Drowned KESSY Module - 2013 VW Phaeton
- Thread starter walters_c
- Start date
- Joined
- Apr 10, 2016
- Messages
- 232
- Reaction score
- 203
- Location
- United Kingdom
- VCDS Serial number
- C?ID=219022
0x34 is the control module address, which is the air suspension. Therefore the manifold block.
- Joined
- Jan 29, 2014
- Messages
- 21,923
- Reaction score
- 9,308
- Location
- Montgomery, NY, USA
- VCDS Serial number
- C?ID=57337
Man you better start reading the RTFB............
Use the tone generator to sniff it if that hidden to you, further using WD and trace the location by turning the car into a big antenna
Thanks all for helping me to get my Phaeton back on the road. Been driving her again for a week now. The "Running Gear" fault disappeared after I changed relay 214. The front of car lifted after driving around the block a few times. Front right still lowers a bit after its been parked for approx. 8 hours plus, but I guess that could be due to leak as reported by VCDS. Haven't been able to locate leak yet though. I had this issue before but it went after I performed an adaption on controller 34. Another adaption is definitely needed now as the rear stands much higher than it suppose to be, while the front sits below normal. The problem is, the controller still refuses to accept security code (31564) which I have successfully used before. Below is my current VCDS scan.
I am still working to get back to pre KESSY Damage state and better This forum has been of invaluable help. Thanks again guys
I am also finding the Phaeton Self-study program and Elsa workshop manual to be very helpful.
Code:
Thursday,29,November,2018,06:32:41:37723
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 18.9.0.2 (x64) HEX-V2 CB: 0.4436.4
Data version: 20180927 DS296.0
www.Ross-Tech.com
VIN: WVWZZZ3DZD8001098 License Plate: 29-11-6:32
Mileage: 118930km-73899mi Repair Order:
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: 3D-VW61 (6N0)
Scan: 01 02 03 05 06 07 08 09 15 16 17 19 28 2E 34 36 37 38 42 46
47 52 55 56 62 68 6C 71 72 76
VIN: WVWZZZ3DZD8001098 Mileage: 118930km-73899miles
01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
04-Steering Angle -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
06-Seat Mem. Pass -- Status: OK 0000
07-Control Head -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
28-HVAC, Rear -- Status: OK 0000
2E-Media Player 3 -- Status: OK 0000
34-Level Control -- Status: Malfunction 0010
36-Seat Mem. Drvr -- Status: OK 0000
37-Navigation -- Status: OK 0000
38-Roof Electronics -- Status: Malfunction 0010
42-Door Elect, Driver -- Status: OK 0000
46-Central Conv. -- Status: Malfunction 0010
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
55-Headlight Range -- Status: OK 0000
56-Radio -- Status: OK 0000
62-Door, Rear Left -- Status: OK 0000
68-Wiper Electr. -- Status: OK 0000
6C-Back-up Cam. -- Status: OK 0000
71-Battery Charger -- Status: Malfunction 0010
72-Door, Rear Right -- Status: OK 0000
76-Park Assist -- Status: OK 0000
-------------------------------------------------------------------------------
Address 01: Engine (CMV) Labels: None
Part No SW: 03H 906 032 GL HW: 03H 907 309 B
Component: D1-3.6-FSI-AGEU5G 3903
Revision: 5KH07--- Serial number: VWX3Z0L3966034
Coding: 0000175
Shop #: WSC 01065 000 00000
VCID: 72BD2652B8B61427981-5160
3 Faults Found:
008585 - Bank 2; System too Lean at Idle
P2189 - 001 - - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 7
Reset counter: 255
Mileage: 118825 km
Time Indication: 0
Date: 2018.11.25
Time: 14:53:50
Freeze Frame:
RPM: 634 /min
Load: 26.7 %
Speed: 0.0 km/h
Temperature: 85.0°C
Temperature: 47.0°C
Absolute Pres.: 990.0 mbar
Voltage: 14.351 V
008583 - Bank 1; System too Lean at Idle
P2187 - 001 - - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 2
Reset counter: 255
Mileage: 118842 km
Time Indication: 0
Date: 2018.11.25
Time: 15:18:28
Freeze Frame:
RPM: 615 /min
Load: 22.3 %
Speed: 0.0 km/h
Temperature: 82.0°C
Temperature: 36.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 14.351 V
001089 - EVAP Emission Control Sys
P0441 - 001 - Incorrect Flow - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 118847 km
Time Indication: 0
Date: 2018.11.25
Time: 16:13:08
Freeze Frame:
RPM: 633 /min
Load: 22.3 %
Speed: 0.0 km/h
Temperature: 90.0°C
Temperature: 65.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 14.351 V
Readiness: 0000 0001
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 09L-927-760.lbl
Part No SW: 09L 927 760 S HW: GS1 911 4
Component: AG6 09L 3,6 FSI RdW 3603
Revision: --H05--- Serial number: 4636407
Coding: 0000001
Shop #: WSC 01065 000 00000
VCID: 47CBA786E3B4C18F1FF-5160
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 3D0-614-517.lbl
Part No: 3D0 614 517 AK
Component: ESP 5.7 allrad H35 0047
Coding: 0008566
Shop #: WSC 30001 000 00000
VCID: 6B833B369F9CC5EF5B7-51F2
No fault code found.
-------------------------------------------------------------------------------
Address 05: Acc/Start Auth. Labels: 3D0-909-13x-05.lbl
Part No SW: 3D0 909 137 F HW: 3D0 909 137 F
Component: Kessy 6850
Revision: 00H24072 Serial number: VWX3Z0L3966034
Coding: 0151788
Shop #: WSC 01065 000 00000
VCID: 2A0DFE3250B61CE7E01-807E
Subsystem 1 - Part No: XXXXXXXXXXX
Component: ELV XXXX
No fault code found.
-------------------------------------------------------------------------------
Address 06: Seat Mem. Pass Labels: 3D0-959-759.lbl
Part No: 3D0 959 759 CA
Component: Sitzmemory D1 BF 1722
Coding: 0000003
Shop #: WSC 01065 000 00000
VCID: 77AB1746D384710FAFF-8022
No fault code found.
-------------------------------------------------------------------------------
Address 07: Control Head Labels: 3D0-907-048.clb
Part No SW: 3D0 907 048 HW: 3D0 907 048
Component: J127 KBT vorn 0035
Revision: ABH03001 Serial number: VWZ6Z7M0155020
Shop #: WSC 00000 000 00000
VCID: 63935316771C8DAFE37-8036
No fault code found.
-------------------------------------------------------------------------------
Address 08: Auto HVAC Labels: 3D0-907-040.lbl
Part No: 3D0 907 040 M
Component: Climatronic D1 2039
Coding: 0000003
Shop #: WSC 01065 000 00000
VCID: 2809043A4EBA2EF7F65-807C
No fault code found.
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels:. 3D0-937-049-V2.clb
Part No SW: 3D0 937 049 Q HW: 3D0 937 049 Q
Component: J519 7700
Revision: -4006--- Serial number: --------------
Coding: 618C0000EB2915825502770000000000
Shop #: WSC 01065 000 00000
VCID: 3829D47A9E1ABE77665-806C
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 3D0-909-601.lbl
Part No: 3D0 909 601 M
Component: 08 Airbag 8.4E+ H14 1155
Coding: 0012344
Shop #: WSC 01065 000 00000
VCID: 2D07F52E61580BDF053-8078
No fault code found.
-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 7L6-953-549.lbl
Part No: 7L6 953 549 K
Component: J527 3601
Coding: 0000012
Shop #: WSC 01065 000 00000
VCID: 47CBA786E3E4C18F1FF-8012
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments Labels: 3D0-920-xxx-17.lbl
Part No SW: 3D0 920 886 B HW: 3D0 920 886 B
Component: J285 KOMBI-INST. 1521
Revision: KPH06V08
Coding: 0039501
Shop #: WSC 27202 001 104857
VCID: 2A0DFE3250F61CE7E01-807E
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels:. 6N0-909-901-7L.clb
Part No SW: 6N0 909 901 HW: 3D0 920 886 B
Component: J533 GW-K-CAN TP20 1521
Coding: 7FF2F7BEE3011003
Shop #: WSC 27202 001 104857
VCID: 70B92C5AB6AA26376E5-8024
No fault code found.
-------------------------------------------------------------------------------
Address 28: HVAC, Rear Labels: 3D0-919-158.lbl
Part No: 3D0 919 158 M
Component: Klima-Bedienteil D1 0124
Shop #: WSC 00000 000 00000
VCID: 3537DD4E8908431F7D3-8060
No fault code found.
-------------------------------------------------------------------------------
Address 2E: Media Player 3 (J650) Labels:. 5N0-035-342.lbl
Part No SW: 5N0 035 342 F HW: 5N0 035 342 F
Component: SG EXT.PLAYER H18 0530
Revision: A1001003 Serial number: 7662638292
Coding: 020100
Shop #: WSC 01065 000 00000
VCID: 2A0DFE325CF61CE7E01-807E
No fault code found.
-------------------------------------------------------------------------------
Address 34: Level Control Labels: 3D0-907-553-V2.clb
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0007722
Shop #: WSC 28868 001 104857
VCID: 270B070643A4218FFFF-8072
4 Faults Found:
00219 - Loading Level Active
000 - -
01583 - Leak in System Detected
000 - -
01400 - Suspension Level Control
002 - Lower Limit Exceeded
01577 - Turn-Off due to Over-Temp
001 - Upper Limit Exceeded - Intermittent
-------------------------------------------------------------------------------
Address 36: Seat Mem. Drvr Labels: 3D0-959-760.lbl
Part No: 3D0 959 760 CA
Component: Sitzmemory D1 F 1722
Coding: 0000004
Shop #: WSC 01065 000 00000
VCID: 6FBB2F26ABD439CF77F-803A
No fault code found.
-------------------------------------------------------------------------------
Address 37: Navigation (J0506) Labels:. 1T0-035-680.clb
Part No SW: 3D0 035 686 HW: 3D0 035 686
Component: RNS-MID H03 2198
Revision: AB001001 Serial number: VWZ6Z7M0155020
Coding: 06070002000000200000
Shop #: WSC 01065 000 00000
VCID: 639353167B5C8DAFE37-8036
Subsystem 1 - Part No: 7L6 919 859 J
Component: SIMA V4 7769
No fault code found.
-------------------------------------------------------------------------------
Address 38: Roof Electronics Labels: 3D0-907-135.lbl
Part No: 3D0 907 135 F
Component: Dachmodul 0903
Coding: 0012335
Shop #: WSC 01065 000 00000
VCID: 26150A0244AE3887C49-8072
1 Fault Found:
00308 - Supply Voltage for Motors for Sunroof/sunroof Shade
002 - Lower Limit Exceeded - Intermittent
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver
Cannot be reached
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels: 3D0-959-933.lbl
Part No: 3D0 959 933 P
Component: HSG 8135
Coding: 0000040
Shop #: WSC 01065 000 00000
VCID: 3D27C56EB1689B5FB53-4B1E
Subsystem 1 - Part No: 3D2 959 701 L
Component: Tuersteuergeraet FS 6004
Subsystem 2 - Part No: 3D2 959 702 L
Component: Tuersteuergeraet BF 6004
Subsystem 3 - Part No: 3D0 959 703 K
Component: Tuersteuergeraet HL 6004
Subsystem 4 - Part No: 3D0 959 704 K
Component: Tuersteuergeraet HR 6004
Subsystem 5 - Part No: 3D0 909 610 F
Component: 3P HDSG 2630
Subsystem 6 - Part No: 7L0 907 719 A
Component: Neigungssensor 0020
2 Faults Found:
00316 - Bulbs for Rear Illumination
009 - Open or Short to Ground
00896 - Trunk Lock Unit (F256)
008 - Implausible Signal - Intermittent
-------------------------------------------------------------------------------
Address 47: Sound System Labels: 7Lx-035-4xx-47.lbl
Part No SW: 3D0 035 466 D HW: 3D0 035 466 D
Component: R12___DSP 12 Kanal 0570
Revision: DBH06001 Serial number: BP225721243173
Shop #: WSC 00000 000 00000
VCID: 2313131637DCCDAFA37-8076
No fault code found.
