Page 5 of 6 FirstFirst ... 3456 LastLast
Results 41 to 50 of 52

Thread: 10530 - EVAP System P0456 00 [096] - Very Small Leak Detected

  1. #41
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,849
    Post Thanks / Like
    Is your car with FOD modified tuning like prior OP of thread?

    Did you perform pinch isolation tests with mighty vac yet?
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  2. #42
    Verified VCDS User
    Join Date
    Nov 2018
    Location
    USA
    Posts
    19
    Post Thanks / Like
    My car is completely stock since I bought it new.

    I'm not familiar with the pinch isolation test. Can you provide a link or tell me where to look for such a procedure?

  3. #43
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,849
    Post Thanks / Like
    Did you consider the repair manual and common sense plus using pinch clamps or rubber caps to isolate zone by zone with a mighty vac tester?

    Ever soap suds on a covered engine bay & to watch the suck in or blow off for indication of the aforementioned?

    Ever give an engine a shaving cream whippet for a close shave in the thick needed hotter areas?
    Last edited by Jack@European_Parts; 07-13-2020 at 06:08 AM.
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  4. #44
    Verified VCDS User
    Join Date
    Nov 2018
    Location
    USA
    Posts
    19
    Post Thanks / Like
    Quote Originally Posted by Jack@European_Parts View Post
    Did you consider the repair manual and common sense plus using pinch clamps or rubber caps to isolate zone by zone with a mighty vac tester?

    Ever soap suds on a covered engine bay & to watch the suck in or blow off for indication of the aforementioned?

    Ever give an engine a shaving cream whippet for a close shave in the thick needed hotter areas?
    I haven't tried any of that stuff, and the comment about "common sense" is frankly a bit harsh. I'm sure you are very knowledgable, but it really rubs people the wrong way. Maybe you're trying to be helpful, but you really should consider a different approach to expressing yourself.

    My question is whether or not the TSB I found applies to this code. If Audi has already found a solution to this code, I think I would just go with their instructions.

    If ANYONE ELSE other than Jack can assist, please do. I'm not looking for another verbal beating from Jack.

  5. #45
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,849
    Post Thanks / Like
    I haven't tried any of that stuff, and the comment about "common sense" is frankly a bit harsh. I'm sure you are very knowledgable, but it really rubs people the wrong way. Maybe you're trying to be helpful, but you really should consider a different approach to expressing yourself.

    My question is whether or not the TSB I found applies to this code. If Audi has already found a solution to this code, I think I would just go with their instructions.

    If ANYONE ELSE other than Jack can assist, please do. I'm not looking for another verbal beating from Jack.



    I'm sorry I thought I added these links before below, are you saying you are working without RTFB?

    Search the how too section on evap because the link doesn't show correctly.

    "Common sense" as in DO NOT use pinch clamp/pliers on hard plastic that can be brittle and break, use vacuum RUBBER caps at zones to seal as alternate because some other schmuck didn't I asked you use it..... sorry for looking out for you, okay?

    LDP)-Test&p=130741&viewfull=1#post130741" target="_blank">https://forums.ross-tech.com/showthr...l=1#post130741

    https://forums.ross-tech.com/showthr...ou!-Air-leaks!

    https://forums.ross-tech.com/showthr...l=1#post171228


    You need to calm down and RTFB and do mechanical tests and not focus on a magic answer!

    Last edited by Jack@European_Parts; 07-13-2020 at 05:39 PM.
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  6. #46
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,849
    Post Thanks / Like
    Perspective by hieroglyphics.

    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  7. #47
    Verified VCDS User
    Join Date
    Nov 2018
    Location
    USA
    Posts
    19
    Post Thanks / Like
    Thanks I appreciate the effort.

  8. #48
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    19,849
    Post Thanks / Like
    See there you go glad you found it helpful.

    The EVAP thread every time I copy the link it fails but it can be searched in how too section. No one ever put in super sticky, Uwe will most likely read this and do that.
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  9. Likes Uwe liked this post
  10. #49
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    28,838
    Post Thanks / Like
    Blog Entries
    1
    Quote Originally Posted by Jack@European_Parts View Post
    The EVAP thread every time I copy the link it fails but it can be searched in how too section. No one ever put in super sticky, Uwe will most likely read this and do that.
    You mean this thread? Done!

    -Uwe-
    Lock-down of sick people: Quarantine
    Lock-down of healthy people: Tyranny

  11. #50
    Benevolent Dictator Uwe's Avatar
    Join Date
    Jan 2014
    Location
    Earth
    Posts
    28,838
    Post Thanks / Like
    Blog Entries
    1
    Quote Originally Posted by Jack@European_Parts View Post
    The EVAP thread every time I copy the link it fails but it can be searched in how too section. No one ever put in super sticky, Uwe will most likely read this and do that.
    You mean this thread? Done!

    -Uwe-
    Lock-down of sick people: Quarantine
    Lock-down of healthy people: Tyranny

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •