Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: Audi a1 halogeen to bi-xenon long coding help

  1. #11
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    Quote Originally Posted by m87a View Post
    in that case go to 44 enter security access go to basic setting and do g85, after that full lock steering wheel left hold it then right, that should sort it out, on mk7 sometimes it takes couple of tries.
    Never had issue with xenon retrofit with or without level control / AFS causing dtc on abs.
    With kufatec adapter were there addition wires required to run to bcm, did you connect them?
    thanks
    yes i did connect the 2 kufatec wires in the bcm

  2. #12
    Verified VCDS User
    Join Date
    Jan 2015
    Location
    Bosnia and Herzegovina
    Posts
    551
    Post Thanks / Like
    did you check if your bcm has these 2 pins present, in most cases these 2 additional wires are either for bi xenon solenoids or drl light.

  3. Likes rostel liked this post
  4. #13
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    Quote Originally Posted by m87a View Post
    did you check if your bcm has these 2 pins present, in most cases these 2 additional wires are either for bi xenon solenoids or drl light.

    the PINs at the BCM where not wired , i wired them at the C and A connetor pin numbers i have to check

  5. #14
    Verified VCDS User
    Join Date
    May 2016
    Location
    Netherlands
    Posts
    132
    Post Thanks / Like
    Need 4 wires.
    C 26 48 49 and A44

    Then need coding and also bcm support

  6. Likes rostel liked this post
  7. #15
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    Quote Originally Posted by vastechnics View Post
    Need 4 wires.
    C 26 48 49 and A44

    Then need coding and also bcm support
    thanks
    where can i get the correct information for it

  8. #16
    Verified VCDS User
    Join Date
    May 2016
    Location
    Netherlands
    Posts
    132
    Post Thanks / Like
    What correct info you mean

  9. Likes rostel liked this post
  10. #17
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    i wil check tomorrow if the other pins are wired

  11. #18
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    Quote Originally Posted by vastechnics View Post
    Need 4 wires.
    C 26 48 49 and A44

    Then need coding and also bcm support
    48 and 49 are not wired
    do I also have to swap some wires to those pins? Or do I have to rewire them to the headunit ? (I have read A5 toC48 and C46 to C49 on a audi forum ) ?

    thanks
    Last edited by rostel; 01-21-2019 at 12:34 PM.

  12. #19
    Verified VCDS User
    Join Date
    Jan 2019
    Location
    Netherlands
    Posts
    12
    Post Thanks / Like
    thanks for the information it works

  13. Likes Uwe liked this post

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •