Search:

Type: Posts; User: andyhud

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    23
    Views
    10,825

    Thansk sam1754 Yes, it is a little reflective...

    Thansk sam1754

    Yes, it is a little reflective but does work ok. I could always put a sheet of non-reflective clear film over the top to remove that if needed

    Dimensions are very exact for the...
  2. Replies
    5
    Views
    280

    Thanks, are you saying this is possible? If so,...

    Thanks, are you saying this is possible? If so, how do we go about it?

    I dont want to violate any Ross-Tech/VCDS rules at the same time.

    Thanks

    Andy
  3. Replies
    5
    Views
    280

    Thanks Hadez16, appreciate the info. I do...

    Thanks Hadez16, appreciate the info.

    I do understand that VCDS extracts the info from the ASAM data in the experimental coding, but what I'm trying to find out is whether its possible to extract...
  4. Recommended Car Battery Charger / Power Supply

    Just wanted to get throughts on a good Battery Charger for modern start/stop cars when working on them with coding etc (to avoid battery drain etc).

    Normally I would start the engine, but...
  5. Replies
    4
    Views
    129

    Yep, new security feature on new models. Hood...

    Yep, new security feature on new models. Hood must be up
  6. Replies
    2
    Views
    132

    I'm 99.9% sure this can't be done with VCDS.

    I'm 99.9% sure this can't be done with VCDS.
  7. Replies
    5
    Views
    280

    Manual Label Files in LCode

    So I've started using the great LCode.exe "offline" on my desktop computer so I can drop in Long Coding strings and then compare against others the bytes/bits etc. Its very useful

    However,...
  8. Replies
    12
    Views
    417

    Yep, this is spot on Module 42 and 52 Long...

    Yep, this is spot on

    Module 42 and 52
    Long Coding
    Byte 4 / Bit 6
    Its called "mirror_comfort_folding,active"
  9. Did you swap out Your steering unit (J500) with a...

    Did you swap out Your steering unit (J500) with a new one that supports the heated steering wheel? I know you mention slipring, but wanted to be sure...

    Assume you ran power wire for heated...
  10. Replies
    23
    Views
    10,825

    Not specific to the A5 Front Camera but I built...

    Not specific to the A5 Front Camera but I built my own Rear View Camera board as I do a lot of RVC retrofits and while other software can "inject" calibration sets into the 6C camera, I prefer a real...
  11. Replies
    48
    Views
    3,053

    Or that. :) I'd love to know what you built!?!

    Or that. :)

    I'd love to know what you built!?!
  12. What exactly did that change Uwe? Andy

    What exactly did that change Uwe?

    Andy
  13. Replies
    48
    Views
    3,053

    Correct v3.0 have CP. v2.0 don't I have fitted...

    Correct v3.0 have CP. v2.0 don't

    I have fitted SWA to many MLBEvo cars and calibration is only needed if the modules are:

    1. New
    2. Left and right modules were not from same (old) car if the...
  14. 4E is for Rear Seat Entertainment. Its set on the...

    4E is for Rear Seat Entertainment. Its set on the MIB2.

    Go into Adaptation of 5F and look for "Smart Display Carrier 1" or 2 under "Installation List"

    Set it to No, and apply and reboot your...
  15. Replies
    18
    Views
    940

    Hi Akos Yep, that sounds about right. If you...

    Hi Akos

    Yep, that sounds about right. If you have access to the tools, then you should have the files too, and therefore you should be good to upload them

    Assuming of course your thinking the...
  16. Audi Q7 4M Transport Mode Disablement Not working 100%

    Uwe and team

    Friend of mine was doing a controller channel map for me on his 2016 Q7 4M and accidentally clicked on Activate Transport Mode. After doing this he clicked on Disable Transport mode...
  17. Ive seen this before too. Sometimes you need to...

    Ive seen this before too. Sometimes you need to take the neg terminal off the battery for a bit too to let every "reset". Good job :thumbs:
  18. Chances are you dont have motorised mirrors. Its...

    Chances are you dont have motorised mirrors. Its not just coding on the 4M.
  19. Need a bit more than that!

    Need a bit more than that!
  20. Replies
    18
    Views
    940

    Yup. Done it too on a number of A4 B9 (8W)'s. You...

    Yup. Done it too on a number of A4 B9 (8W)'s. You need a new parameter set for the BCM1 Module (09) to get full park assist working. You can code it up in Module 09 and it may "sort of" work but the...
  21. Hi Uwe and team I can confirm that 19.6.0.7...

    Hi Uwe and team

    I can confirm that 19.6.0.7 seems to be working much better than 19.6.0.4 and 19.6.0.6. I have not got a "Function not supported by the Gateway" error and when I do full autoscans...
  22. Thanks Uwe. I'll try over the weekend. Odd...

    Thanks Uwe.

    I'll try over the weekend.

    Odd that you haven't been able to recreate yet I know Jagpurr and he has Hexv2 with same issue and the original OP too of this thread.

    Surely cant be...
  23. Uwe \ Andy This really seems to be a vcds...

    Uwe \ Andy

    This really seems to be a vcds software issue.

    I have 18.9 and 19.6.0.6 running side by side in different installation directories on the same pc.

    Using the same Hex-Net dongle....
  24. Just to let you know I have the same issues too...

    Just to let you know I have the same issues too since updating from 18.9 to 19.6.0.4 and 19.6.0.6. The issue still persists

    I updated my HEX-NET firmware also to latest version when VCDS prompted...
  25. Cheers @Uwe Well , I can confirm ACC worked...

    Cheers @Uwe

    Well , I can confirm ACC worked fine once the bumper was off and back on again. Disconnected the battery first before removing bumper and only reconnected battery once bumper and looms...
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4