Search:

Type: Posts; User: elqwan

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    238

    Uwe, Well thanks, that really clears it all...

    Uwe,

    Well thanks, that really clears it all up and explains it clearly.

    I still need to download the Erwin documentation, but will the repair manuals and other relevant documentation provide...
  2. Replies
    5
    Views
    238

    For example I was looking at DPF sensor pressures...

    For example I was looking at DPF sensor pressures and soot mass. Not knowing what a reasonable level of soot mass should be or pressure the sensor is seeing, its hard to determine if what I am seeing...
  3. Replies
    5
    Views
    238

    Is it possible to see factory specs in UDS

    My 2016 tiguan is UDS and I noticed that with vehicles that have non UDS modules, when you go into block monitoring you can move the cursor over your current value and it will show you what the value...
  4. So I figured out the issue and yes it makes me...

    So I figured out the issue and yes it makes me feel like an idiot, but the results do confirm a specific suspicion ihad regarding the pressure readings I was seeing from the sensor. I will post the...
  5. I did clear the faults after i installed the...

    I did clear the faults after i installed the sensor. The only wiring I have checked so far was the wiring going directly to the sensor which read 4.9 volts.
  6. Hi, I completely agree with your motto of...

    Hi,

    I completely agree with your motto of teach a man to fish and I appreciate your insight. I will subscribe to erwin and download the repair manual so I have that specific information. I will...
  7. What does it matter if you have not compared them...

    What does it matter if you have not compared them to mechanical gauges and if it's enough to create a DTC what does this determine outside it causes an MIL?[/B]
    -I just figured if I knew if a...
  8. Yeah no worries. I will check again for the...

    Yeah no worries. I will check again for the function but I looked a few times for an adaptation. But maybe its in the wording.

    What do you think about the values I posted above, does anything...
  9. Yes but I couldnt find something specific to...

    Yes but I couldnt find something specific to adapting a dpf pressure sensor.
  10. I am all new to this jack, so I can't confirm or...

    I am all new to this jack, so I can't confirm or deny what you say about the defined values, but i will take your word for it as it makes sense. My thought was that the purpose of the differential...
  11. Would a full dpf set off a code which reads...

    Would a full dpf set off a code which reads Sensor faulty?

    And wouldn’t a blocked dpf be caused from a faulty sensor? The sensor not seeing the filter is getting full? Or why would a dpf filter...
  12. I appreciate your sarcasm. Well my procedure was...

    I appreciate your sarcasm. Well my procedure was this. I checked to see if the lines are blocked. Appears to be good. I checked voltage going to the sensor. All with in spec. So I figured the last...
  13. Iím not sure. Two weeks ago was the first time...

    Iím not sure. Two weeks ago was the first time the car asked to do a Regen. We bought the car new in 2016. I do not feel any loss In power like I would have a blocked exhaust.
  14. So I just went for a 35 minute drive and the mil...

    So I just went for a 35 minute drive and the mil came back on with the same codes.
    I guess I should clear the codes and set a Regen.
    How do I set a force Regen on vcds?
    Iím just wondering why I...
  15. Thanks for your feedback. Since I have...

    Thanks for your feedback.

    Since I have installed this sensor the above fault came back after I cleared the DTC's and drove it for a bit. The other day I did a force regen (the check engine light...
  16. Do I need to adapt a DPF pressure sensor for a 2016 Tiguan?

    I am new to the forum. I have a 2016 VW Tiguan.

    Recently I had a couple fault codes related to the DPF pressure sensor. I checked voltage and blockage. All seemed to be normal so I figured it was...
Results 1 to 16 of 16