Search:

Type: Posts; User: Pinpointdiag

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Hi did you remove the haldex controller with...

    Hi did you remove the haldex controller with vehicle on the ground? If so then checking the feed and earth and the CAN at the 8pin plug should be possible. A load test with a bulb for the feeds and...
  2. Your original question asked why the abs, Tpms,...

    Your original question asked why the abs, Tpms, handbrake, lights are coming on. And you will fix the engine fault later, but I would suggest all your other lights are just due to the fuel trim fault...
  3. Audi A3 3.2 BUB engine, possable cam timing error.

    Hi, Can any one confirm for me what i suspect is happening with an Audi a3 I'm looking at.
    The vehicle has had a timing chain replacement done by a previous garage. It then ran fine for a couple...
  4. 2010 audi a3 2.0ltr common rail, CFFB engine. fuel pressure fault.

    Hi I have a problem with an A3 that belongs to a motor trade customer, The previous history is unknown and it was bought at auction with this
    fault.
    The car starts and runs every time although it...
  5. Replies
    44
    Views
    14,418

    For example by scoping the rail pressure sensor...

    For example by scoping the rail pressure sensor and an injector on the car you could see this kind of thing, pressure drop on pressure sensor when injector opens with out removing injector and having...
  6. Replies
    44
    Views
    14,418

    Has this car got a Dpf? So the car can run fine...

    Has this car got a Dpf?
    So the car can run fine hot and cold with no smoke and then intermittently there is a sudden and large release of thick white smoke is that what you are saying?

    It's not...
  7. B1S1 is at 1.6v so i would think it is a wide...

    B1S1 is at 1.6v so i would think it is a wide band sensor. if so then there wont be much variation from that you will have to look at the lambda eqiv values
    and the current demand from the sensor to...
  8. Ah ok Jack I'll try again.

    Ah ok Jack I'll try again.
  9. Replies
    6
    Views
    7,679

    It will start happily with the faulty injector...

    It will start happily with the faulty injector unplugged and run on three cylinders. If it's that.
    Usually a short to ground in the pizo stack in one injector. You can un plug each one at a time and...
  10. Hi. I would suggest that given the pervious...

    Hi. I would suggest that given the pervious engine fault the cat is now failing. If you can scope test front and rear O2 sensors
    At 2000 rpm with cat hot and the rear sensor has any switching...
  11. Yes but as this car has mk60 abs I think that is...

    Yes but as this car has mk60 abs I think that is the wrong procedure. the steering angle sensor basic settings are done in the abs controller according to rosstech wiki. Mk70 in 0x44 mk60 in 0x03...
  12. Sorry Jack it's been almost three weeks since I...

    Sorry Jack it's been almost three weeks since I last asked about this car. You were helping and advised I try 0x44 10 000
    Sorry if I have confused things. I know the procedure for basic setting for...
  13. Hi again back on this. There is no deviation...

    Hi again back on this.
    There is no deviation between all four wheels when driving 5-20 mph. I also checked with scope but only two post lift so front ones driven rear ones spun by hand.
    no drop...
  14. I have a Snap-on graphing scan tool that's very...

    I have a Snap-on graphing scan tool that's very good and quick to check wheel speeds, any I have seen in the past
    were picked up by this. However I also have a four channel pico scope. Do you think...
  15. Ok will be Monday now before I can get back to...

    Ok will be Monday now before I can get back to this.

    The rack with 0x44 had been removed and refitted by previous garage. However I
    did have the wiring out so I could plug It in to the old one...
  16. Hi again, yes tried that and although 000 is not...

    Hi again, yes tried that and although 000 is not in the drop down box. If I try it anyway it says reset to factory basic.
    Done that rebooted everything even tried disconnecting car battery for a...
  17. Hi is this is this the screen capture you wanted...

    Hi is this is this the screen capture you wanted

    http://postimg.org/image/c03by1oxn/

    http://s33.postimg.org/6bx175klb/vcds_screen.png
  18. Is there an easy way to post a screen shot

    Is there an easy way to post a screen shot
  19. Ok in address 44 . Can't log in with 40168 in...

    Ok in address 44 . Can't log in with 40168 in security access 16 but in coding 11-11 it says log in accepted
    Then in basic settings it has steering angle sensor only. which under documented basic...
  20. Hi Jack thanks for your reply. Can I ask if you...

    Hi Jack thanks for your reply.
    Can I ask if you can expand a little. You are correct in my laptop the wsc importer and tester were all zero.
    I have changed that. Switched off rebooted laptop
    Am...
  21. Replies
    16
    Views
    4,146

    Hi in live data for engine ecu are you seeing...

    Hi in live data for engine ecu are you seeing correct cranking speed when you are trying to start.
    no crank sensor input, no fuel pump relay pull in, other then maybe a couple of seconds for priming...
  22. Here is the most recent auto scan of the Golf...

    Here is the most recent auto scan of the Golf
    Cheers Alan



    Tuesday,24,May,2016,19:37:31:05279
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 7 x86
    VCDS Version: 15.7.4.1
    Data...
  23. MK5 Golf 1K Problem calabrating steering. code 02546 and 00778

    Hi all. Can i ask for advice with this one please, i know it can cause problems and i have read lots of posts here. And I have have read and followed the instructions on the wiki. This car has ate...
  24. Hi i have just noticed the code for the extra...

    Hi i have just noticed the code for the extra sensor has gone in the new module. i cleared all the codes. in both modules today before running the scans.
    To be honest i was thinking more about...
  25. Hi Uwe, Thanks here are the auto scans from the...

    Hi Uwe, Thanks here are the auto scans from the car. The first one is with the old module. the second is with the new one.


    Sunday,07,June,2015,14:41:14:05279
    VCDS -- Windows Based VAG/VAS...
Results 1 to 25 of 26
Page 1 of 2 1 2