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass.
Cannot be reached
-------------------------------------------------------------------------------
Address 55: Headlight Range (J745) Labels:. 5M0-907-357-V3.clb
Part No SW: 5M0 907 357 F HW: 7L6 907 357 C
Component: AFS-ECU H04 0111
Revision: -------- Serial number: --------------
Coding: 012E00000B000200
Shop #: WSC 01065 000 00023
ASAM Dataset: EV_HeadlRegulVWAFSPt 002016
ROD: EV_HeadlRegulVWAFSPt_VW32.rod
VCID: 372BD7469FC4B10F6FF-8062
Left_headlamp_power_output_stage:
Subsystem 1 - Part No: 3D0 941 329 Labels: 3D0-941-329.CLB
Right_headlamp_power_output_stage:
Subsystem 2 - Part No: 3D0 941 329 Labels: 3D0-941-329.CLB
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio (J0506) Labels:. 1T0-035-680.clb
Part No SW: 3D0 035 686 HW: 3D0 035 686
Component: RNS-MID H03 2198
Revision: AB001001 Serial number: VWZ6Z7M0155020
Coding: 06070002000000200000
Shop #: WSC 01065 000 00000
VCID: 639353167B5C8DAFE37-8036
Subsystem 1 - Part No: 7L6 919 859 J
Component: SIMA V4 7769
No fault code found.
-------------------------------------------------------------------------------
Address 62: Door, Rear Left
Cannot be reached
-------------------------------------------------------------------------------
Address 68: Wiper Electr. Labels: 3Dx-955-1xx-V2.clb
Part No: 3D2 955 120 B
Component: Front Wiper 3501
Coding: 0015733
Shop #: WSC 01065 000 376832
VCID: 211F191E2D80DFBFB1B-8074
No fault code found.
-------------------------------------------------------------------------------
Address 6C: Back-up Cam. Labels: 5N0-907-441.clb
Part No SW: 3D0 907 441 HW: 3D0 907 441
Component: J772__Rearview 0020
Revision: 00H11000 Serial number: 525PA8-J231098
Coding: 0000003
Shop #: WSC 01065 000 00000
VCID: 60995C1A664A96B7FE5-8034
No fault code found.
-------------------------------------------------------------------------------
Address 71: Battery Charger Labels: 3D0-915-181.lbl
Part No: 3D0 915 181 F
Component: Batteriemanagement 2800
Shop #: WSC 00000 000 00000
VCID: 26150A0244AE3887C49-8072
1 Fault Found:
00086 - Parallel Battery Connection Relay (J581)
011 - Open Circuit - Intermittent
-------------------------------------------------------------------------------
Address 72: Door, Rear Right
Cannot be reached
-------------------------------------------------------------------------------
Address 76: Park Assist Labels: Redir Fail!
Part No: 3D0 919 283 F
Component: 18 Einparkhilfe 1207
Shop #: WSC 00000 000 00000
VCID: 2D07F52E61580BDF053-8078
No fault code found.
