Search:

Type: Posts; User: CuturiloD

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    126

    Audi Q7 2016 rear camera retrofit

    Hello,

    I have new project. This is rear camera for Q7 2016.
    If I have good information for Q7 is neccesary 4M827566 and wiring harnes.
    I dont have wiring diagram and data for long coding.
    ...
  2. Hi guys, As planned, today I went to a service...

    Hi guys,

    As planned, today I went to a service to do an update of the software version.
    When i went out of town and made the first 20km, the warning from the instrument panel disappeared.
    I...
  3. Tomorrow I will go to guy to update my ECU SW to...

    Tomorrow I will go to guy to update my ECU SW to 1649.
  4. Hi guys, I have new info and new scan. This...

    Hi guys,

    I have new info and new scan.
    This morning when I went to work, regeneration was activated. I drove the car until the regeneration was complete.
    Unfortunately the information on the...
  5. I was try to perform regeneration but I can’t. ...

    I was try to perform regeneration but I can’t.
    I have message Aborted-Safety reason.
    I was following all instruction, temp eas above 70, gear position was i N position, etc.
  6. Hi guys, thank You for fast answer. Here is...

    Hi guys, thank You for fast answer.

    Here is the admap engine module:

    SW:04L-906-021-FQ HW:04L-907-309 --- Engine
    Component:R4 2,0L EDC H23 0655, Coding:0A25401A234401080000...
  7. 2015 Audi A6 AdBlue System fault No restart in 1000km

    Hello guys,
    I have problem with AdBlue sistem.
    Yesterday a notice appeared on my dashboard : AdBlue System fault No restart in 1000km.
    https://i.imgur.com/0bWjfgn.png

    First I was read some...
  8. Replies
    48
    Views
    3,312

    I was buy used radars, and after small problems...

    I was buy used radars, and after small problems with wirin instalation everything working perfectly without calibration.
  9. Replies
    48
    Views
    3,312

    If i know it right: 1. When radars are new...

    If i know it right:
    1. When radars are new calibration is required
    2. Calibration is required when radars are used and are not from the same vehicles
    3. Calibration is not required if both radars...
  10. Replies
    48
    Views
    3,312

    Pin 2 is NOT GND, pin 2 need to be +(positive...

    Pin 2 is NOT GND, pin 2 need to be +(positive connection), pin 6 and pin 4 need to be negative connection.
    Try to connect LEDs in oposite way.
  11. Replies
    48
    Views
    3,312

    Hi, I think this is NOT good. Try this : J770...

    Hi, I think this is NOT good.
    Try this :
    J770 pin 6 - - ->pin 1 left LED
    J770 pin 2 - - ->pin 2 left LED, pin 2 right LED
    J770 pin 4 - - ->pin 1 right LED
  12. Replies
    48
    Views
    3,312

    Ok. Can You provide me which pins from SLAVE...

    Ok. Can You provide me which pins from SLAVE module You connected with left LED and right LED?
  13. Replies
    48
    Views
    3,312

    Hello, Can You try to swap LED indicator?

    Hello,
    Can You try to swap LED indicator?
  14. Replies
    16
    Views
    736

    Thank You.

    Thank You.
  15. Replies
    16
    Views
    736

    Hi, now I understand, thank You. Where I can...

    Hi, now I understand, thank You.

    Where I can to find parameters what I need?
  16. Replies
    16
    Views
    736

    Hi, I was also enabled TSR with VCDS and I...

    Hi,

    I was also enabled TSR with VCDS and I also have triangle error in FIS.
    https://i.imgur.com/kSdPZ1m.png

    So, I need to find someone who can finish it using VCP?
  17. Replies
    16
    Views
    736

    Hi. I would be grateful if You could find old...

    Hi.
    I would be grateful if You could find old coding for your RMC 5F
  18. Replies
    16
    Views
    736

    Hello, I was try to coding 5F module as You...

    Hello,

    I was try to coding 5F module as You suggested, but unfortunately without any success.
    On MMI display I don t have any changes.

    Here is the pictures
    https://i.imgur.com/Ga8xAXt.png...
  19. Replies
    16
    Views
    736

    Thank You for suggestion. I will try this coding...

    Thank You for suggestion. I will try this coding when I come home.

    I was coding modules 17, 85 and 8E.
    When I pass by the traffic sign (only speed limit), then I have traffic sign on my...
  20. Replies
    16
    Views
    736

    Thank You @BokiAr for support. As Boki was...

    Thank You @BokiAr for support.

    As Boki was write with modul 5F I have few issuse:
    - Side assist,
    - Lane assist,
    - Traffic sign recognition.

    All of this function is working well done, but I...
  21. Replies
    16
    Views
    736

    Audi A6 C7 modul 5F RMC -help

    Hello everyone,

    I have problem with Long coding and adaptation with 5F modul in my car.
    I don’t have any explanation for long coding also for adaptation.
    If someone have info for my modul...
  22. Replies
    48
    Views
    3,312

    Hello, Unfortunatly with VCDS I dont have any...

    Hello,

    Unfortunatly with VCDS I dont have any explanation about chanel in aptatation windows.
    This is the foto what I have from VCDS:
    https://i.imgur.com/LOljVQO.png...
  23. Replies
    48
    Views
    3,312

    Hello, Thank lot for You try to help me. I...

    Hello,

    Thank lot for You try to help me.
    I was try to follow Your instruction but I was stoped in first step.
    After I was enter security number S12345 VCDS give to me message: security acces...
  24. Hello, is it possible that nobody can help me...

    Hello, is it possible that nobody can help me with my “powerfull” 5F?
  25. 2015 Audi A6 - side assist and line assist - RMC head unit

    Hello,

    I was retrofit side assist and lane assist without stalk in my car. That this issue be realized is also the responsibility of individuals from this forum. :)
    Everything working fine, but i...
Results 1 to 25 of 46
Page 1 of 2 1 2