Search:

Type: Posts; User: HMC

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    96

    Hi Proffa, Have you checked fuses for the engine...

    Hi Proffa,
    Have you checked fuses for the engine management? ECU does not seem to be awake.
    Regards HMC
  2. FOD strikes again! Oh no, not only am I...

    FOD strikes again!
    Oh no, not only am I beginning to understand Jack, I am starting to sound like him. Is there any cure? :)
    HMC
  3. Replies
    16
    Views
    362

    Hi Gremling, Have you actually tried resetting ...

    Hi Gremling,
    Have you actually tried resetting the SRI via Instrument (17) and adaptions? I do not have problems doing, Reset warning to not active, make sure the mileage and distance for oil...
  4. Hi ak77 Let me translate Jack speak into English...

    Hi ak77
    Let me translate Jack speak into English :)
    This could be a faulty Body Control Module or faulty wiring to it, an incorrect bulb may have a different resistance than the correct one and the...
  5. "I haven’t checked the wiring, I see cable from...

    "I haven’t checked the wiring, I see cable from the rear goes into the body, am I right to think that only the exposed parts of the cable need to be checked?"
    NO!
    As Jack say's, fit genuine parts...
  6. Replies
    8
    Views
    60

    Hi Simon, You should follow Jack's advice but if...

    Hi Simon,
    You should follow Jack's advice but if your main issue is the ABS, the first thing to do is double check the live data from N/S/F wheel speed sensor (G47) and load test the wiring to the...
  7. Replies
    5
    Views
    90

    Hi John, This is really a job for an...

    Hi John,
    This is really a job for an oscilloscope, do you have one? If you have, scoping the powers and signals on the injector and HT coil will give you an idea where the problem lies. As Jack...
  8. Replies
    27
    Views
    1,075

    Hi tultalk, A full Autoscan is the place to...

    Hi tultalk,
    A full Autoscan is the place to start.
    Regards HMC
  9. Hi Matttcattt, A simple guage like...

    Hi Matttcattt,
    A simple guage like https://www.ebay.co.uk/i/291752782237 would do for a quick manual check. 2mb at idle doesn't sound plausible, what do you get when revving? I presume you have the...
  10. Hi Matttcattt, "I recently decided to bite the...

    Hi Matttcattt,
    "I recently decided to bite the bullet and replace the DPF, although with an aftermarket one due to cost. ". This will almost certainly come back to bite you, I presume from...
  11. Replies
    13
    Views
    366

    What did you test it with? Without checking my...

    What did you test it with? Without checking my guess is that this could be PWM that needs testing with a scope.
    Regards HMC
  12. Hi fastboat2003, Did you change the module...

    Hi fastboat2003,
    Did you change the module because you had this DTC, or did it appear after you changed the module? Was it dealer new? Has the vehicle been in a collision?
    Regards HMC
  13. Replies
    5
    Views
    549

    In the interest of impartiality I can also say...

    In the interest of impartiality I can also say that Derek at Ilexa gives superb support.
    Regards HMC
  14. Replies
    5
    Views
    249

    Could the Hex Net be providing a better ground...

    Could the Hex Net be providing a better ground for the relevant module?
    Regards HMC
  15. No, but "That is backwards. Driver side is left....

    No, but "That is backwards. Driver side is left. Pass side is right." could be.:)
    Regards HMC
  16. Unless it is RHD! Regards HMC

    Unless it is RHD!
    Regards HMC
  17. Replies
    13
    Views
    484

    "Remove CCM fuse and verify continuity between...

    "Remove CCM fuse and verify continuity between CCM and fuse holder."
    Better to load test it, continuity may not show the fault.
    Regards HMC
  18. Replies
    5
    Views
    437

    If you don't have the tools or the correct...

    If you don't have the tools or the correct information you cannot do the job and your boss needs to be told that. There is a technician skill shortage building up in the UK, if you have the...
  19. Replies
    7
    Views
    298

    Hi Zenerdiode, What do the fuel trims look like?...

    Hi Zenerdiode,
    What do the fuel trims look like? Perhaps log them, the MAF and fuel pressures on the particular hill.
    Regards HMC
  20. "I never did get a heater circuit code after...

    "I never did get a heater circuit code after nearly 40 miles with this setup. any thoughts on why this might be?" Loose pins at the connector made good with the back probe?
    Regards HMC
  21. Replies
    4
    Views
    241

    It may not be Chinese but it is probably faulty....

    It may not be Chinese but it is probably faulty. Get a genuine one from TPS.
    HMC
  22. Replies
    6
    Views
    218

    Have you scoped the signal at the ABS module?...

    Have you scoped the signal at the ABS module?
    Regards HMC
  23. Did this flag the DTC while you were doing this...

    Did this flag the DTC while you were doing this test drive with the scope on? How did you connect the scope leads?

    Regards HMC
  24. Replies
    11
    Views
    429

    I did look in the gateway to see if I could use...

    I did look in the gateway to see if I could use the battery voltage trick but there were no relevant adaptions in the drop down menu. Happy to learn if there is a coding change I can use.
    Regards HMC
  25. Replies
    11
    Views
    429

    Thanks for all the replies, this is a customer's...

    Thanks for all the replies, this is a customer's car and I think I will advise he lives with it.
    Thanks HMC
Results 1 to 25 of 131
Page 1 of 6 1 2 3 4