Search:

Type: Posts; User: Dino20vt

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    389

    Ok will do tomorrow, thanks for the info. Re 77...

    Ok will do tomorrow, thanks for the info.
    Re 77 phone module, if thatís the Bluetooth module under the right hand seat in RHD car, Iíve already removed that, unfortunately made no difference.
  2. Replies
    10
    Views
    389

    No faults shown Dave

    No faults shown Dave
  3. Replies
    10
    Views
    389

    Did the drop test on the main fuses on the end of...

    Did the drop test on the main fuses on the end of the dash and also under the scuttle with all the relays, all behaved as they should.
    Any other fuses elsewhere I can try?
    Thanks
  4. Replies
    10
    Views
    389

    Thanks both for taking the time to reply. Iíll...

    Thanks both for taking the time to reply.
    Iíll give mV drop test a try over the weekend and report back.
    The only fuses I pulled where in the right hand side end panel on a RHD car, do you happen...
  5. Replies
    10
    Views
    389

    Audi RS4 B7 Parasitic Drain

    Iím getting 60-90 milliamps (fluctuates a lot) with car locked and left for an hour to fully shut down. Pulling fuses in the end panel made little difference.
    Is there any other fuses situated...
  6. Replies
    11
    Views
    555

    With regards to the SVM error, I got rid of the...

    With regards to the SVM error, I got rid of the issue on mine by following the guide here:
    https://www.audienthusiasts.com/Application_SVMError.html

    Steve
  7. Replies
    6
    Views
    524

    Presuming it is a M8 bolt, drill into the centre...

    Presuming it is a M8 bolt, drill into the centre with a 5.5mm bit a short depth (if it is 10mm use an 8mm) , this should release the tension in the bolt and allow you to remove it by hammering a Torx...
  8. Replies
    8
    Views
    284

    Thanks, I will give this a go. I have a...

    Thanks, I will give this a go.

    I have a suspicion however that main beam assist will still be active by changing the trigger speeds (i.e. no manual switching of high/low beam) but the assist will...
  9. Perfect thankyou! Error code gone and looks like...

    Perfect thankyou! Error code gone and looks like ACC is working again!

    Thankyou very much for your help!
  10. Thanks, will try that tomorrow. Do i just use 0's...

    Thanks, will try that tomorrow. Do i just use 0's for all of the fields as i am just an individual?

    Thanks, steve
  11. Replies
    8
    Views
    284

    Great thanks, please see my autoscan from tonight...

    Great thanks, please see my autoscan from tonight below:


    Tuesday,04,June,2019,18:42:25:42444
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x86
    VCDS Version: 19.6.0.2 HEX-V2 CB:...
  12. I have tried the coding values you have provided,...

    I have tried the coding values you have provided, they were accepted by the 3 modules but sadly still no good on the ACC unit and it is still showing a fault for incorrect coding:

    ...
  13. Replies
    8
    Views
    284

    There may be on other vehicles but definitely not...

    There may be on other vehicles but definitely not on the 4F A6 MMI 3g.
  14. Replies
    8
    Views
    284

    Hi possibly UK terminology that is confusing....

    Hi possibly UK terminology that is confusing. Main beam = Full Beam.

    I have full beam assist which automatically switches between normal headlights (what i call dipped beam) and main beam when the...
  15. Great thanks, I understand now, I assume I can...

    Great thanks, I understand now, I assume I can test the inputs in the same way using 08-Meas. Blocks to make sure that the microswitches are working on the hitch and release knob?

    Cheers
  16. Hi, Thanks for the speedy reply! Yes it is a...

    Hi,
    Thanks for the speedy reply! Yes it is a manual swivel hitch.
    I will try those codings this evening to check that they work.

    Sorry, not sure what you mean with the activations in the...
  17. Trouble Coding ACC & Engine for Tow Hitch 4F S6

    Hi all,

    I have installed a genuine Audi (Westfalia) swivel towbar and wiring to my 2010 4F S6. The wiring is all correct and I have successfully added module [69] to the CAN gateway. Following the...
  18. Replies
    8
    Views
    284

    2010 A6 4F - disable main beam assist?

    I find the main beam assist feature on my S6 a little tedious and would prefer it to just be manual (as it is when the light switch is not on 'Auto'. Is there any way to disable the full beam assist...
Results 1 to 18 of 18