467CA849F179DEF4D-8060

1 Fault Found:
13893632 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 8
                    Reset counter: 223
                    Date: 2000.00.00
                    Time: 00:00:00

                    ELV State: 04
                    Information Clamps: 00 00
                    CoCo State: E0 00
                    WFS State: 00 06
                    Vehicle speed: 655.33 km/h
                    Voltage: 35
                    AD-Value H-bridge: 18
                    Clamp15 flip flop: SSTx: button contacts: 06
                    CAN signals: 05


-------------------------------------------------------------------------------
Address 3C: Lane Change (J1086)       Labels:| 5Q0-907-686.clb
   Part No SW: 5Q0 907 686 B    HW: 5Q0 907 686 B
   Component: HRE_Master    H12 0071  
   Serial number: 0421291709
   Coding: 02011103
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_HREntryHella 001028
   ROD: EV_HREntryHella_VW37.rod
   VCID: 3C77E2A4B74755AF85-8068

   Lane Change Assistant 2: 
   Subsystem 1 - Part No SW: 5Q0 907 685 B    HW: 5Q0 907 685 B
   Component: HRE_Slave  H12 0071 
   Serial number: 0421356520          
   Coding: 020111

No fault code found.

-------------------------------------------------------------------------------
Address 42: Door Elect, Driver (J386)       Labels:| 5QX-959-X93-42.clb
   Part No SW: 5Q0 959 593 E    HW: 5Q0 959 593 B
   Component: TSG FS        020 0041  
   Serial number: 011116EK100027
   Coding: 003E13208000040000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_DCUDriveSideEWMAXKLO 006003
   ROD: EV_DCUDriveSideEWMAXCONT.rod
   VCID: 43859958CAB92A57C4-8016

   Drivers Door Rear Control Module: 
   Subsystem 1 - Part No SW: 5Q0 959 811     HW: 5Q0 959 811   Labels: 5QX-959-81X-V1.CLB
   Component: FOND_FHSG_DRV  005 0005 
   Serial number: 00000000000012353969
   Coding: 111000

4 Faults Found:
65548 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 5
                    Reset counter: 223
                    Date: 2000.00.00
                    Time: 00:00:00

65799 - Door Warning / Entry Lighting 
          B1775 01 [008] - Electrical Failure
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 1
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:36:04

65649 - Lamp for Ambient Illumination 
          B1325 13 [008] - Open Circuit
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 4
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:36:04

589829 - Window Regulator; Rear Driver side 
          B131F F5 [008] - Supply Voltage too Low
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 13
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 00:00:19


-------------------------------------------------------------------------------
Address 44: Steering Assist (J500)       Labels:| 5Q0-909-144.clb
   Part No SW: 3Q0 909 144 K    HW: 3Q0 909 144 H
   Component: EPS_MQB_ZFLS  506 5072  
   Coding: 9102
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_SteerAssisMQB 013144
   ROD: EV_SteerAssisMQB_013.rod
   VCID: 3A7BE4BCBD736B9F97-806E

3 Faults Found:
16272 - Steering Angle Sensor 
          B1168 F2 [008] - Not Initialized
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 1
                    Fault Frequency: 1
                    Reset counter: 187
                    Mileage: 0 km

                    Motor status: 00
                    System status: Reset
                    Supply voltage: 10.25 V
                    Temperature: 32.0 °C
                    KFC: 3F
                    KFA: 00 90
                    Environmental conditions: 21
                    uAdSensI_U1V2Filtered_gdu16: 1.20 V
                    uAdSensI_U5VFiltered_xdu16: 0.00000 V
                    uioUdNotFilt_xdu16: 10.13 V
                    uAdSensI_SwitchedKl30_xdu16: 10.10 V
                    NoInitCause_AsicSens: [0x12] ASC_CTRL_SAS_PERIOD_ERR - SASPERIOD content lost after last ignition off
                    NoInitCause_RackPos_Rohwert: 00 C0
                    RP_VALCNTSAV: not activated
                    RP_DIAGJOB: not activated
                    RP_RPS: not activated
                    RP_KMN_RACKPOS_SET: not activated
                    RP_STARTUP: not activated
                    RP_L2PLAUSI: not activated
                    RP_INDEXPLAUSI: not activated
                    RP_WHLSPDPLAUSI: not activated
                    RP_RUKUCNTR: not activated
                    RP_UNDERVOLT: activated
                    RP_CNTERR: activated

