Search:

Type: Posts; User: mirceaciuciuc

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    1,397

    Hi Uwe, I will do it next time for sure. Now i...

    Hi Uwe,

    I will do it next time for sure. Now i am stuck with it. Big mistake. I have learned my lesson. Now hopefully with the help of you guys I can sorted it out. :)

    Kind regards!
  2. Replies
    21
    Views
    1,397

    Dear Sirs, I have changed the EPB module and...

    Dear Sirs,

    I have changed the EPB module and ABS lost its coding. Can you please help me based on autoscan below with the proper coding for the ABS module?

    Kind regards,

    ...
  3. Yes, there are a few wires that needs connection...

    Yes, there are a few wires that needs connection from the mechatronic to CAN- BUS inside the vehicle to the can bus module. The gear selection electronics needs connections too. Also the mechatronics...
  4. Replies
    6
    Views
    1,892

    I agree with Jack. I hope I am not mistaking but...

    I agree with Jack. I hope I am not mistaking but in the gateway are 3 or 4 can high/low lines, independent and isolated from each other but being able to comunicate between them with the help of the...
  5. So, after inspection of the wire loom that passes...

    So, after inspection of the wire loom that passes by between the oil filter housing and engine block trough the injectors an fuel pressure valves, found that the main black heat protection for the...
  6. It seems to me a fault on the comunication side...

    It seems to me a fault on the comunication side of the modules, maybe a short or disconection on the CAN-BUS lines. Try to see if the Gateway module has all conections in place. I believe it is...
  7. I checked the Glow plug. It has very high...

    I checked the Glow plug. It has very high rezistance. Over 50 ohmís , I donít think it raises any problems that freezes the ECU.
  8. Below the Autoscan ...

    Below the Autoscan


    Thursday,15,February,2018,17:30:30:28047
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
    VCDS Version: 18.1.0.2 (x64)
    Data version: 20180122 DS285.1...
  9. I have checked electrical conections on the...

    I have checked electrical conections on the engine bay fuse panel because were with rust signs. Ignition switch was not checked. What issues can cause the ignition switch? I believe if the switch is...
  10. I donít realy understand what you are saying. If...

    I donít realy understand what you are saying. If you realy want to help somebody it is a good start not to condamn him first if he is doing something wrong.
  11. It sure is as the car is running flawless. The...

    It sure is as the car is running flawless. The retrofit is a success 😬. Checked the PR codes myself before writing the new software on the ECU.

    Just a heads up for anyone trying, be sure to make...
  12. Hi, updating vcds has nothing to do with updating...

    Hi, updating vcds has nothing to do with updating ECU software. This was made with CMD flash tool and the original factory file. Is this what are you refering at?
  13. Passat B6 CBAB engine cut off while driving

    Hello guys,

    I have in my workshop one passat B6 with CBAB engine. The client came in the workshop because the engine while driving starts shuddering on half or full load intermittent and in some...
  14. Hi guys, Talk with the dealership and turns...

    Hi guys,

    Talk with the dealership and turns out the requiring for a new CCS kit with that damn FEC code is imperative, orherwise the function will not work, because the dealer can only use the...
  15. Got it now. Is the swap code universal valid or...

    Got it now. Is the swap code universal valid or do we have to buy a retrofit kit from the dealer to have this swap code.

    Meaning, can the dealer use any swap code from any retrofitting kit to...
  16. Thank you for your reply. CCS in this case is...

    Thank you for your reply. CCS in this case is MFSW based,not on turning stalk. Main difference in this is the coding for steering wheel module that i have sorted out it should be CCS not installed. ...
  17. Hello guys, Golf MK7, same problem with the...

    Hello guys,
    Golf MK7, same problem with the fault code on engine regarding coding of ECU in powertrain data bus after retrofitting CCS.
    Engine code is CRBC, pinout conected from steering wheel...
  18. All sorted out like you said. Updated EDC...

    All sorted out like you said. Updated EDC software with BM version, coded the ECU for automatic transmission and all set up
    perfect. Warning lights off and good to go.
    Thanks!
    All i need is a...
  19. DSG gearbox retrofitted. Manual to DSG swap. Help ABS coding.

    Dear All,

    I have retrofitted DSG gearbox on a 2013 Passat B7. It was initially fitted with manual gearbox.
    I have some issues coding a few of the modules installed. ABS and EPB. Please see below...
  20. Replies
    1
    Views
    2,071

    Seat Toledo 1.4 16V misfire randomly

    Dear all,

    Having this problem with a Seat Toledo that is trowing the following fault codes from time to time toghether with engine running rough for a few moments.


    Address 01: Engine ...
Results 1 to 20 of 20