End----------(Elapsed Time: 03:29, VBatt start/end: 11.9V/12.1V)-----------I am still working to get back to pre KESSY Damage state and better This forum has been of invaluable help. Thanks again guys
I am also finding the Phaeton Self-study program and Elsa workshop manual to be very helpful.
Last edited by a moderator:
Troubleshooting advice for my Touareg, the SUV version of your Phaeton, suggests painting the network of tubes exiting the compressor manifold with soapy water to show bubbles. This is under the car below the right front passenger seat.
- Joined
- Jan 29, 2014
- Messages
- 21,923
- Reaction score
- 9,308
- Location
- Montgomery, NY, USA
- VCDS Serial number
- C?ID=57337
I really like foaming glass cleaner for a better visual & as it leaves no residue...............
- Joined
- Feb 25, 2014
- Messages
- 2,780
- Reaction score
- 4,490
- Location
- Cincinnati, OH
- VCDS Serial number
- C?ID=25607
Yeah that's going to be a mild leak somewhere.
You have the exact same level control module as my 2006 W12. That code really ought to work.
Code:
Address 34: Level Control Labels: 3D0-907-553-V2.clb
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0007722
Shop #: WSC 28868 001 104857
VCID: 270B070643A4218FFFF-8072
4 Faults Found:
00219 - Loading Level Active
000 - -
01583 - Leak in System Detected
000 - -
01400 - Suspension Level Control
002 - Lower Limit Exceeded
01577 - Turn-Off due to Over-Temp
001 - Upper Limit Exceeded - IntermittentYou're in loading/transport mode. I bet you need to lay the transport mode disable code on it before it's willing to go through level calibration. Transport mode may also interfere with post-shutdown level maintenance. IIRC, the Phaeton should periodically check and adjust its level for several hours (possibly a day?) after shutdown, but the transport and jack modes will probably disable that. This won't fix your leak either, but it may help a little.
Thanks. The compressor/manifold for my Phaeton sits under the spare wheel well.
Yeah that's going to be a mild leak somewhere.
You have the exact same level control module as my 2006 W12. That code really ought to work.
Code:Address 34: Level Control Labels: 3D0-907-553-V2.clb Part No: 3D0 907 553 C Component: LUFTFDR.-CDC- 3C3V0 1122 Coding: 0007722 Shop #: WSC 28868 001 104857 VCID: 270B070643A4218FFFF-8072 4 Faults Found: 00219 - Loading Level Active 000 - - 01583 - Leak in System Detected 000 - - 01400 - Suspension Level Control 002 - Lower Limit Exceeded 01577 - Turn-Off due to Over-Temp 001 - Upper Limit Exceeded - Intermittent
You're in loading/transport mode. I bet you need to lay the transport mode disable code on it before it's willing to go through level calibration. Transport mode may also interfere with post-shutdown level maintenance. IIRC, the Phaeton should periodically check and adjust its level for several hours (possibly a day?) after shutdown, but the transport and jack modes will probably disable that. This won't fix your leak either, but it may help a little.
Thanks Jyoung.
As soon as I entered transport mode deactivation code, the car went into "lowering ride height" mode, and the rear of car immediately lowered.
The security code (31564) was also accepted by controller. However, when I attempted adaption, it is again requesting security code before channel 01 is even ready for accepting height value.
I will drive her around for a day or two then attempt adaption again if required. Currently the right side of vehicle sits about 10mm lower than left at both front and rear. Left side seem to have correct height for coding 0005521.
Still wondering why transport mode was not disabled since I have been driving this car regularly over 100km/h.
Will update thread in a few days.
- Joined
- Jan 29, 2014
- Messages
- 21,923
- Reaction score
- 9,308
- Location
- Montgomery, NY, USA
- VCDS Serial number
- C?ID=57337
I have seen just a battery reset or voltage discrepancy cause a car to enter transport mode.
- Joined
- Feb 25, 2014
- Messages
- 2,780
- Reaction score
- 4,490
- Location
- Cincinnati, OH
- VCDS Serial number
- C?ID=25607
That's a good step forward!