12289 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 2
                    Reset counter: 222
                    Date: 2000.00.00
                    Time: 00:00:00

                    Motor status: 00
                    System status: Reset
                    Supply voltage: 6.75 V
                    Temperature: 27.0 °C
                    KFC: 30
                    KFA: 00 01
                    Environmental conditions: 21
                    uAdSensI_U1V2Filtered_gdu16: 1.20 V
                    uAdSensI_U5VFiltered_xdu16: 0.00000 V
                    uioUdNotFilt_xdu16: 5.08 V
                    uAdSensI_SwitchedKl30_xdu16: 5.09 V
                    NoInitCause_AsicSens: [0x00] ASC_CTRL_SAS_NO_ERR
                    NoInitCause_RackPos_Rohwert: 00 00
                    RP_VALCNTSAV: not activated
                    RP_DIAGJOB: not activated
                    RP_RPS: not activated
                    RP_KMN_RACKPOS_SET: not activated
                    RP_STARTUP: not activated
                    RP_L2PLAUSI: not activated
                    RP_INDEXPLAUSI: not activated
                    RP_WHLSPDPLAUSI: not activated
                    RP_RUKUCNTR: not activated
                    RP_UNDERVOLT: not activated
                    RP_CNTERR: not activated

11776 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 2
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:29:46

                    Motor status: 00
                    System status: Waiting for start request
                    Supply voltage: 8.50 V
                    Temperature: 34.0 °C
                    KFC: 2E
                    KFA: 00 00
                    Environmental conditions: 21
                    uAdSensI_U1V2Filtered_gdu16: 1.20 V
                    uAdSensI_U5VFiltered_xdu16: 0.00000 V
                    uioUdNotFilt_xdu16: 8.81 V
                    uAdSensI_SwitchedKl30_xdu16: 8.82 V
                    NoInitCause_AsicSens: [0x00] ASC_CTRL_SAS_NO_ERR
                    NoInitCause_RackPos_Rohwert: 00 00
                    RP_VALCNTSAV: not activated
                    RP_DIAGJOB: not activated
                    RP_RPS: not activated
                    RP_KMN_RACKPOS_SET: not activated
                    RP_STARTUP: not activated
                    RP_L2PLAUSI: not activated
                    RP_INDEXPLAUSI: not activated
                    RP_WHLSPDPLAUSI: not activated
                    RP_RUKUCNTR: not activated
                    RP_UNDERVOLT: not activated
                    RP_CNTERR: not activated


-------------------------------------------------------------------------------
Address 47: Sound System (J525)       Labels:| 5Q0-035-456.clb
   Part No SW: 5Q0 035 456     HW: 5Q0 035 456 
   Component: MIB2_lite_amp H30 0150  
   Revision: 00000001    Serial number: VWZ8Z1GBA02SJAN
   Coding: 2200000000AAAAAA000000000000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_AMPMst12C1Gen2ALPI 001003
   ROD: EV_AMPMst12C1Gen2ALPI.rod
   VCID: 6DD11FE0BCBD0C2742-8038

1 Fault Found:
1539 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 8
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 01:02:24

                    Voltage terminal 30: 7.6 V


-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. (J387)       Labels:| 5QX-959-X92-52.clb
   Part No SW: 5Q0 959 592 E    HW: 5Q0 959 592 B
   Component: TSG BFS       020 0041  
   Serial number: 251016EJP23167
   Coding: 003E13208600040000800000
   Shop #: WSC 12345 123 61029
   ASAM Dataset: EV_DCUPasseSideEWMAXKLO 006003
   ROD: EV_DCUPasseSideEWMAXCONT.rod
   VCID: 428B9C5CD5A3235FCF-8016

