Search:

Type: Posts; User: Jef

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Welcome to the Ross-Tech forums. When asking for...

    Welcome to the Ross-Tech forums. When asking for assistance, you must provide a complete Auto-Scan.

    https://forums.ross-tech.com/showthread.php?101-How-to-post-an-Auto-Scan

    Once an Auto-Scan...
  2. Not good. I would say CCV or rear main seal as...

    Not good. I would say CCV or rear main seal as my first guesses. You might want to see about having the crank case smoke tested... blow smoke down the dipstick tube, and see if smoke comes out of...
  3. Replies
    45
    Views
    735

    J519 - T32b/6 (grey connector station) - grey...

    J519 - T32b/6 (grey connector station) - grey wire 0.35mm˛ - tail lights - blue wire 0.35mm˛ - grounded

    Not much there to check.
  4. Thank you for posting an Auto-Scan! :thumbs: ...

    Thank you for posting an Auto-Scan! :thumbs:

    With the the engine at idle and up to temp (+80C), go into the OBDII mode of VCDS. Go to Mode 1. Now pull up long term fuel trim and short term fuel...
  5. Replies
    5
    Views
    61

    Part numbers. Firmware versions. Coding values. ...

    Part numbers. Firmware versions. Coding values. Fault codes. With all the running production changes the Germans do, we don't know what you might have in that car. The Auto-Scan give us details...
  6. Replies
    45
    Views
    735

    If this is all you have, do the figure 8, down...

    If this is all you have, do the figure 8, down the road, figure 8 test drive. Often times it will clear out with that. If not, then as per Jack, you will need to dig into the wiring.
  7. Replies
    5
    Views
    67

    Oh the phone calls we've had from mobile techs at...

    Oh the phone calls we've had from mobile techs at the body shop where the insurance company INSISTED on aftermarket crap. If you go with aftermarket parts, I'd make sure they have an iron clad...
  8. Replies
    45
    Views
    735

    Try doing the Steering Angle Sensor (G85)...

    Try doing the Steering Angle Sensor (G85) Calibration.

    The 01826, in most cases, doing some figure 8s in a parking lot, then drive down the road a mile or 1, more figure 8s, then drive back and...
  9. Replies
    45
    Views
    735

    Unplug the ABS module then replace the fuse...

    Unplug the ABS module then replace the fuse again... if it pops, wiring. If not, looks like an ABS module issue.
  10. Replies
    45
    Views
    735

    /23, 1.0mm˛ sw/br gets power from fuse S7 which...

    /23, 1.0mm˛ sw/br gets power from fuse S7 which looks to be a 10A fuse.... so maybe this just needs fuse S7 to be replaced.

    I would suggest you purchase the cheapest erwin.audi.com package and...
  11. Replies
    45
    Views
    735

    In my drunken state, I kind of messed up like the...

    In my drunken state, I kind of messed up like the dog does to my carpet here in my basement office every damn morning now.... :cry: Your ABS module is dead, I had incorrectly stated it talks VCDS,...
  12. Replies
    10
    Views
    159

    Building on what Jack asked... this might become...

    Building on what Jack asked... this might become relevant as well:

    https://www.myturbodiesel.com/wiki/camshaft-lobe-wear-inspection-and-replacement-on-tdi-pd-engine/
  13. Replies
    45
    Views
    735

    If you play the used parts game, you need to play...

    If you play the used parts game, you need to play by the rules or you gonna have a bad time! :eek:
    https://forums.ross-tech.com/showthread.php?1997-Can-I-go-with-used-parts-Maybe

    As per PL24,...
  14. https://forums.ross-tech.com/showthread.php?101-Ho...

    https://forums.ross-tech.com/showthread.php?101-How-to-post-an-Auto-Scan

    You need to post a full Auto-Scan so everyone can see just what we are trying to help with.
  15. Well, there is the proper way to repair it back...

    Well, there is the proper way to repair it back to factory design, but it requires special toys.

    https://forums.ross-tech.com/showthread.php?15378-Dealer-tools-for-the-simple-things
  16. Take this with a large grain of salt because I've...

    Take this with a large grain of salt because I've not tried this....

    It looks like Adaptation Channel 01 is to shut the ACC system off.

    Start VCDS
    [Select]
    [13-Auto Dist. Reg]
    [Security...
  17. Replies
    2
    Views
    90

    Please try 0004495 for the ABS coding.

    Please try 0004495 for the ABS coding.
  18. The 1st Auto-Scan you posted, VCDS time stamp =...

    The 1st Auto-Scan you posted, VCDS time stamp = Saturday,27,July,2019,14:51:54:45579.
    The 2nd Auto-Scan you posted, VCDS time stamp = Thursday,02,August,2018,18:29:31:45579

    Can you verify an...
  19. When asking for assistance, we ask that you post...

    When asking for assistance, we ask that you post a complete Auto-Scan as detailed here:
    https://forums.ross-tech.com/showthread.php?101-How-to-post-an-Auto-Scan

    I suspect there will be additional...
  20. Is there an Auto-Scan of this vehicle before the...

    Is there an Auto-Scan of this vehicle before the Central Electronics was replaced? If so, please post it. Details on how to find previous Auto-Scan in this video:

    ...
  21. Replies
    0
    Views
    116

    A5 / S5 Cabrio Top operation thread

    Working on the A5/S5 Cabrio top operation video again.

    Current top operation video:
    Note - The control module can only show up to 12 PIDs of data at a time.
    The following video shows 2 different...
  22. Replies
    3,274
    Views
    1,060,070

    https://i.imgur.com/mRGmTpu.jpg

    https://i.imgur.com/mRGmTpu.jpg
  23. Replies
    48
    Views
    79,800

    Sticky: I touched on this already in a recent video: ...

    I touched on this already in a recent video:

    https://i.imgur.com/PLracfx.png
  24. Eos Top Operation via Basic Settings (DO NOT DO THIS)

    There is a method to use a dealer level scan tool like VCDS to operate the top, it is done via Basic Setting. However...

    IT IS VERY DANGEROUS, INJURY AND DAMAGE CAN HAPPEN!!!!!!!!!!!
    IT IS VERY...
  25. https://forums.ross-tech.com/showthread.php?101-Ho...

    https://forums.ross-tech.com/showthread.php?101-How-to-post-an-Auto-Scan

    Once you have the Auto-Scan posted we should be able to get this thread rocking. Staple a few bottles of L&P to your post...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4