Search:

Type: Posts; User: HMC

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    221

    "I’m in Cornwall but on the border with...

    "I’m in Cornwall but on the border with Plymouth."
    VCDS distributor Ilexa is in Truro.
    Regards HMC
  2. Replies
    30
    Views
    781

    "got the parts from an ebay listing...", so...

    "got the parts from an ebay listing...", so almost certainly not genuine VAG!
    Regards HMC
  3. Replies
    5
    Views
    168

    Hi SrapDodger, "Even so, I wouldn't have thought...

    Hi SrapDodger,
    "Even so, I wouldn't have thought that coolant temperature would affect fuel metering.". How wrong you are! You may not have driven anything with a manual choke which you had to...
  4. "Wish I can show you my facebook messenger not...

    "Wish I can show you my facebook messenger not making a living out of this"
    "VCDS Diagnostics
    Yet you have:
    Adaptation | Coding | Diagnostic | Retrofit - London, United Kingdom

    Authorised VW...
  5. Replies
    30
    Views
    781

    Hi maxx6v, ignition on engine not running (KOEO)...

    Hi maxx6v,
    ignition on engine not running (KOEO) the readings should be near enough atmospheric pressure (check with a barometer, Met Office etc), with the engine running depends on the state of...
  6. Hi James, We need a full Auto Scan, but I am...

    Hi James,
    We need a full Auto Scan, but I am assuming you have a diesel Crafter so no throttle body to align.
    Regards HMC
  7. Replies
    2
    Views
    137

    Hi Spider 21, Have you checked for water in the...

    Hi Spider 21,
    Have you checked for water in the ECU connector?
    Regards HMC
  8. Hi Diesel Matt, Your first mistake was to not...

    Hi Diesel Matt,
    Your first mistake was to not set the wheel alignment with the correct equipment. you then compounded this with the " So I tried resetting the ABS module to "factory setting" ". The...
  9. Hi krazyk, Did you do any other work at the same...

    Hi krazyk,
    Did you do any other work at the same time, service/fuel filter? I would be concentrating on the fuel system, start with the low pressure, check pressure etc and work through to the high...
  10. Hi krazyk, I am not sure what you mean by " Took...

    Hi krazyk,
    I am not sure what you mean by " Took of front clip to change passenger side cooling fan", I presume you are talking about the connector. If the non start happened immediately after the...
  11. I trump both of you!:p 1951 and drive whatever I...

    I trump both of you!:p 1951 and drive whatever I need to diagnose, including motorcycles.
    Regards HMC
  12. Hi Fussybob, On a practical point, the symptoms...

    Hi Fussybob,
    On a practical point, the symptoms you describe are typical of a wheel speed sensor signal drop out, in older vehicles a cracked reluctor ring or sensor air gap. In your case a possible...
  13. " I suppose you are going to tell me to go away...

    " I suppose you are going to tell me to go away now !!! "
    No, you could buy VCDS, You won't regret it and it opens up all the free support from this Forum.
    Regards HMC
  14. Replies
    5
    Views
    136

    Hi Sharan1998, Is the floor wet? Convenience...

    Hi Sharan1998,
    Is the floor wet? Convenience Module pretending to be a fish?
    Regards HMC
  15. Replies
    9
    Views
    306

    Hi AshB Was it a brand new injector? What does...

    Hi AshB
    Was it a brand new injector? What does the garage that fitted it have to say?
    Regards HMC
  16. Replies
    2
    Views
    161

    Hi Artic Fox, You don't say what year your...

    Hi Artic Fox,
    You don't say what year your Ducati is, but I would think it has the old Fiat 3 pin connector for diagnostics, so you would need an adaptor to 16 pin. Your best bet is the Android...
  17. Hi jgc1980, Have you checked the battery leads...

    Hi jgc1980,
    Have you checked the battery leads for volt drop under load, particularly the earth? Connect a DVOM between the battery earth and an earth on the engine, crank the engine and tell us...
  18. Replies
    3
    Views
    171

    Thanks Jack, Jeff and Uwe for fixing the code...

    Thanks Jack, Jeff and Uwe for fixing the code tags (I forgot exactly how to do it, nor could I find the instructions),
    Looks like I will have to give this one a miss, it's from another garage...
  19. Replies
    3
    Views
    171

    2013 Q7 J519 question

    Hi Everyone,
    I hope a simple question, I need to replace the J519 Onboard Supply Control Unit because of a supply loss to the R/H headlamp on T10a/4. What I need to know is if Component Protection...
  20. Replies
    4
    Views
    237

    Hi Adecood, As Uwe say's you would only be able...

    Hi Adecood,
    As Uwe say's you would only be able to get OBD related data. You will not be able to access ABS, Instruments, CAN etc. I have used VCDS on a Triumph to look at EOBD data and clear DTC's....
  21. Hi David, As Uwe said, without a DTC it is hard...

    Hi David,
    As Uwe said, without a DTC it is hard to focus on any area, so you need to log whatever data you can, to diagnose what is happening. In addition you may need to manually check things with...
  22. Replies
    38
    Views
    1,390

    Yes, a compression test would be my starting...

    Yes, a compression test would be my starting point, followed by checking for an induction leak.
    Regards HMC
  23. Hi AlixKaur, "when the main beam is on, the...

    Hi AlixKaur,
    "when the main beam is on, the dipped beam turns off", that might be sensible to stop the headlamp and bulb holder melting.
    Regards HMC
  24. Replies
    4
    Views
    503

    Hi nightcasters, The question I have is, were...

    Hi nightcasters,
    The question I have is, were the previous repairs not replacements? if the servo hose was just repaired at the point of the crack, then the answer is yes the part should be...
  25. Hi Karl, I would think a vehicle reboot is worth...

    Hi Karl,
    I would think a vehicle reboot is worth a try, disconnect the battery for 30 mins and then do an autoscan and post it here, then clear all the codes and see what happens.
    Regards HMC
Results 1 to 25 of 166
Page 1 of 7 1 2 3 4