Search:

Type: Posts; User: HMC

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    27
    Views
    932

    Hi tultalk, A full Autoscan is the place to...

    Hi tultalk,
    A full Autoscan is the place to start.
    Regards HMC
  2. Hi Matttcattt, A simple guage like...

    Hi Matttcattt,
    A simple guage like https://www.ebay.co.uk/i/291752782237 would do for a quick manual check. 2mb at idle doesn't sound plausible, what do you get when revving? I presume you have the...
  3. Hi Matttcattt, "I recently decided to bite the...

    Hi Matttcattt,
    "I recently decided to bite the bullet and replace the DPF, although with an aftermarket one due to cost. ". This will almost certainly come back to bite you, I presume from...
  4. Replies
    13
    Views
    339

    What did you test it with? Without checking my...

    What did you test it with? Without checking my guess is that this could be PWM that needs testing with a scope.
    Regards HMC
  5. Hi fastboat2003, Did you change the module...

    Hi fastboat2003,
    Did you change the module because you had this DTC, or did it appear after you changed the module? Was it dealer new? Has the vehicle been in a collision?
    Regards HMC
  6. Replies
    5
    Views
    451

    In the interest of impartiality I can also say...

    In the interest of impartiality I can also say that Derek at Ilexa gives superb support.
    Regards HMC
  7. Replies
    5
    Views
    226

    Could the Hex Net be providing a better ground...

    Could the Hex Net be providing a better ground for the relevant module?
    Regards HMC
  8. No, but "That is backwards. Driver side is left....

    No, but "That is backwards. Driver side is left. Pass side is right." could be.:)
    Regards HMC
  9. Unless it is RHD! Regards HMC

    Unless it is RHD!
    Regards HMC
  10. Replies
    13
    Views
    449

    "Remove CCM fuse and verify continuity between...

    "Remove CCM fuse and verify continuity between CCM and fuse holder."
    Better to load test it, continuity may not show the fault.
    Regards HMC
  11. Replies
    5
    Views
    389

    If you don't have the tools or the correct...

    If you don't have the tools or the correct information you cannot do the job and your boss needs to be told that. There is a technician skill shortage building up in the UK, if you have the...
  12. Replies
    7
    Views
    259

    Hi Zenerdiode, What do the fuel trims look like?...

    Hi Zenerdiode,
    What do the fuel trims look like? Perhaps log them, the MAF and fuel pressures on the particular hill.
    Regards HMC
  13. "I never did get a heater circuit code after...

    "I never did get a heater circuit code after nearly 40 miles with this setup. any thoughts on why this might be?" Loose pins at the connector made good with the back probe?
    Regards HMC
  14. Replies
    4
    Views
    217

    It may not be Chinese but it is probably faulty....

    It may not be Chinese but it is probably faulty. Get a genuine one from TPS.
    HMC
  15. Replies
    6
    Views
    210

    Have you scoped the signal at the ABS module?...

    Have you scoped the signal at the ABS module?
    Regards HMC
  16. Did this flag the DTC while you were doing this...

    Did this flag the DTC while you were doing this test drive with the scope on? How did you connect the scope leads?

    Regards HMC
  17. Replies
    10
    Views
    302

    I did look in the gateway to see if I could use...

    I did look in the gateway to see if I could use the battery voltage trick but there were no relevant adaptions in the drop down menu. Happy to learn if there is a coding change I can use.
    Regards HMC
  18. Replies
    10
    Views
    302

    Thanks for all the replies, this is a customer's...

    Thanks for all the replies, this is a customer's car and I think I will advise he lives with it.
    Thanks HMC
  19. Replies
    10
    Views
    302

    2015 Scirroco Stop Start disable

    Does anyone have any magic to disable the stop/start on this Scirroco?
    Regards HMC


    Tuesday,14,May,2019,11:32:27:00974
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86
    VCDS...
  20. Replies
    6
    Views
    291

    What condition does this happen at, general...

    What condition does this happen at, general driving, full load acceleration etc? Have you checked for sticking waste gate mechanism/veins?
    Regards HMC
  21. Replies
    6
    Views
    291

    Hi sheepie, Genuine MAF? Have you made sure all...

    Hi sheepie,
    Genuine MAF? Have you made sure all the pipework and vac hoses are in place after the EGR change? Was it a genuine EGR by the way?
    Regards HMC
  22. How are you doing with this? I have just looked...

    How are you doing with this? I have just looked at Elsa and it looks like a standard Zirconia sensor. The 2 white sensor wires are the heater, so with a test light and the engine running check pin 2...
  23. I think I would be scoping the accelerator pedal...

    I think I would be scoping the accelerator pedal sensor for drop outs first. It might be worth putting a bit of sideways pressure on it while checking, sometimes a driving position can make for...
  24. Replies
    15
    Views
    821

    Hi chillout1983, Take it back and get them to do...

    Hi chillout1983,
    Take it back and get them to do it correctly. Would you like to say who did the alignment and what tyres were fitted? Not something like "QuackFat" was it?
    Regards HMC
  25. Hi tomk_22, I am not familiar with US spec cars...

    Hi tomk_22,
    I am not familiar with US spec cars but is the B1S3 O2 sensor not the post cat sensor for OBD emissions checking? If yes then it will not cycle the voltage but have a relatively stable...
Results 1 to 25 of 124
Page 1 of 5 1 2 3 4