   Passengers Rear Door Control Module: 
   Subsystem 1 - Part No SW: 5Q0 959 812     HW: 5Q0 959 812   Labels: 5QX-959-81X-V1.CLB
   Component: FOND_FHSG_PSG  005 0005 
   Serial number: 00000000000012039118
   Coding: 091000

3 Faults Found:
65548 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 5
                    Reset counter: 223
                    Date: 2000.00.00
                    Time: 00:00:00

65649 - Lamp for Ambient Illumination 
          B1325 13 [008] - Open Circuit
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 6
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:31:34

589845 - Window Regulator; Front Passenger side 
          B1320 F5 [008] - Supply Voltage too Low
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 2
                    Fault Frequency: 13
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 00:00:29


-------------------------------------------------------------------------------
Address 55: Headlight Range (J745)       Labels:| 7P6-907-357.clb
   Part No SW: 7P6 907 357 D    HW: 7P6 907 357 A
   Component: AFS-ECU       H07 0090  
   Revision: --------    Serial number: --------------
   Coding: 022202010B000400
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_HeadlRegulVWAFSMQB 001120
   ROD: EV_HeadlRegulVWAFSMQB.rod
   VCID: 408F9654DBAF314FD9-8014

   Left Headlamp Power Output Stage: 
   Subsystem 1 - Part No SW: 3D0 941 329 E    HW: 3D0 941 329 E  Labels: 3D0-941-329.CLB
   Component: LeiMo links  H01 0002 
   Coding: 2E0000

   Right Headlamp Power Output Stage: 
   Subsystem 2 - Part No SW: 3D0 941 329 E    HW: 3D0 941 329 E  Labels: 3D0-941-329.CLB
   Component: LeiMo rechts  H01 0002 
   Coding: 2E0000

No fault code found.

-------------------------------------------------------------------------------
Address 5F: Information Electr. (J794)       Labels:| 5G0-035-MIB-STD2.clb
   Part No SW: 3Q0 035 876 A    HW: 3Q0 035 876 A
   Component: MU-S-NS-US    840 0751  
   Serial number:               
   Coding: 027300020000000051220002001808009F0207F401200105C6
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_MUStd4CDELP 001001
   ROD: EV_MUStd4CDELP_VW37.rod
   VCID: 326BCC9C650393DF5F-8066

   Operating And Display Unit 1: 
   Subsystem 1 - Part No SW: 5GM 919 605     HW: 5GM 919 605 
   Component: ABT_Std-2_Nav  H50 4065 
   Serial number: VWZ6Z9S2501003      

   Data medium: 
   Subsystem 2 - Part No SW: 3G0 919 866 BB    HW: -----------
   Component: NAR 2017  --- 0525 
   Serial number: --------------------

2 Faults Found:
1539 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 5
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.14
                    Time: 01:13:22

                    Voltage terminal 30: 7.5 V

0020 - Tuner for Satellite Radio 
          B11CF 53 [009] - Deactivated
          Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 4
                    Fault Frequency: 1
                    Reset counter: 180
                    Mileage: 25462 km
                    Date: 2018.11.26
                    Time: 06:14:57

                    Voltage terminal 30: 14.6 V
                    SDARS_tuner_status_2-Satellite radio antenna status: Electrical OK
                    SDARS_tuner_status_2-Channel selection for satellite radio: 0
                    SDARS_tuner_status_2-Audio Signal: Available
                    SDARS_tuner_status_2-Antenna current: 132 mA
                    SDARS_tuner_status_2-Reception quality: optimum_signal
                    SDARS_tuner_status_2-Satellite radio tuner: pre-activation status: 07
                    SDARS_tuner_status_2-Satellite radio tuner: pre-activation value: 07


