Search:

Type: Posts; User: DrPeter

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Hi there, after some research, it would appear...

    Hi there, after some research, it would appear that the "Error 212" would set when the Basic Setting has aborted because the pressures did not meet the required amount or the pressure was not held...
  2. Hello, "Error 212" is weird... I suspect the...

    Hello,

    "Error 212" is weird... I suspect the dealer would get the same error. So I would hold off bringing it to the dealer and maybe we can help.

    Do you have a little history? was this ABS...
  3. Replies
    1
    Views
    39

    Hello, This maybe a long shot, but did your...

    Hello,

    This maybe a long shot, but did your customer perform an Auto-Scan of the vehicle prior to any work being done?? (amusing they have a Ross-Tech product)(the internet has seen this VIN...
  4. Replies
    1
    Views
    117

    Hello, We recommend and use the website...

    Hello,

    We recommend and use the website https://www.partslink24.com when attempting to find locate the correct parts as per the VIN.

    I believe you have the [04L 145 049 AA] - Boost pressure...
  5. Replies
    3
    Views
    157

    Hello, Did you happen to notice if the [UDS...

    Hello,

    Did you happen to notice if the [UDS Aggressive Mode] box was checked?
    Typically it is checked by default.

    https://www.ross-tech.com/vcds/tour/screenshots/autoscan-2.png


    Since...
  6. Hello, The fault code in Address [03], The...

    Hello,

    The fault code in Address [03], The ABS Brakes controller below, could be due to a faulty wheel speed sensor.
    We have a Ross-Tech wiki page for that fault code that can help.


    00287...
  7. Replies
    9
    Views
    194

    Hello, This Ross-Tech forum page should be of...

    Hello,

    This Ross-Tech forum page should be of some help for fault codes that end in "Open or Short to Plus".

    Testing - Open Circuits, Short to Ground or Positive, etc....

    Hope this helps,
    ...
  8. Hello, Silly question, but I will ask anyways...

    Hello,

    Silly question, but I will ask anyways .. :) - Have you considered swapping over all the powertrain components? ECM, TCM and ABS? (and others as needed)

    I ask this because I have been...
  9. Hello, I was going to say the same thing, if...

    Hello,

    I was going to say the same thing, if you use the Official Factory Repair manuals, look for the [J345-Towing recognition control module] (It is located in the left rear side panel) there...
  10. Replies
    4
    Views
    94

    Hello, Have you seen this Ross-Tech wiki page...

    Hello,

    Have you seen this Ross-Tech wiki page for the Audi A4 (8E) Automatic Roof?

    I ask because there is a Measuring Value Block chart that can be used to determine what (if any) top switch...
  11. Hi, You are welcome.... Did you register yet? You...

    Hi, You are welcome.... Did you register yet? You really need to register to continue to receive such awesome help ;)

    Thank you,

    drpeter
  12. - You could try it...? Maybe it could help. Try...

    - You could try it...? Maybe it could help. Try clearing codes three times in a row, in less than 30 seconds, then cycle the ignition off, then back on, see what happens.

    We do have this Ross-Tech...
  13. Hello, You too can post a 'fancy'...

    Hello,



    You too can post a 'fancy' Auto-Scan, take a look at this Ross-Tech forum post - How to post an Auto-Scan

    In the mean time you may need to double check your work/repairs. We...
  14. Hi, no worries on the delay, glad you were able...

    Hi, no worries on the delay, glad you were able to post a follow up post here.

    There are small 'clamp-on' style Amp-meters you can get now a days that would be useful in tracking down any suspect...
  15. Replies
    13
    Views
    278

    Hello, That sounds weird... but it also does...

    Hello,

    That sounds weird... but it also does sound rotational, meaning it could be caused by anything that is connected to the crankshaft. You can remove the accessory drive belt to be sure there...
  16. Replies
    8
    Views
    238

    Hi, so does this mean there is no more "telephone...

    Hi, so does this mean there is no more "telephone not available" message? and that you are going to leave the vehicle the way it is?

    drpeter
  17. You are welcome, glad to help. Keep us informed...

    You are welcome, glad to help. Keep us informed and post some pics up if you find/see any carbon in there... Oh and be sure to install the filter so that the filter element end is in direction coming...
  18. Hello, I do not gamble, if I did, I would...

    Hello,



    I do not gamble, if I did, I would say the N80 valve is the logical choice. It is less expensive than a HPFP!!

    The intermittent concern can be explained. Here is one possible reason...
  19. Hi, a leaking N80 valve would most likely lead to...

    Hi, a leaking N80 valve would most likely lead to fuel/fuel vapors migrating into the intake system - ;)

    HPFPs have been known to leak fuel into the engine's crankcase.

    Hope this helps,
    ...
  20. Replies
    8
    Views
    238

    Hi, there is only (30-Power) and the (31-Ground),...

    Hi, there is only (30-Power) and the (31-Ground), CAN bus, antennas, 'telephone bracket' and connections to the Radio and Navigation controllers.

    I would suspect there is a wake-up signal from...
  21. Replies
    8
    Views
    238

    Hello, You may want to verify the...

    Hello,

    You may want to verify the infotainment CAN bus (High/Low) at the R36-Telephone transmitter and receiver unit. The CAN bus signal is a square wave 0V to 5V signal that when checked with a...
  22. Replies
    4
    Views
    226

    Hi, you are welcome. Ugh.. sorry to hear...

    Hi, you are welcome.

    Ugh.. sorry to hear that... VCDS is not going to be able to do any 'flash programing'. Only Basic Settings

    As far as trying to get things done 'quicker', you could find...
  23. Replies
    4
    Views
    226

    Hello, Uwe is correct, there is a concern when...

    Hello,

    Uwe is correct, there is a concern when you have the fault code of P1701-Transmission Control Unit: Locked in memory. Typically the fault sets when the Automatic Gearbox Control Unit–J217...
  24. Is that like a Gold Star? lol Glad it...

    Is that like a Gold Star? lol

    Glad it worked.....

    drpeter
  25. Hello, Based on the VIN, your ABS coding...

    Hello,

    Based on the VIN, your ABS coding should be as follows: [B14B440C492708FC8D1222EB92221061A70000]

    As needed follow the Basic Settings instructions here (1K) Brake Electronics (MK60EC1)...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4