Search:

Type: Posts; User: m87a

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    121

    You're right, i'm sorry, my mind is somewhere...

    You're right, i'm sorry, my mind is somewhere else....
  2. Replies
    6
    Views
    121

    you have 5K0-953-549-C module which is Midline...

    you have 5K0-953-549-C module which is Midline and doesn't support cruise control, you will need to replace it with higline module B, or D or E for cruise to work.
    Module does support cruise...
  3. Replies
    17
    Views
    299

    headlights 5N1941033 and 5N1941034 are DLA...

    headlights 5N1941033 and 5N1941034 are DLA headlights and they can work with or without front camera no issues there, I have seen factory configuration with these headlights and no camera or FLA...
  4. Replies
    17
    Views
    299

    check can wires going from 55 to headlights,...

    check can wires going from 55 to headlights, maybe they are swapped? also this local data bus is referring to can bus from 55 to headlights
    Also afs modules on headlights need to support dla, can't...
  5. Replies
    17
    Views
    299

    use vcp to flash tiguan zdc file on 55 use vcds...

    use vcp to flash tiguan zdc file on 55
    use vcds to code 55 for tiguan and Headlights II (DLA)
    connect 55 to extended can, enable extended can in gateway if it's not already
    do auto scan again and...
  6. Replies
    17
    Views
    299

    in your case bcm is irrelevant since AFS module...

    in your case bcm is irrelevant since AFS module is activating stepper motors (via can) for high beams not solenoids powered by bcm
    in bcm change coding
    byte 11 bit 3 activate
    byte 29 bit 3...
  7. sorry can't help you with that, but sw 400 is not...

    sorry can't help you with that, but sw 400 is not available via vw flashdaten, closest one is 412 so try FL_5Q0614517AN_0412.frf on your own responsibility and report back
  8. FL_5Q0614517AF_0398.frf FL_5Q0614517AN_0412.frf...

    FL_5Q0614517AF_0398.frf
    FL_5Q0614517AN_0412.frf
    FL_5Q0614517AR_0642.frf
    these are possible flash files...
  9. thanks for this kamold, didn't know that

    thanks for this kamold, didn't know that
  10. yep, thats it

    yep, thats it
  11. if you install new part which has CP and CP is...

    if you install new part which has CP and CP is flagged as dtc and you reinstall old part, you just need to delete dtc's and that it, it will figure out that everything is as it should be.
    ex
    you...
  12. Replies
    16
    Views
    440

    it's not just coding, you need to upload...

    it's not just coding, you need to upload parameters, vcds can't do that, to upload parameters you need vcp...
  13. Replies
    1
    Views
    121

    Left Low Beam: (1)-Leuchte6ABL LC5-Lasttyp 6 -->...

    Left Low Beam:
    (1)-Leuchte6ABL LC5-Lasttyp 6 --> 3 - Xenon Abblendlicht If your bcm doiesn't support xenon set it to LED Abblendlicht it will work...
    (5)-Leuchte6ABL LC5-Lichtfunktion B 6 -->...
  14. Replies
    16
    Views
    440

    a4 b9 park sensors works as a sub system of bcm...

    a4 b9 park sensors works as a sub system of bcm 09, in order to finish retrofit you need to upload parameters for 8k ops to bcm 09 and code them, the you will have ops system in mmi
  15. 17 byte 4, bit 6 byte 11 bit 1 A5 byte 0...

    17
    byte 4, bit 6
    byte 11 bit 1

    A5
    byte 0 bit 0 or
    byte 16 bit 7

    10
    byte 3 bit 3 or bit 5 (Lane assist)
  16. Had same issue, still not added to label, thank...

    Had same issue, still not added to label, thank you
  17. Replies
    4
    Views
    240

    this can be done with vcp (reading and modifying...

    this can be done with vcp (reading and modifying eeprom values directly), not with vcds, trying different values for byte 18, experimenting, can brick your bcm...
  18. of course 6ohm 50w resistors

    of course 6ohm 50w resistors
  19. Replies
    32
    Views
    1,072

    post full auto scan and code can be generated...

    post full auto scan and code can be generated
    worth to read
    http://forum.skoda-club.ru/viewtopic.php?f=16&t=32543&start=180
  20. Replies
    7
    Views
    373

    You have mk6 cluster which is expecting bcm, but...

    You have mk6 cluster which is expecting bcm, but you have mk5 which have cecm, so convenience menu is missing...
  21. Replies
    55
    Views
    2,724

    can't help with part no. but if your gateway j533...

    can't help with part no. but if your gateway j533 have those pins physically then it does have extended can otherwise no
  22. Replies
    55
    Views
    2,724

    that exactly where it is

    that exactly where it is
  23. did you try to clear errors and then try lights...

    did you try to clear errors and then try lights after you added ground to pin7?
    also check these
    01044 - Control Module Incorrectly Coded
    000 - -
    01516 - Terminal 30; Left
    ...
  24. i have done amarok bi xenon led upgrade and can't...

    i have done amarok bi xenon led upgrade and can't recall but i think that one earth wire was missing check if you have brown wire on pins 5 & 7 if missing splice from other wire, maybe i'm imagining...
  25. Replies
    58
    Views
    21,269

    you should leave things as is, if you downgrade...

    you should leave things as is, if you downgrade acc radar from 3aa to 3c0 you will probably have communication issues because you have gateway from b7 not b6
Results 1 to 25 of 494
Page 1 of 20 1 2 3 4