Search:

Type: Posts; User: Golftwincharged

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Dealer online only, I've had this problem...

    Dealer online only, I've had this problem recently, where the component protection was active, and the off button was constantly blinking .
  2. Replies
    4
    Views
    148

    thank you Uwe, i will update you on this.

    thank you Uwe, i will update you on this.
  3. Replies
    4
    Views
    148

    thanks for the reply Mr.Uwe , i get error "no...

    thanks for the reply Mr.Uwe , i get error "no communication with module" .
  4. Replies
    6
    Views
    336

    you will need correct software version for the...

    you will need correct software version for the current car from original tcm, if you have that file and you can flash the replacement tcm, then go ahead, however you dont have that file use the old...
  5. Replies
    4
    Views
    148

    AUDI Q5 STUCK ON START UP SCREEN

    Hey Guys, i have an issue with the display for this vehicle , i am not seeing anything other than the boot screen "MMI Audi Interface" , i checked all fuses are okay, did an optical ring break test...
  6. Replies
    6
    Views
    336

    No immo on this TCM 0AM927769D , all you need to...

    No immo on this TCM 0AM927769D , all you need to do is carried out Basic settings , the 0CW (newer version 0AM) has IMMO locked to unit usually carrying HW number 0AM927769K OR 0AM927769G

    Good...
  7. Replies
    17
    Views
    779

    what are the current codes now? is the magnets...

    what are the current codes now? is the magnets inside gearbox in-tact?
  8. Replies
    17
    Views
    779

    no! once it moves your okay, the fact that it...

    no! once it moves your okay, the fact that it moves not a problem, the lever tool T10407 is applied those forks will feel with tension, if you disengage the lever tool, and check the forks are way...
  9. Replies
    17
    Views
    779

    another fail DSG7 BOX ; common fault is mech unit...

    another fail DSG7 BOX ; common fault is mech unit valve body, and gearbox selector fork ; sounds like the shop didnt do a good job ,troubleshoot as follows :

    1. use vcds "The Removal Position...
  10. replaced TCM, problem solved.

    replaced TCM, problem solved.
  11. Replies
    3
    Views
    219

    Replace the valve body of the mechatronic...

    Replace the valve body of the mechatronic (hydraulics) and that should solve this issue, are you sure this is a "New" mech unit? how did the installation go? as suggested recheck installation ,...
  12. Thanks Jack for your prompt reply! can you...

    Thanks Jack for your prompt reply! can you confirm if this TCM HW and SW is correct according to vin? i noticed previous software differs from current,? may that be an issue? :confused:
    the kessy...
  13. Replies
    6
    Views
    268

    attempt to do basic settings and see what are the...

    attempt to do basic settings and see what are the results? i dont think you will achieve a successful basic settings, sounds like dual clutch is faulty or incorrect installation.
  14. Lost communication with TCM intermittently

    Hey Guys,
    i have an issue with a no communication error with the s-tronic 0B5 TCM,i did a rebuild to the gearbox , also changed the G676 module sensor, also the TCM was replaced with a doner (used)...
  15. this is adaptation issue , please carried out...

    this is adaptation issue , please carried out basic settings as per normal but instead take the RPM around 1200rpm to 1500rpm during the process, it should help P177D fault code and normalise Gearbox...
  16. Replies
    8
    Views
    557

    I've had 3 occasions with this same fault code/s...

    I've had 3 occasions with this same fault code/s and indeed , confirmed this is the fault of the G676 sensor which needs replacing, unforntuately its quite some work to have replaced, which requires...
  17. Another Failed DSG7 mech unit, valve accumulator...

    Another Failed DSG7 mech unit, valve accumulator plate issues, replacing plate will fix this, but can this cause gearbox slipping?? in cases like this you get no gears..
  18. fix engine related issues first.

    fix engine related issues first.
  19. hope that is the issue, please keep us posted...

    hope that is the issue, please keep us posted with the results, thanks!!
  20. This is the DSG 7 0AM dry clutch, many mech unit...

    This is the DSG 7 0AM dry clutch, many mech unit issues relating pressure, this unit needs to maintain between 40 - 60 bars to fully functional and working, air lock can be a problem , also the...
  21. 1.4 tsi squeaks/funny noise on acceleration

    Hey Guys i have an annoying squeak on acceleration maybe around 1500 - 2000 rpm. around the time magnetic clutch engages, have anyone experienced this on the dual charge systems(CAVD,CTHD) ,if so may...
  22. in the mean time you find your auto scan, sounds...

    in the mean time you find your auto scan, sounds like you may have faulty solenoid valves in the mech unit, common problems with the DSG7 05981 /082 , im assuming Basic settings were successful? was...
  23. Replies
    9
    Views
    216

    how can we assist you, if you cant get us...

    how can we assist you, if you cant get us detailed information on this DSG Golf mk7 , where is the Auto-scan?????
  24. Replies
    4
    Views
    129

    soon Jack, the car left the garage, i will update...

    soon Jack, the car left the garage, i will update with auto scan soon, thanks again.
  25. Replies
    4
    Views
    129

    Thank you Jack!! I'm up and running!

    Thank you Jack!! I'm up and running!
Results 1 to 25 of 105
Page 1 of 5 1 2 3 4