Search:

Type: Posts; User: HMC

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. " Camshaft should be around 400 at idle ". Or to...

    " Camshaft should be around 400 at idle ". Or to be precise half the crankshaft speed.
    Regards HMC
  2. Replies
    7
    Views
    848

    " so expecting a package delivered today from...

    " so expecting a package delivered today from ilexa here in the UK." Good choice, I am sure Derek would always give advice if you are in trouble. The first thing to do is a full autoscan and save it...
  3. Replies
    6
    Views
    198

    If you do change the brake pads, make sure they...

    If you do change the brake pads, make sure they have anti squeal shims and possibly put some anti seize compound on the back of the pads to act as a damper.
    Regards HMC
  4. Replies
    6
    Views
    198

    Hi Volksrabbit, This is not uncommon, it is...

    Hi Volksrabbit,
    This is not uncommon, it is caused by high frequency vibration of the pad, usually because of lip on the brake disk, sometimes it is agravated by cheap replacement brake pads....
  5. Replies
    6
    Views
    556

    Yes, it was under the drivers seat (RHD) hidden...

    Yes, it was under the drivers seat (RHD) hidden under foam, I had to take the seat out to be able to find it. It was water damaged.
    Regards HMC
  6. Replies
    5
    Views
    65

    "I never fitted the egr but I suspect its...

    "I never fitted the egr but I suspect its aftermarket,"
    In my experience aftermarket has a high failure rate. Who fitted it and why are they not fixing it?
    Regards HMC
  7. Replies
    5
    Views
    65

    Hi judge_360, Was it a genuine EGR? What wiring...

    Hi judge_360,
    Was it a genuine EGR? What wiring checks have you done?
    Regards HMC
  8. Replies
    4
    Views
    207

    Hi Proffa, Have you checked fuses for the engine...

    Hi Proffa,
    Have you checked fuses for the engine management? ECU does not seem to be awake.
    Regards HMC
  9. FOD strikes again! Oh no, not only am I...

    FOD strikes again!
    Oh no, not only am I beginning to understand Jack, I am starting to sound like him. Is there any cure? :)
    HMC
  10. Replies
    16
    Views
    500

    Hi Gremling, Have you actually tried resetting ...

    Hi Gremling,
    Have you actually tried resetting the SRI via Instrument (17) and adaptions? I do not have problems doing, Reset warning to not active, make sure the mileage and distance for oil...
  11. Hi ak77 Let me translate Jack speak into English...

    Hi ak77
    Let me translate Jack speak into English :)
    This could be a faulty Body Control Module or faulty wiring to it, an incorrect bulb may have a different resistance than the correct one and the...
  12. "I haven’t checked the wiring, I see cable from...

    "I haven’t checked the wiring, I see cable from the rear goes into the body, am I right to think that only the exposed parts of the cable need to be checked?"
    NO!
    As Jack say's, fit genuine parts...
  13. Replies
    8
    Views
    84

    Hi Simon, You should follow Jack's advice but if...

    Hi Simon,
    You should follow Jack's advice but if your main issue is the ABS, the first thing to do is double check the live data from N/S/F wheel speed sensor (G47) and load test the wiring to the...
  14. Replies
    5
    Views
    99

    Hi John, This is really a job for an...

    Hi John,
    This is really a job for an oscilloscope, do you have one? If you have, scoping the powers and signals on the injector and HT coil will give you an idea where the problem lies. As Jack...
  15. Replies
    27
    Views
    1,170

    Hi tultalk, A full Autoscan is the place to...

    Hi tultalk,
    A full Autoscan is the place to start.
    Regards HMC
  16. Hi Matttcattt, A simple guage like...

    Hi Matttcattt,
    A simple guage like https://www.ebay.co.uk/i/291752782237 would do for a quick manual check. 2mb at idle doesn't sound plausible, what do you get when revving? I presume you have the...
  17. Hi Matttcattt, "I recently decided to bite the...

    Hi Matttcattt,
    "I recently decided to bite the bullet and replace the DPF, although with an aftermarket one due to cost. ". This will almost certainly come back to bite you, I presume from...
  18. Replies
    13
    Views
    385

    What did you test it with? Without checking my...

    What did you test it with? Without checking my guess is that this could be PWM that needs testing with a scope.
    Regards HMC
  19. Hi fastboat2003, Did you change the module...

    Hi fastboat2003,
    Did you change the module because you had this DTC, or did it appear after you changed the module? Was it dealer new? Has the vehicle been in a collision?
    Regards HMC
  20. Replies
    5
    Views
    628

    In the interest of impartiality I can also say...

    In the interest of impartiality I can also say that Derek at Ilexa gives superb support.
    Regards HMC
  21. Replies
    5
    Views
    263

    Could the Hex Net be providing a better ground...

    Could the Hex Net be providing a better ground for the relevant module?
    Regards HMC
  22. No, but "That is backwards. Driver side is left....

    No, but "That is backwards. Driver side is left. Pass side is right." could be.:)
    Regards HMC
  23. Unless it is RHD! Regards HMC

    Unless it is RHD!
    Regards HMC
  24. Replies
    13
    Views
    521

    "Remove CCM fuse and verify continuity between...

    "Remove CCM fuse and verify continuity between CCM and fuse holder."
    Better to load test it, continuity may not show the fault.
    Regards HMC
  25. Replies
    5
    Views
    472

    If you don't have the tools or the correct...

    If you don't have the tools or the correct information you cannot do the job and your boss needs to be told that. There is a technician skill shortage building up in the UK, if you have the...
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4