Search:

Type: Posts; User: HMC

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Hi fastboat2003, Did you change the module...

    Hi fastboat2003,
    Did you change the module because you had this DTC, or did it appear after you changed the module? Was it dealer new? Has the vehicle been in a collision?
    Regards HMC
  2. Replies
    5
    Views
    315

    In the interest of impartiality I can also say...

    In the interest of impartiality I can also say that Derek at Ilexa gives superb support.
    Regards HMC
  3. Replies
    5
    Views
    165

    Could the Hex Net be providing a better ground...

    Could the Hex Net be providing a better ground for the relevant module?
    Regards HMC
  4. No, but "That is backwards. Driver side is left....

    No, but "That is backwards. Driver side is left. Pass side is right." could be.:)
    Regards HMC
  5. Unless it is RHD! Regards HMC

    Unless it is RHD!
    Regards HMC
  6. Replies
    13
    Views
    346

    "Remove CCM fuse and verify continuity between...

    "Remove CCM fuse and verify continuity between CCM and fuse holder."
    Better to load test it, continuity may not show the fault.
    Regards HMC
  7. Replies
    5
    Views
    325

    If you don't have the tools or the correct...

    If you don't have the tools or the correct information you cannot do the job and your boss needs to be told that. There is a technician skill shortage building up in the UK, if you have the...
  8. Replies
    7
    Views
    196

    Hi Zenerdiode, What do the fuel trims look like?...

    Hi Zenerdiode,
    What do the fuel trims look like? Perhaps log them, the MAF and fuel pressures on the particular hill.
    Regards HMC
  9. "I never did get a heater circuit code after...

    "I never did get a heater circuit code after nearly 40 miles with this setup. any thoughts on why this might be?" Loose pins at the connector made good with the back probe?
    Regards HMC
  10. As a fully trained professional mechanic who has...

    As a fully trained professional mechanic who has been in the trade in excess of 50 years, I find Ed China far from a legend. From his descriptions of parts and tools I doubt he is “time served”. If...
  11. Replies
    4
    Views
    177

    It may not be Chinese but it is probably faulty....

    It may not be Chinese but it is probably faulty. Get a genuine one from TPS.
    HMC
  12. Replies
    6
    Views
    174

    Have you scoped the signal at the ABS module?...

    Have you scoped the signal at the ABS module?
    Regards HMC
  13. Did this flag the DTC while you were doing this...

    Did this flag the DTC while you were doing this test drive with the scope on? How did you connect the scope leads?

    Regards HMC
  14. Replies
    10
    Views
    266

    I did look in the gateway to see if I could use...

    I did look in the gateway to see if I could use the battery voltage trick but there were no relevant adaptions in the drop down menu. Happy to learn if there is a coding change I can use.
    Regards HMC
  15. Replies
    10
    Views
    266

    Thanks for all the replies, this is a customer's...

    Thanks for all the replies, this is a customer's car and I think I will advise he lives with it.
    Thanks HMC
  16. Replies
    10
    Views
    266

    2015 Scirroco Stop Start disable

    Does anyone have any magic to disable the stop/start on this Scirroco?
    Regards HMC


    Tuesday,14,May,2019,11:32:27:00974
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86
    VCDS...
  17. Replies
    6
    Views
    246

    What condition does this happen at, general...

    What condition does this happen at, general driving, full load acceleration etc? Have you checked for sticking waste gate mechanism/veins?
    Regards HMC
  18. Replies
    6
    Views
    246

    Hi sheepie, Genuine MAF? Have you made sure all...

    Hi sheepie,
    Genuine MAF? Have you made sure all the pipework and vac hoses are in place after the EGR change? Was it a genuine EGR by the way?
    Regards HMC
  19. How are you doing with this? I have just looked...

    How are you doing with this? I have just looked at Elsa and it looks like a standard Zirconia sensor. The 2 white sensor wires are the heater, so with a test light and the engine running check pin 2...
  20. I think I would be scoping the accelerator pedal...

    I think I would be scoping the accelerator pedal sensor for drop outs first. It might be worth putting a bit of sideways pressure on it while checking, sometimes a driving position can make for...
  21. Replies
    15
    Views
    707

    Hi chillout1983, Take it back and get them to do...

    Hi chillout1983,
    Take it back and get them to do it correctly. Would you like to say who did the alignment and what tyres were fitted? Not something like "QuackFat" was it?
    Regards HMC
  22. Hi tomk_22, I am not familiar with US spec cars...

    Hi tomk_22,
    I am not familiar with US spec cars but is the B1S3 O2 sensor not the post cat sensor for OBD emissions checking? If yes then it will not cycle the voltage but have a relatively stable...
  23. Replies
    15
    Views
    563

    Let us have your postcode and see if anyone is...

    Let us have your postcode and see if anyone is near you.
    Regards HMC
  24. Replies
    2
    Views
    197

    Hi Tom, Have you been here...

    Hi Tom,
    Have you been here http://wiki.ross-tech.com/wiki/index.php/P334B/013131 ? It would be an idea to log IDE03931-ENG102825 Charge pressure actuator: actual position and IDE03932-ENG103291...
  25. Replies
    101
    Views
    2,620

    Everything you say is so true except "Yeah all of...

    Everything you say is so true except "Yeah all of that would not exist of Ewe and co couldn't make a living at it"
    It's Uwe, he is not a sheep.
    Regards HMC
Results 1 to 25 of 120
Page 1 of 5 1 2 3 4