Search:

Type: Posts; User: drihos

Search: Search took 0.00 seconds.

  1. down-pipe arrived, waiting on gasket and...

    down-pipe arrived, waiting on gasket and lock-nuts...
  2. Awaiting downpipe to repair exhaust leak. Will...

    Awaiting downpipe to repair exhaust leak. Will clear DTCs and post a fresh Autoscan then. On a side note, my alarm siren is giving it's siren song which may account for some of the intermittent alarm...
  3. Lemme digest that for a minute. Here are the...

    Lemme digest that for a minute.

    Here are the comp test numbers.



    Not sure why I got such a variance on the wet test, maybe the rings are "meh", and the head gasket as well? There is also a...
  4. Which keyway? Damper pulley nub, exhaust cam...

    Which keyway? Damper pulley nub, exhaust cam gear, intake cam reluctor? If it's keyway on tensioner cogs, I'm screwed. The others were thoroughly, if noobishly inspected. The exhaust gear pulley key...
  5. Then there's the powder coated valve cover to...

    Then there's the powder coated valve cover to consider, I did grind down to the grounding post, but I mighta got hasty and not got through all the paint. I think if it was the timing it wouldn't have...
  6. Exhaust cam gear TDC mark lined up neatly when...

    Exhaust cam gear TDC mark lined up neatly when damper pulley mark and notch were at lower cover and cam cap, when I rotated from crank bolt, but would slip back a couple of mm without me keeping...
  7. for the record, I haven't been a huge fan of the...

    for the record, I haven't been a huge fan of the Bentley manual, had better luck on Audizine following along with Diagnosticator and Old Guy. Now I'm wondering if I just didn't know how to read that...
  8. Thank you Jef, for clarifying the three card...

    Thank you Jef, for clarifying the three card monte routine, and stressing the importance of the dealer supplied coils. I burned up some of your time today, but I got good insight from that phone...
  9. No part number on reluctor, came with the cams on...

    No part number on reluctor, came with the cams on the AWM head, actually used that diagram on the ross tech wiki on cam chain position notches and relative pre- oil pressure tension. It got me...
  10. dang it, lemme do some homework now.:) good...

    dang it, lemme do some homework now.:)

    good news is I tracked it to #3 coil. Had misfires on #2 and #3, switched coils outward, logged misfires on #3 and #4. Pulled sparkplugs on #2 and #3,...
  11. but i was told the engine should be warm for a...

    but i was told the engine should be warm for a comp test
  12. no i had not

    no i had not
  13. I hand spun the crank 720deg to check the cam...

    I hand spun the crank 720deg to check the cam belt/chain marks during install, no impingement, marks lined up clean. Had marked my 16 link roller spacing with white-out and triple checked my count....
  14. Just got back from getting coils from the dealer....

    Just got back from getting coils from the dealer. Got a compression tester too. Cleared codes, and shuffled the old coils. Def still a misfire, but no specific cylinder logged on mil at idle. About...
  15. what are the chances its just coils and/or fried...

    what are the chances its just coils and/or fried injector harness wires? It was a swift kick in the nuts to get a misfire after so much attention to detail. Any code-talkers picking up a known fix...
  16. B6 A4 1.8t quattro rebuilt head multiple misfires cyl#2 and #3

    a4 b6 1.8t quattro
    AWM head, port/polished, machine shop seats and valves, decked and dipped.
    new oem head gasket,
    new INA valve seals,
    2 new intake valves,
    all new INA lifters
    short...
  17. Im such a noob. short toggle to switch, 15 second...

    Im such a noob. short toggle to switch, 15 second for password reset.
  18. Any suggestions on how to get it back to wifi...

    Any suggestions on how to get it back to wifi mode? I updated successfully last week, and was able to connect today with the cable to a laptop for tb adaptation. Now I seem to be stuck in...
  19. Sticky: I was in the same boat, bought my hexnet over a...

    I was in the same boat, bought my hexnet over a year ago, never updated it. Talked to Jef yesterday, he walked me through infrastructure mode requirements and told me to unplug and replug the...
Results 1 to 19 of 19