Hi,
i buyed VCDS HEX.NET to configure my 3 Audi A2 3L and get infos about all the sickness that these cars would like to have
I´ve got problems by using VCDS mobile (like to use at the car by iPad or iPhone) NO Values, vs. VCDS (using in the home office), running fine and shows correct values.
my config (Sorry, it´s not possible to use a local file):
CB: 0.4437
FW: 0.254
CFB:0.10
BL: 0.28
DS: 60000055
The VCDS found regarding:
Autoscan VCDS DRV 18.9
Adresse 02: Getriebe Labeldatei: DRV\6N0-927-735.lbl
Teilenummer: 6N0 927 735 D
Bauteil: DS085 Getriebe 3081
Codierung: 00000
Betriebsnr.: WSC 00000
VCID: B93AA50AA1CE79825A-0964
otherwise:
Autoscan VCDSmobile:
Address 02: Auto Trans (J743) Labels: 0B-02.lbl
Part No SW: 0BT 300 011 S HW: 0BH 927 711 G
Component: DSG DQ500-7A H11 5205
Revision: 00H11V01
Coding: 0014
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_TCMDQ500021 001001
ROD: EV_TCMDQ500021_VW36.rod
VCID: 3E3FADFB36F63D836B6FACFBC7-806B
So, I think thats the problem that I´did´nt see the values under:
Select --> Common --> 02-Auto Trans --> Functions --> Advanced Measuring Values -->
selected:
Engine Load (via CAN) [loc 2-1]
Clutch Travel Sensor (G162) [loc 2-2]
Voltage (Terminal 15) [loc 2-3]
Coolant Temperature (G62) [loc 2-4
--> Submit there are no values !
The same should be happen to 025 Immobilizer
because the Shopnumber is 0,
(but if u select it under VCDS it´s refer to 017!)
U will find infos about the gear:
http://wiki.ross-tech.com/wiki/index.php/5-Speed_Electronic_Manual_Transmission_(085)
I´ved updated the firmware of the HEX-NET, but that did´nt solved the problem.
Is there a kind of roadmap (pls give me a link) where i can see, when these dates will be included to VCDS mobile.
These dates are very urgend to give the 3L cars of Audi a chance to survife and make VCDS mobile great for using.
best regards
BerndJ
i buyed VCDS HEX.NET to configure my 3 Audi A2 3L and get infos about all the sickness that these cars would like to have
I´ve got problems by using VCDS mobile (like to use at the car by iPad or iPhone) NO Values, vs. VCDS (using in the home office), running fine and shows correct values.
my config (Sorry, it´s not possible to use a local file):
CB: 0.4437
FW: 0.254
CFB:0.10
BL: 0.28
DS: 60000055
The VCDS found regarding:
Autoscan VCDS DRV 18.9
Adresse 02: Getriebe Labeldatei: DRV\6N0-927-735.lbl
Teilenummer: 6N0 927 735 D
Bauteil: DS085 Getriebe 3081
Codierung: 00000
Betriebsnr.: WSC 00000
VCID: B93AA50AA1CE79825A-0964
otherwise:
Autoscan VCDSmobile:
Address 02: Auto Trans (J743) Labels: 0B-02.lbl
Part No SW: 0BT 300 011 S HW: 0BH 927 711 G
Component: DSG DQ500-7A H11 5205
Revision: 00H11V01
Coding: 0014
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_TCMDQ500021 001001
ROD: EV_TCMDQ500021_VW36.rod
VCID: 3E3FADFB36F63D836B6FACFBC7-806B
So, I think thats the problem that I´did´nt see the values under:
Select --> Common --> 02-Auto Trans --> Functions --> Advanced Measuring Values -->
selected:
Engine Load (via CAN) [loc 2-1]
Clutch Travel Sensor (G162) [loc 2-2]
Voltage (Terminal 15) [loc 2-3]
Coolant Temperature (G62) [loc 2-4
--> Submit there are no values !
The same should be happen to 025 Immobilizer
because the Shopnumber is 0,
(but if u select it under VCDS it´s refer to 017!)
U will find infos about the gear:
http://wiki.ross-tech.com/wiki/index.php/5-Speed_Electronic_Manual_Transmission_(085)
I´ved updated the firmware of the HEX-NET, but that did´nt solved the problem.
Is there a kind of roadmap (pls give me a link) where i can see, when these dates will be included to VCDS mobile.
These dates are very urgend to give the 3L cars of Audi a chance to survife and make VCDS mobile great for using.
best regards
BerndJ