Search:

Type: Posts; User: Dana

Page 1 of 20 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    7
    Views
    160

    Please use the original coding from the oldest...

    Please use the original coding from the oldest scan but I searched and located 3 RHD 8P chassis cars with this CDLC engine and believe a solid baseline (no VIN Bytes) is:
    ...
  2. Replies
    11
    Views
    221

    Thanks for debugging. When you have a moment...

    Thanks for debugging. When you have a moment please send the resulting files located in C:\Ross-Tech\VCDS\Debug for review. If they don't reveal the problem we will let you know so you can move...
  3. Replies
    11
    Views
    221

    Hi Jerry, I replied to your e-mail with one...

    Hi Jerry,

    I replied to your e-mail with one last suggestion (debug level 1024) before you send the interface to your distributor.

    Best,
    Dana
  4. Replies
    7
    Views
    160

    After reviewing the scans and e-mail I believe...

    After reviewing the scans and e-mail I believe 1K0 907 379 BJ was the factory installed 03-ABS module and the reusing the original coding should be perfectly fine. If you happen to have a scan saved...
  5. Replies
    7
    Views
    160

    Hello Matthew, I'm in the process of updating...

    Hello Matthew,

    I'm in the process of updating your forum status and moving this to the Car Repair Support section. After doing so I'll see if I can make any suggestions that help.
  6. Replies
    5
    Views
    210

    P.S. I never really looked at serial numbers in...

    P.S. I never really looked at serial numbers in those modules but I tend to remove them when I'm posting scan data that I don't have explicit permission to share. In this case that was the new...
  7. Replies
    5
    Views
    210

    Thanks for including the older scan! The...

    Thanks for including the older scan! The original 5K0-953-501-BH module does super several times but the 5K0-953-569-AL unit they sold you appears to be correct. We do have some 5K0-953-569-AL...
  8. Although this is a work-around at best I wanted...

    Although this is a work-around at best I wanted to post this link in the event that another B6/B7 guy has Adp problems before we get a handle on the cause:
    ...
  9. Replies
    2
    Views
    180

    Perhaps a label file for 5F. In that case I...

    Perhaps a label file for 5F. In that case I believe we can redirect it to an existing file (4E0-035-6xx-5F) but Type #1: Control Module Maps would be highly appreciated. If you send them via email...
  10. Replies
    7
    Views
    180

    No, per my explanation via email the vast...

    No, per my explanation via email the vast majority of cold lamp diagnosis bits are controlled by Byte 18 and that's not going to resolve the aftermarket HID light issues. Instead, changing that byte...
  11. Replies
    9
    Views
    182

    Yeah, you should be able to code those modules...

    Yeah, you should be able to code those modules with a current interface. Most will have Experiential Coding but we'll likely need to build you new 01 and 03 coding. When you do get a current...
  12. Replies
    8
    Views
    185

    Advanced Measuring Values are explained here:...

    Advanced Measuring Values are explained here:
    https://www.ross-tech.com/vcds/tour/adv-meas-blocks.php

    Although we'd want to see data from this car you might find my 17-Instruments control module...
  13. Thanks for the feedback and Scan/Debug files via...

    Thanks for the feedback and Scan/Debug files via e-mail.

    This is a long shot but you might want to try increasing the default Blk Int from 55 to 100 (or 150) on the VCDS Program Options screen...
  14. Hi guys, This post ...

    Hi guys,

    This post

    https://forums.ross-tech.com/showthread.php?23131-Figured-out-quot-Ambient-light-2-quot-on-MQB-platform

    .. may add clarity for the next guy.
  15. Searching for J519 would have way too many (851)...

    Searching for J519 would have way too many (851) search results. You would be clicking Next for a while! For that reason using the MEX5R010221-Wiring_Diagrams_and_Component_Locations.pdf diagram I...
  16. Thread: TPMS code

    by Dana
    Replies
    18
    Views
    482

    Since the direct TPMS tweak was un-done in...

    Since the direct TPMS tweak was un-done in address 09 I do not believe the coding needs to be changed in that module to resolve the TPMS code.

    You should be able to reset the indirect TPMS using...
  17. I'm not entirely sure you have the same problem. ...

    I'm not entirely sure you have the same problem. Address 46 (BCM2) has an Intermittent 03123 DTC but 09 (BCM1) which controls the compressor activation does not. Speaking of Intermittent DTCs this...
  18. This should add clarity to VW/Audi current flow...

    This should add clarity to VW/Audi current flow diagrams: https://forums.ross-tech.com/showthread.php?2884-How-to-read-wiring-diagrams-the-videos-(final-version)

    Edit, we have that exact PDF and...
  19. Replies
    7
    Views
    180

    I suspect the factory coding of 09 was something...

    I suspect the factory coding of 09 was something like:


    6F180A1A90272AC4008800C17000054448010386434D8D60648020200040

    Since this BCM probably doesn't have shutter terminals like a BCM with...
  20. Replies
    2
    Views
    86

    I'm thinking AW 07 needs configured via ADP. The...

    I'm thinking AW 07 needs configured via ADP. The PR-Code list is:





    Vehicle Identification No.
    WAUZZZ4F56N045282
  21. Replies
    7
    Views
    169

    Thanks! As long as you are only replacing item...

    Thanks! As long as you are only replacing item #1 (temp link here) that should be plug and play.

    However, if item #2 5Q0 953 549 E is replaced that's the revised version of your #16 module HW:...
  22. LCode2 should have launched a 2nd instance of LCH...

    LCode2 should have launched a 2nd instance of LCH where you can select each Byte and tick/untick all of the Bits. The last time we had a customer with LCode2 issues (the 2nd instance wasn't opening...
  23. Thread: Launch Control

    by Dana
    Replies
    7
    Views
    251

    Correct, in order to confirm abuse. If I was to...

    Correct, in order to confirm abuse. If I was to launch mechanical bits out of the bottom of the trans or burn up dual clutches with regularity (on an in-warranty car) I believe VW/Audi would be able...
  24. Replies
    10
    Views
    206

    Good call. It looks like 8E0-953-549-Q is...

    Good call. It looks like 8E0-953-549-Q is OK/Highline per http://wiki.ross-tech.com/wiki/index.php/Cruise_Control_Retrofitting_(8E)



    Thanks for the photos and clarification. I believe the...
  25. Replies
    8
    Views
    158

    I came up with: 0013755 This page should help...

    I came up with: 0013755

    This page should help after you get it coded:
    http://wiki.ross-tech.com/wiki/index.php/VW_Passat_(3C)_Brake_Electronics
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4