Hello guys,
I own a 2015 VW Golf 7R DQ250 that has been recently converted to a DQ500 RS3 facelift gearbox.
I noticed the following error message on the gearbox a few days ago, and wanted to ask if somebody can help me shed some light into this topic?
Also, I would like to note that I noticed oil coming out of the gearbox air breather, due to excessive launches and hard driving I believe.
Is this common on DQ500?
I confirm that the gearbox is running stage 3+ or stage4 software and it is quite aggresive with high clutch pressure that should hold up to 800 NM of torque without issues.
-------------------------------------------------------------------------------
Address 02: Auto Trans (J743) Labels:. 0BH-927-711.clb
Part No SW: 0DL 300 043 T HW: 0GC 927 711 G
Component: DQ500 H06 9999
Revision: 00H06V07
Coding: 0014
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_TCMDQ500021 001001
ROD: EV_TCMDQ500021.rod
VCID: 3E263775A0FFCE77AC1-806A
1 Fault Found:
10908 - ROD - Unknown Error Code
- 00 [040]
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 0
Fault Frequency: 1
Mileage: 25922 km
Date: 2019.03.07
Time: 13:01:01
Engine speed: 1113.00 /min
Vehicle speed: 0 km/h
Coolant temperature: 88 °C
Clutch: primary stat: Neutral
selected gear: GANG_R
Driving position: P
Engine torque: -16 Nm
Control Module temperature: 72 °C
Accelerator position: 14.8 %
DTC memory status: 50
-------------------------------------------------------------------------------
Also, a pic of the gearbox breather covered in oil.
https://ibb.co/5xr8M34
Thank you!
I own a 2015 VW Golf 7R DQ250 that has been recently converted to a DQ500 RS3 facelift gearbox.
I noticed the following error message on the gearbox a few days ago, and wanted to ask if somebody can help me shed some light into this topic?
Also, I would like to note that I noticed oil coming out of the gearbox air breather, due to excessive launches and hard driving I believe.
Is this common on DQ500?
I confirm that the gearbox is running stage 3+ or stage4 software and it is quite aggresive with high clutch pressure that should hold up to 800 NM of torque without issues.
-------------------------------------------------------------------------------
Address 02: Auto Trans (J743) Labels:. 0BH-927-711.clb
Part No SW: 0DL 300 043 T HW: 0GC 927 711 G
Component: DQ500 H06 9999
Revision: 00H06V07
Coding: 0014
Shop #: WSC 00000 000 00000
ASAM Dataset: EV_TCMDQ500021 001001
ROD: EV_TCMDQ500021.rod
VCID: 3E263775A0FFCE77AC1-806A
1 Fault Found:
10908 - ROD - Unknown Error Code
- 00 [040]
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 0
Fault Frequency: 1
Mileage: 25922 km
Date: 2019.03.07
Time: 13:01:01
Engine speed: 1113.00 /min
Vehicle speed: 0 km/h
Coolant temperature: 88 °C
Clutch: primary stat: Neutral
selected gear: GANG_R
Driving position: P
Engine torque: -16 Nm
Control Module temperature: 72 °C
Accelerator position: 14.8 %
DTC memory status: 50
-------------------------------------------------------------------------------
Also, a pic of the gearbox breather covered in oil.
https://ibb.co/5xr8M34
Thank you!
Last edited by a moderator: