Search:

Type: Posts; User: MartinsX

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    31
    Views
    904

    Can You access modules 02, 03 and 37 directly? I...

    Can You access modules 02, 03 and 37 directly?
    I had similar issues in autoscan mode with different cars, mainly when I use my old slow Win XP laptop. Directly modules communicate without any...
  2. Audi TT MK1 Climate Control strange behavior, or should it be so, maybe?

    Car is TT MK1, MY 2000.
    Problem is that air from center vents of dash comes much warmer than from side vents (both).
    Does not matter, what mode is used - auto, econ, recirculation, what flow...
  3. Replies
    4
    Views
    227

    If You still have Your old one unit, You can try...

    If You still have Your old one unit, You can try to put Your original PCB in current pump. ;)
  4. Wiring fault to APP sensors is possible, too,...

    Wiring fault to APP sensors is possible, too, but, based on experience, I'd start with replacing the accelerator pedal with integrated G79/G185. They use to fail on MK4 Golf/Bora or NAR Jetta...
  5. Replies
    4
    Views
    227

    Water ingress into module 35. Maybe not now, just...

    Water ingress into module 35. Maybe not now, just late effect after some water has been there. Or microcontroller chip just starts to go crazy. Those modules used ones are still available for a low...
  6. You are missing taking into account that fuse...

    You are missing taking into account that fuse assignment section is universal overview of what may or may not be connected to/powered from fuses shown there. Exact information is given at *, *1 and...
  7. 1. Post an complete autoscan. Best if You have...

    1. Post an complete autoscan. Best if You have scans with old and with new ECU's.
    2. For that age of TDI/SDI engines there are only two coding options. 00001 for AT and 00002 for MT.
    P.S. Lazy...
  8. I have no personal experience with this exact ECU...

    I have no personal experience with this exact ECU being faulty.
    Have seen some similar faults in 1,6 TDI CR (CAYA/CAYB/CAYC). Sometimes ECU, more often APP sensors.
  9. This is more correct. More 5V consumers than only...

    This is more correct. More 5V consumers than only APP sensor may be connected to ECU via "body harness side" connector.
  10. I have no wiring diagram of Your engine at front...

    I have no wiring diagram of Your engine at front of me at the moment. If we assume that You did all measurements at correct pins, the only conclusion here is - ECU is faulty...
    Last chance - have...
  11. Does the voltage at g79 connector pin 2 remains...

    Does the voltage at g79 connector pin 2 remains 1,4V with G79 disconnected? Was the T60 disconnected during measurements at APP sensors?
  12. I'll try to explain in couple simple words: The...

    I'll try to explain in couple simple words:
    The 12V to 5V converter is inside ECU. This convertor has an overload protection. Output voltage is monitored. If it is out of spec, ECU stores fault...
  13. According OBD mode fault codes there is nothing...

    According OBD mode fault codes there is nothing TB related.
    Try to access module 91 directly, as in autoscan mode it doesn't want to show fault codes. There should be some more accurate fault code...
  14. raw value: 4131.2 hPa This is unreal value. Bad...

    raw value: 4131.2 hPa
    This is unreal value. Bad sensor or damage in wiring to it.
  15. Both wires should have constant voltage. Typical...

    Both wires should have constant voltage. Typical fault of MK5 based cars. Look for damaged wire somewhere behind battery/under battery try. This plastic shit with sharp corners use to cut insulation,...
  16. APP sensors?

    APP sensors?
  17. First thing is to post an autoscan. Second, I'm...

    First thing is to post an autoscan.
    Second, I'm for 99% sure there are no coding or adaptation available to tweak the glow time.
    An old-school method - switch ignition on for approx 20sec (do not...
  18. What is a backstory here? Why ABS need to be...

    What is a backstory here? Why ABS need to be replaced? Is old one totally dead? No communication possible? Is the replacement one the correct part for this car? Do the VIN in 0x01 and 0x25 match each...
  19. And adaptations map of BCM, too.

    And adaptations map of BCM, too.
  20. Hi and welcome! First of all clear all DTC's,...

    Hi and welcome!
    First of all clear all DTC's, run two new scans - one with just ignition on, second with engine @ idle. Post here.
  21. Replies
    9
    Views
    23,437

    The "print to pdf" application installs a virtual...

    The "print to pdf" application installs a virtual printer on Your computer. Then You are able to save anything from Ervin as *.pdf files on Your HDD. Ervin does not allow to download files directly.
  22. What if You run output tests for hydraulic...

    What if You run output tests for hydraulic valves? Does those tests store more fault codes in ABS module? Does the pump motor can be heard when switched on via output test?
  23. Thread: Audi A6 (c6)

    by MartinsX
    Replies
    6
    Views
    252

    Is it working from passenger door switch? I...

    Is it working from passenger door switch?
    I suspect the switch (or wiring to it) in drivers door is faulty.
  24. What is wrong connector with right number? :D

    What is wrong connector with right number? :D
  25. TPMS Reset button: 7E5 927 121 WHS, connector...

    TPMS Reset button: 7E5 927 121 WHS, connector housing 6Q0 972 773 B, contacts 000 979 019 E or 000 979 019 EA (gold plated) for wire cross-section 0,5mm2.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4