Search:

Type: Posts; User: dnoermann

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds; generated 47 minute(s) ago.

  1. Replies
    11
    Views
    2,106

    So, for PQ25/PQ35 Car's with Component Protection...

    So, for PQ25/PQ35 Car's with Component Protection Master inside the Cluster i figured out the Code.
    You need a ACC Radar and Cluster which are already configured with the right Swap Codes and CP...
  2. Replies
    10
    Views
    366

    ACC-high ==> ACC with max cc Speed 210 km/h ...

    ACC-high ==> ACC with max cc Speed 210 km/h
    ACC-low ==> ACC with max cc Speed 160 km/h
  3. Replies
    22
    Views
    1,055

    Did you clear DTC in 13 ? Acc (13) is...

    Did you clear DTC in 13 ?
    Acc (13) is complaining about Communication errors to every other ECU.
    Is ACC switched on earlier than the rest ?
  4. Replies
    21
    Views
    4,179

    @Sebastian: Just stumbled over your Post. Any...

    @Sebastian: Just stumbled over your Post.

    Any more news regarding the Issues with the T6 BCM ?
    I can confirm this behaviour with my T6 BCM.

    Part No SW: 7E0 937 090 C HW: 7E0 937 090 C
    ...
  5. You are Welcome. The fun Part will be installing...

    You are Welcome.
    The fun Part will be installing the Wire into the ABS ....
    You will have to take a lot stuff apart in the front to get that done.
    Been there, done that :)
  6. The Set Taster is an option :) To Enable TPMS...

    The Set Taster is an option :)

    To Enable TPMS just change coding of ABS Byte 12 set Bit 4.
    In Speedo you need to enable TPMS, too, this bis is labeled in VCDS.

    To Set the OK State, you can use...
  7. Correct, the POLO Guide will work with T5 Model...

    Correct, the POLO Guide will work with T5 Model Year 2010-2015 it is the same Model PQ25.
    MFSW will work, too.
    For CCS you will need the Stalk, CCS as Button in MFSW will not work.
    For CCS wou...
  8. Replies
    12
    Views
    523

    Whell, be the first :)

    Whell, be the first :)
  9. Replies
    12
    Views
    523

    Hallo Alex, cool retrofit attempt. Whell i dont...

    Hallo Alex, cool retrofit attempt.
    Whell i dont know if the T5.2 BCm can do this, but the BCM does have a Coding bit to enable TP1.6 on Engine Can.
    See Picture from VCDS coding here....
  10. You need to change the Coding in SMLS and ECU....

    You need to change the Coding in SMLS and ECU.
    The Bits should by Named in VCDS.
    Remove The Bit @ Adaptive Cruise, or so ...
    Probably you have to Change the Stalk from ACC to CC, too. But i think...
  11. Replies
    7
    Views
    378

    In VW PQ25/PQ35 this is possible. In addition to...

    In VW PQ25/PQ35 this is possible.
    In addition to what Uwe said, you need to change the MFSW from ACC one to the CCS one.
    And do some coding changes.
    I would think that this will be simmilar @...
  12. Just in the Front like in the T6. ...

    Just in the Front like in the T6.

    http://noernet.de/T5.2_ACC.jpg
  13. Replies
    4
    Views
    295

    That ABS PUMP you need, connect it and read out...

    That ABS PUMP you need, connect it and read out the Coding.
    This coding needas to be puttet into the new Pump.
    That is it.
    Or you use the Coding that you will find in your VCDS Autoscan, which you...
  14. Replies
    8
    Views
    469

    Congrats, so your issue is solved now compleetely...

    Congrats, so your issue is solved now compleetely ?
  15. I already did succeed :) ACC is successfully...

    I already did succeed :)
    ACC is successfully retrofittet from the T6, and that needed the T6 Steering-wheel with ACC Buttons.
    BCM used is in the scan in my first Post.
    But still lot of work to do...
  16. Replies
    8
    Views
    469

    The Error regarding the Door Controllers is still...

    The Error regarding the Door Controllers is still there.
    In your scan the Door Controllers as subsystems of the BCM are missing.
    See here, my Autoscan:...
  17. Replies
    8
    Views
    469

    Looks like you disconnected the LinBus which is...

    Looks like you disconnected the LinBus which is going to your door controllers by connecting your MFSW.
    Normly those share the same Linbus pin 17 on BCM.
    Try disonnecting your wire there and look...
  18. Replies
    4
    Views
    295

    Connect your old one, only electricaly, and read...

    Connect your old one, only electricaly, and read out the old config.
    Or look into your last VCDS Autoscan, from there you can read the old config,too.
  19. :) Lets see i have to work some other things out...

    :)
    Lets see i have to work some other things out before i do a howto ...
  20. Hm, that is impossible :rolleyes: May i ask...

    Hm, that is impossible :rolleyes:

    May i ask which exact Year/Month is your Car ?

    Bacause ACC was only available @ the T6, which started in Mid 2015.
  21. The T6 BCM is needed for ACC Retrofit. But the...

    The T6 BCM is needed for ACC Retrofit.
    But the BCM is the easy Part of it.
    ABS, Steering Wheel, Airbag ECU need to be changed, too.
    And Component Protection and SWAP need to be solved, too.
  22. Found the Issue. It looks like the T6 BCM 7E0...

    Found the Issue.
    It looks like the T6 BCM 7E0 937 090 C is not capable of suplying the needed current for the Instrument lighting.
    Thats the source of the lighting fading in and out ....

    With T5...
  23. Replies
    18
    Views
    3,825

    Somnus, apology accepted, all ok :) Please keep...

    Somnus, apology accepted, all ok :)
    Please keep the Data in your Spreadsheet, it was my intention to make this Data public, so better it is available on different places.
    Just add a short link to...
  24. Replies
    18
    Views
    3,825

    Somnus, thanks for sharing the Spreadsheet. But...

    Somnus, thanks for sharing the Spreadsheet.
    But please correct your thanks on the T6 Page.
    I don't know who the person is that you are thanking there, but clearly he just took my work from here:...
  25. You have to look on the differen SW Versions,...

    You have to look on the differen SW Versions, which are in the next line, after the HW Version H62, which is both times the same.

    0400 vs 0973, so they changed a lot ....

    A downgrade of the...
Results 1 to 25 of 59
Page 1 of 3 1 2 3