Search:

Type: Posts; User: Bwant

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Are you letting the car sleep after coding...

    Are you letting the car sleep after coding changes?
  2. I have seen this too. Strangely, the lights work...

    I have seen this too. Strangely, the lights work fine(fully bright) with the 3C8 'E' but not with the 3C8 'AC'.
    Installing mini leds in the screens is one way of fixing this but it's a fiddly job.
  3. Replies
    19
    Views
    6,757

    I'd be sceptical that HBA is working on that car....

    I'd be sceptical that HBA is working on that car. On the 3C8 CECMs I've seen the HBA/FLA section in adaption is either missing or greyed out.
  4. Replies
    19
    Views
    6,757

    Haha. Well, I'm not holding my breath waiting for...

    Haha. Well, I'm not holding my breath waiting for this scan, but the OP seems pretty sure he's seen this set up so let's see it.
  5. Replies
    19
    Views
    6,757

    Do you have a scan of his car with HBA and 3C8...

    Do you have a scan of his car with HBA and 3C8 CECM?
  6. Replies
    19
    Views
    6,757

    Is HBA available on this module? I was under the...

    Is HBA available on this module? I was under the impression that a 3AA BCM was required.
  7. Replies
    18
    Views
    12,520

    Thanks. I'll buy one and try it.

    Thanks. I'll buy one and try it.
  8. Replies
    18
    Views
    12,520

    I believe I'm on sw1007 at the moment. Is this...

    I believe I'm on sw1007 at the moment. Is this high enough Golfi?
  9. Replies
    18
    Views
    12,520

    So the 'H' version is a direct replacement for...

    So the 'H' version is a direct replacement for the 'F' version or is there a problem with component protection?
  10. Thread: Rvc calibration

    by Bwant
    Replies
    27
    Views
    7,683

    I had this on my CC several years ago....

    I had this on my CC several years ago. Calibration would always fail. What I had to do was place chairs around the calibration board with dark blankets over them to put the board in shadow....
  11. Replies
    6
    Views
    3,071

    Try this... Hold down the 0.0 trip reset...

    Try this...

    Hold down the 0.0 trip reset button, insert key and switch ignition on but don't start engine. You should then be able to reset the oil service reminder.
    To reset the inspection...
  12. Replies
    15
    Views
    6,447

    Just for info the change worked on this door...

    Just for info the change worked on this door controller-2010 Passat CC


    Address 42: Door Elect, Driver (J386) Labels: 3C0-959-70X-GEN4.clb
    Part No SW: 1T0 959 701 AG HW: 3C0 959 793 A
    ...
  13. Replies
    15
    Views
    6,447

    Kamold you have pm.

    Kamold you have pm.
  14. Thanks Golfi. You have pm.

    Thanks Golfi. You have pm.
  15. Thanks for the information Golfi. I don't have...

    Thanks for the information Golfi. I don't have the problem but am considering upgrading from 3C8 920 981 D colour to
    3C8 920 981 G for the 3D display. The sw for the 3D unit is 0705.

    The 981D...
  16. Are there any updates on this? Wondering if the...

    Are there any updates on this? Wondering if the problem is still there with sw 0705?
  17. Replies
    13
    Views
    11,180

    Can you swap the left and right warning lamps and...

    Can you swap the left and right warning lamps and see if the fault follows the lamp or stays at the same side?
    This would prove a faulty lamp or wiring. I'm pretty sure the plugs are the same on...
  18. I don't have 4C in my installed list and never...

    I don't have 4C in my installed list and never have. My ABS based tyre monitoring is activated within my ABS pump coding which I think is +2048.

    Having searched a little about the 4C module, it...
  19. As far as I can remember there is no coding...

    As far as I can remember there is no coding required in the abs module. On my CC I just wired the 65 module to the extended can function of the can bus and ticked it in the installed list.
    If the...
  20. Replies
    17
    Views
    7,239

    Can't you use the volume keys on the steering...

    Can't you use the volume keys on the steering wheel to adjust the volume like the earlier models?
  21. Replies
    9
    Views
    5,710

    http://i1355.photobucket.com/albums/q704/Botty11/i...

    http://i1355.photobucket.com/albums/q704/Botty11/image_zpsg2um3y8h.png

    I found this while searching for the same info. It only shows 1 vehicle type though. Apparently, 74 is the code for VW CC.
  22. Replies
    8
    Views
    5,435

    That's what I was thinking regarding your...

    That's what I was thinking regarding your problem..if the G85 could be set differently. Would you mind sharing the labels with me? For some reason I don't get them all even though my vcds is up to...
  23. Replies
    8
    Views
    5,435

    I was looking at the coding of this module today...

    I was looking at the coding of this module today in my car and some of the labels were not present. Were all the labels present when you coded?
  24. Replies
    8
    Views
    5,435

    How did you code the new module? The labels are...

    How did you code the new module? The labels are incomplete in VCDS and yours look different to others I have seen.
  25. Replies
    5
    Views
    2,964

    I get this when I try to do a full auto scan on...

    I get this when I try to do a full auto scan on my 2002 TDI Passat. Selecting individual modules is fine though.
Results 1 to 25 of 50
Page 1 of 2 1 2