Page 3 of 3 FirstFirst 123
Results 21 to 23 of 23

Thread: Who wants to dwell over or DUAL on x2 N80 function & helpful mods/SMOG reduced?

  1. #21
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,546
    Post Thanks / Like
    Brake Booster line mock up, brackets, anti chafe provisions, clamps and landed!

    Clamp at pro vent TBD in process!
    Clamp at fire wall and fan control unit landed, moving flexibility point by braided rubber line reinforced with internal spring wound!
    Verify possible clearance chafe point at strut tie bar check!



    Chafe selves added to braided hose!
    Flat extension bracket determined in front of pro vent to add stability with chafe sleeves in process.


    Booster circuit and forward bracket complete with notch for clamp all stuff painted it's a wrap for brake booster!

    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  2. Likes jyoung8607, Uwe, NZDubNurd, PetrolDave, D-Dub liked this post
  3. #22
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,546
    Post Thanks / Like
    SAT update........SUMP MOD!

    Pro vent drain to SUMP add addition with pipe to integrated baffle labyrinth in oil pan "grid" trap door design not shown.

    Run and route hose from Provent in process still for additional two brackets TBD @ Trans case.

    Start FAB on the fly........

    REMOVE lower stress bar and dog bone drain oil and remove turbo return line.

    REMOVE PAN FOR QT INSPECTION OF GIRDLE AND OIL QUALITY & TOO VACATE ASSEMBLY PASTES. CHECK!



    DRILL HOLE IN PAN AND BEND PIPE LEFT OVER FROM CHINA TOILET PAPER HOLDER & TO MAKE USE OF SCRAP WHICH IS NOW A RACE CAM BRAKE ROTOR TOILET PAPER HOLDER.
    WELD IN PLACE FREE HAND BRACKET TO HOLD FOR VIBRATION.

    MIGHTY VAC THE LINE AFTER WELD AND PAINT ....CHECK!
    INSTALL PAN TEST FIT WITH GRID .....CHECK



    VERIFY RETURN LINE AND CUT TO ESTIMATE ROUTING FROM MANN PRO VENT........CHECK.
    LAND FASTENERS......

    HOSE TYPE DOUBLE BRAIDED ATF AND DIESEL TYPE TO NOT REACT!




    THAT'S IT FOR TODAY......BEAT!
    SAMS CLUB RUN AND TIME FOR COCKTAILS AND DEBRIEFING!
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  4. Likes jyoung8607, Uwe, D-Dub liked this post
  5. #23
    NostraJackAss Jack@European_Parts's Avatar
    Join Date
    Jan 2014
    Location
    1001 State Route 17K Montgomery New York 12549
    Posts
    16,546
    Post Thanks / Like
    OKAY TODAY'S REPORT ON LOWER TURBO BRACKET SUPPORT I ALWAYS SEEM TO SEE NEGATED!


    SOME ROUND STOCK AND PLATE + CONSIDERING MOUNT OPTIONS STRAIGHT VS TRIANGULATED


    TRIANGULATED IT IS...... TACK UP IN PLACE!



    CHECKING FITMENT AND TEST COVER CLEARANCE FOR CUSTOM CV HEAT SHIELD





    TAKE BACK APART AND MEASURE NEW HARDWARE AND PAINT WITH HIGH HEAT WURTH PAINT!




    IT'S A WRAP FOR TODAY!
    European Parts Emporium/Performance / Immobilizer Solutions EPE
    Certified Master Trained NY/BAR/BAD 7076062/ASE/SAE/NASTF Legal Factory Authorized/Licensed GeKo/FaZit # 403738
    Specializing in Custom Services IE: "welding-fabrication" / EPA-SMOG Update or Pass-Thru-Programming / Data Transfer / Immobilizers & OEM Quality Parts
    Above Magic! No Written record, AUTO-SCAN or Appointment = NO HELP!
    www.FixMyEuro.com <<<<<CLICK HERE! or vwemporium@aol.com ( JPPSG & Unverified members need not PM me & Please don't email or call facility for free tech support...use the forum )
    Getting you CONTROL again of your property - TAKE IT! In Conjunction with.........

  6. Likes Uwe, jyoung8607, NZDubNurd, PetrolDave liked this post

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •