Hello friend , is possible start stop system settings in infotainment drive mode selection sport / eco /individua/deactivation start stop system? On mqb platform? Thanks for answers
Last edited:
Start/stop system in drive mode selection menu
- Thread starter adejme
- Start date
I doubt it can be done. what car does the picture come from?
- Joined
- Dec 16, 2014
- Messages
- 7,989
- Reaction score
- 7,823
- Location
- Westbury, UK
- VCDS Serial number
- C?ID=1423
It certainly doesn't appear in the Individual menu on my MQB platform Skoda Octavia - nor can I see any adaptation channels to enable it...
A full Auto-Scan of the car pictured in the first post would be useful.
A full Auto-Scan of the car pictured in the first post would be useful.
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
^^^ Dave:I agree -there is only one way to "manually" enable/deactivate SS on an MQB vehicle, and that way is to earth the appropriate BCM pin (which is T73c/ 60 on a mk7) -SS is actually triggered by the leading/trailing edge of the falling/rising voltage on the BCM pin.
Of course there is always the "unofficial" way which is to fool SS system be tweaking operational criteria like "temperature" and "voltage" thresholds . Happy to be told otherwise
Don
Of course there is always the "unofficial" way which is to fool SS system be tweaking operational criteria like "temperature" and "voltage" thresholds . Happy to be told otherwise
Don
- Joined
- Dec 16, 2014
- Messages
- 7,989
- Reaction score
- 7,823
- Location
- Westbury, UK
- VCDS Serial number
- C?ID=1423
That's very true, but not all that adejme is asking...
He also wants to know whether a setting to enable/disable start/stop can be added into the Individual menu on the infotainment system on an MQB platform car.
What can be modified via driving profiles is stored in the Gateway's parameters. Unfortunately nothing you can change with VCDS.
Seems someone has modified those so Start/Stop can be shown there. Maybe someone inform "meich" to have a look at this, since he is working on similiar stuff (https://www.facebook.com/mqbcoding/photos/a.830666343659925/2199425033450709/?type=3&theater).
Edit: linked this thread under this Facebook post for the greater good.
Seems someone has modified those so Start/Stop can be shown there. Maybe someone inform "meich" to have a look at this, since he is working on similiar stuff (https://www.facebook.com/mqbcoding/photos/a.830666343659925/2199425033450709/?type=3&theater).
Edit: linked this thread under this Facebook post for the greater good.
Unfortunately i do not have full autoscan from this vehicle ,i found it on one forum , one person told me it is possible but it does not give instructions. You think, where where i could find some settings ? Can gateway parameters start stop with Vag can pro is possible ? thanks
it's probably all about loading a modified firmware to the gateway. VCDS cannot flash modules, and we don't have answers (obviously) for other cables.
- Joined
- May 16, 2014
- Messages
- 5,469
- Reaction score
- 5,935
- Location
- Melbourne, Australia
- VCDS Serial number
- C?ID=194404
^^ hmm............. yes, it's clearly possible to "modify" the SS disable trigger on a MQB vehicle via the OBD port (see HERE) - so presumably some form of CAN message can be sent to one of the control modules for this purpose (sans firmware modification). BUT - this is very different to sending the command via the MIB (which I presume would involve setting-up a user-interface as well as the requisite CAN messages.
mmm, indeed. when I retrofitted ACC, I enabled one bit FPA_MO_IDon'tRemember to have ACC show up into driving profiles...
When i have a vehicle, I will try it out ,All steps can be undone without damaging the gateway ? thanks
Yes. The FPA Bits are reversible
Today i check all bits FPA and fpa_mo_stst is active i do not in drive mode :/