What faults are currently stored in address 34? By chance did you try clearing fault codes? It may also refuse to adapt if that leak detected fault is stored, for example. I'd park the car on a level surface, clear codes in 34, and then reattempt calibration. If the car can't raise the one side enough to get in calibration range, you might try helping it along with a jack.
Nothing we do with VCDS is going to fix a leak, we're just trying to make it work as normally as possible except for that leak. FYI, it's not unknown for the bags in the air dampers in these cars to leak or fail. There are several companies that will take your damper, rebuild it, and send it back.
I take it you've changed coding recently, because your last Auto-Scan was 07722 (NAR ride height). And if your right side is 10mm below 05521 (Euro ride height) that's pretty low. That's about where it would sit in the automatic high-speed stability mode that you (the driver) can't choose manually.
That coding comment dates back to the original label file authored back in MY2004 by Michael Moore, PanEuropean of VWVortex fame. The rev-C controllers do behave a little different than the rev-A/rev-B controllers in some ways. It wouldn't shock me if transport mode doesn't behave in accordance with the old comment/behavior.
The change was a somewhat infamous vendor change, wherein ALL the original hardware for all 2004s and most (I think) 2005s were abruptly superseded to new and incompatible parts. If an owner had to replace a single air damper, they had to replace all four AND the controller. Here in the US, Volkswagen would eat the extra cost even if the car wasn't under warranty, I think due to regulations requiring 10-year parts availability.
Last edited:
Thanks again for very informative post.
The original code for module was 05521, I had changed it to 07722 when it refused to accept the security pin. With the success I had after your previous post, I reverted to 05521. This is after I was unable to perform adaption and received a fault on the module saying something like "incorrect or no basic setting or adaption" ( which I thought I saved but didn't). Will perform scan again in the morning.
The original code for module was 05521, I had changed it to 07722 when it refused to accept the security pin. With the success I had after your previous post, I reverted to 05521. This is after I was unable to perform adaption and received a fault on the module saying something like "incorrect or no basic setting or adaption" ( which I thought I saved but didn't). Will perform scan again in the morning.
Below is fault code I had yesterday morning.
After performing adaption and driving for about 10 miles, the below fault codes appeared.
The ride height now looks a lot better. The front suspension did not lower overnight - at least not visibly. I will continue to monitor for leaks as repair as necessary.
Thanks a lot for all the assistance received. I still have a lot to learn but I do believe I now know more about this car than the used car dealer that imported it from Singapore, and maybe even more than the local VW/Audi dealer.
Just as observation - I got a "bending light not available (AFS)" error on my MDF display just about the time I had the "no adaptation" controller 34 error. This AFS error disappeared after ride height adaption.
Thanks again guys.
After performing adaption and driving for about 10 miles, the below fault codes appeared.
The ride height now looks a lot better. The front suspension did not lower overnight - at least not visibly. I will continue to monitor for leaks as repair as necessary.
Thanks a lot for all the assistance received. I still have a lot to learn but I do believe I now know more about this car than the used car dealer that imported it from Singapore, and maybe even more than the local VW/Audi dealer.
Just as observation - I got a "bending light not available (AFS)" error on my MDF display just about the time I had the "no adaptation" controller 34 error. This AFS error disappeared after ride height adaption.
Thanks again guys.
- Joined
- Jan 29, 2014
- Messages
- 21,923
- Reaction score
- 9,308
- Location
- Montgomery, NY, USA
- VCDS Serial number
- C?ID=57337
Run car suspension all the way up and all the way down.......... then back up again.
Do this with engine running!
Do this with engine running!
- Joined
- Jan 29, 2014
- Messages
- 21,923
- Reaction score
- 9,308
- Location
- Montgomery, NY, USA
- VCDS Serial number
- C?ID=57337
This means the mechanical basic settings must be reset and checked on the control arms due to being out of range.