-------------------------------------------------------------------------------
Address 75: Telematics (J949)       Labels:| 5QE-035-285.clb
   Part No SW: 5QE 035 285 A    HW: 5QE 035 285 A
   Component: OCULowMQBUS   007 0570  
   Coding: 02730002C2821A017F1E06020000
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_OCULowMQB 001006
   ROD: EV_OCULowMQB.rod
   VCID: 43859958CAB92A57C4-8016

2 Faults Found:
13635840 - Supply voltage 
          U1011 00 [008] - Voltage too Low
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 3
                    Fault Frequency: 2
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2019.01.17
                    Time: 02:02:12

13893632 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 11
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.12
                    Time: 00:00:00


-------------------------------------------------------------------------------
Address A5: Frt Sens. Drv. Assist (R242)       Labels:| 3Q0-980-65X-A5.clb
   Part No SW: 3Q0 980 654 G    HW: 3Q0 980 654 
   Component: MQB_B_MFK     H06 0231  
   Serial number: 16111612P21265
   Coding: 0003070000000201002213548050490084000E100020
   Shop #: WSC 01357 011 00200
   ASAM Dataset: EV_MFKBoschMQBB 001001
   ROD: EV_MFKBoschMQBB_001_VW36.rod
   VCID: 3B75E1B8B24952978C-806E

2 Faults Found:
1123173 - Databus 
          U1123 00 [008] - Received Error Message
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 3
                    Reset counter: 222
                    Mileage: 25462 km
                    Date: 2018.11.26
                    Time: 06:14:51

                    Control Module temperature: 17 °C
                    Outside air temperature: 5.0 °C
                    Vehicle speed: 0.00 km/h
                    System run time: 605.0 s
                    Voltage terminal 15: 14.4 V
                    mid: 02 E0
                    Status of camera: operational
                    Engine_Running_Info: 1
                    Software_Info_4: 1
                    Software_Info_3: 3
                    Software_Info_2: 2
                    Software_Info_1: 0

262144 - Function Restricted due to Insufficient Voltage 
          U1400 00 [008] - -
          [New feature! Extended UDS fault detail is only supported by current gen. interfaces]
          Intermittent - Confirmed - Tested Since Memory Clear
             Freeze Frame:
                    Fault Status: 00000001
                    Fault Priority: 6
                    Fault Frequency: 3
                    Reset counter: 223
                    Mileage: 25462 km
                    Date: 2018.12.15
                    Time: 01:28:36

                    Control Module temperature: 32 °C
                    Outside air temperature: 25.5 °C
                    Vehicle speed: 0.00 km/h
                    System run time: 5.8 s
                    Voltage terminal 15: 6.9 V
                    mid: 00 05
                    Status of camera: operational
                    Engine_Running_Info: 0
                    Software_Info_4: 1
                    Software_Info_3: 3
                    Software_Info_2: 2
                    Software_Info_1: 0


-------------------------------------------------------------------------------
Address A9: Struct. Borne Sound (J869)       Labels: 4H0-907-159.clb
   Part No SW: 5G0 907 159 D    HW: 4H0 907 159 A
   Component: SAS-GEN 2     H07 0001  
   Serial number: 160930200242
   ASAM Dataset: EV_SoundActuaGen2AU64X 003010
   ROD: EV_SoundActuaGen2AU64X.rod
   VCID: 2F6DC5E87631BE3730-807A

No fault code found.

End---------------------(Elapsed Time: 05:41, udsna)-----------------------

Code:
Wednesday,28,August,2019,00:06:42:11506
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 19.6.1.0 (x64)
Data version: 20190529 DS308.0
www.Ross-Tech.com

Dealer/Shop Name: 3

VIN: WVWVF7AU0HW142856   License Plate: 
Mileage: 25462km-15821mi   Repair Order: 



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Gateway Installation List:  5Q0 907 530 AM

01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: Malfunction 0010
13-Auto Dist. Reg -- Status: Malfunction 0010
14-Susp. Elect. -- Status: OK 0000
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
22-AWD -- Status: OK 0000
2B-Steer. Col. Lock -- Status: Malfunction 0010
3C-Lane Change -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
47-Sound System -- Status: Cannot be reached 0100
52-Door Elect, Pass. -- Status: Malfunction 0010
55-Headlight Range -- Status: OK 0000
5F-Information Electr. -- Status: Malfunction 0010
75-Telematics -- Status: OK 0000
A5-Frt Sens. Drv. Assist -- Status: Malfunction 0010
A9-Struct. Borne Sound -- Status: OK 0000

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02: DTCs cleared
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE00001-Production mode,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE02332-Deactivate production mode,adapted from,00 00 00 ,to,00 00 00 ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE06425-Roller test bench mode: functional,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE00001-Production mode,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE00001-Production mode,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE00001-Production mode,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE06425-Roller test bench mode: functional,adapted from,not activated ,to,activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02: DTCs cleared
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02,0DL 300 043 T,channel IDE06425-Roller test bench mode: functional,adapted from,activated ,to,not activated ,

--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Address 02: DTCs cleared

Code:
 
   #2  

darkchina811

Verified VCDS User
Verified
Joined
Apr 14, 2018
Messages
950
Reaction score
564
Location
ITALY
VCDS Serial number
C?ID=333184
several modules are complaining about insufficient voltage. I would try to fix that first, then clear errors again and see what stays.
 
  • Like
Reactions: Uwe
   #3  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
several modules are complaining about insufficient voltage. I would try to fix that first, then clear errors again and see what stays.

Yes that was because the battery was dead. installed a new battery. just didn't clear the faults on that Auto scan.

All faults are now cleared.

could the abort be due to the hood being opened?
 
   #4  

kamold

Verified VCDS User
Verified
Joined
Mar 9, 2015
Messages
475
Reaction score
336
Location
Australia
VCDS Serial number
C?ID=241363
...thread hijack alert...

I'm having trouble running basic settings on my DQ500 retrofit also...it aborts with main reason 0 and sub reason 91.
Is anyone able to decode these status codes at all? For both OP and myself?
Mine happens at the point of clutch 1 closure so it looks like a problem with K1 clutch somewhere.
 
   #5  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
...thread hijack alert...

I'm having trouble running basic settings on my DQ500 retrofit also...it aborts with main reason 0 and sub reason 91.
Is anyone able to decode these status codes at all? For both OP and myself?
Mine happens at the point of clutch 1 closure so it looks like a problem with K1 clutch somewhere.


haha its all good.

I made sure all codes are clear and have a clean auto scan now.

closed the hood.

still have the same issue with aborting

main abort 0
sub 10
 
   #6  

NEtech

VCDS Distributor
VCDS Distributor
Joined
Feb 7, 2014
Messages
3,519
Reaction score
5,643
Location
Denmark
VCDS Serial number
C?ID=56995
You are looking at these Measurement values, while trying to do Basic Settings ?

IDE02775
IDE02824
IDE02825
 
   #7  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
You are looking at these Measurement values, while trying to do Basic Settings ?

IDE02775
IDE02824
IDE02825

Sorry for my ignorance but how do you watch the MVB While doing the Basic settings?
 
   #8  

NEtech

VCDS Distributor
VCDS Distributor
Joined
Feb 7, 2014
Messages
3,519
Reaction score
5,643
Location
Denmark
VCDS Serial number
C?ID=56995
While in Basic Settings, press the button [Show Measuring Data], enter the numbers, one at a time, 2775 2824 2825, in search box and select them.
 
   #9  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
While in Basic Settings, press the button [Show Measuring Data], enter the numbers, one at a time, 2775 2824 2825, in search box and select them.

I tried that and nothing shows up in the box after selecting any Chanel’s
 
   #10  

NEtech

VCDS Distributor
VCDS Distributor
Joined
Feb 7, 2014
Messages
3,519
Reaction score
5,643
Location
Denmark
VCDS Serial number
C?ID=56995
Start Basic Settings
 
   #11  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
I will do that this evening. what am I looking for exactly?

here is what i found before and after the basic setting

IDE02825 Substatus of abort code basic setting-Basic Settings Sub Status: 10
IDE02824 Main status of abort code basic setting-Basic Settings Main Status: 0
IDE02775 Status of basic setting data-State Of Basic Adjustmentdata: Invalid

also my fluid pressure is 1.2 bar is that normal
 
   #12  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
You are looking at these Measurement values, while trying to do Basic Settings ?

IDE02775
IDE02824
IDE02825

ok i just performed this and watched the channels

IDE02775 invalid
IDE02824 0 then goes to 2
IDE02825 0 then goes to 10 and aborts
 
   #13  

NEtech

VCDS Distributor
VCDS Distributor
Joined
Feb 7, 2014
Messages
3,519
Reaction score
5,643
Location
Denmark
VCDS Serial number
C?ID=56995
I guess you have looked at this ?
IDE02775 Is "invalid", so BS will not work, either procedure or some fault.

If you use the original tester, we maybe (or maybe not) get to know what "main reason 0" and "sub reason 10" means.
 
   #14  

kamold

Verified VCDS User
Verified
Joined
Mar 9, 2015
Messages
475
Reaction score
336
Location
Australia
VCDS Serial number
C?ID=241363
When I tried with that other tester it only gave me the same information - main reason and sub reason. I will try and run it again and then run GFF and see if it gives any more info
 
   #15  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
I guess you have looked at this ?
IDE02775 Is "invalid", so BS will not work, either procedure or some fault.

If you use the original tester, we maybe (or maybe not) get to know what "main reason 0" and "sub reason 10" means.

Yes I did see that post.

I assume the Invalid is my issue. I am trying to find someone with ODIS that can help me..
 
   #16  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
Ok I have an update. Seems that there is something incorrect with the TCU that I have. I have a Brand new RS3 mechatronics that I plugged in and when I check the data state of basic setting it reads Valid where the TCU from the swap Dq500 reads invalid.

So my question for the pros is can I install and adapt the Immobilizer from a Brand new Mechatronic unit from audi that is off of a VIN of an RS3 on this DQ500 in my GOLF R?

I know I would need a pass-thru device or ODIS.

Thanks
 
   #17  

jyoung8607

FoRT
Verified
Joined
Feb 25, 2014
Messages
2,780
Reaction score
4,490
Location
Cincinnati, OH
VCDS Serial number
C?ID=25607
I don't think the TCU is an Immobilizer participant. You could certainly have Component Protection, but many people report success removing CP with ODIS even in weird retrofit situations, provided you don't try to set/restore things like coding and parameterization at the same time.
 
   #18  

kamold

Verified VCDS User
Verified
Joined
Mar 9, 2015
Messages
475
Reaction score
336
Location
Australia
VCDS Serial number
C?ID=241363
In MQB the transmission needs to be unlocked with ODIS online if swapped.
You can flash it to appropriate software version or use custom which I guess you already had in mind.
 
   #19  

JRMS

Verified VCDS User
Verified
Joined
Jul 22, 2019
Messages
14
Reaction score
4
Location
NJ, USA
VCDS Serial number
C?ID=362617
In MQB the transmission needs to be unlocked with ODIS online if swapped.
You can flash it to appropriate software version or use custom which I guess you already had in mind.

ok great, yes Using custom software. Thank you.
 
   #20  

jyoung8607

FoRT
Verified
Joined
Feb 25, 2014
Messages
2,780
Reaction score
4,490
Location
Cincinnati, OH
VCDS Serial number
C?ID=25607
I don't think the TCU is an Immobilizer participant. You could certainly have Component Protection, but many people report success removing CP with ODIS even in weird retrofit situations, provided you don't try to set/restore things like coding and parameterization at the same time.
Correcting myself here, having recently re-read SSP 517, page 42 regarding Immobilizer V shows the DSG mechatronic is now a participant in the Immobilizer scheme.
 
Back
Top