Search:

Type: Posts; User: Shzeps

Search: Search took 0.02 seconds.

  1. Readiness script error 1Y 2005 New Beetle BEV secondary air

    Hi Group,

    I needed to complete readiness on this 1Y 2005 New Beetle BEV.

    I used the VCDS readiness script to complete this. I have a problem when it tries to run the monitor for secondary air....
  2. Replies
    3
    Views
    206

    Thanks for the replies. I was also thinking that...

    Thanks for the replies. I was also thinking that I had a latch issue however the only way I was going to check the harness and prove there is a latch motor failure was to test at the control unit...
  3. Replies
    3
    Views
    206

    2004 Beetle Convertible Actuation 1Y

    Hi Group,

    I have a problem with the convertible top and suspect the rear latch motor. MVB 1,4 (convertible top switches II) value is 000011 when the top stops while opening (top all the way open,...
  4. Just checking, did I post this in the wrong...

    Just checking, did I post this in the wrong forum? Please let me know.

    Thanks.
  5. Reset timing chain stretch adaption and oil pressure break in

    Hi,

    Is there a way to reset timing chain stretch adaption and oil pressure break in on newer 2.0l FSI AND TFSI engines (ex: CAED, CCTA, etc.) after replacing the timing chain and tensioner? There...
  6. Replies
    3
    Views
    215

    2014 EOS CSC conoof emergency operation

    Hi Group,

    Is there a function in VCDS to activate a 2014 VW EOS CSC convertible roof emergency open close functions like Autologic (I just watched a video on this...
  7. No everything is stock. I will keep an eye out...

    No everything is stock. I will keep an eye out for another car with a PD DTC and then see if it is detected by VCDS and report back.
  8. Uwe would it help to log anything and send it. I...

    Uwe would it help to log anything and send it. I would be glad to help further development.
  9. I am sure it did have misfires at some point....

    I am sure it did have misfires at some point. This is a shop car and has been sitting around for a while.

    Here is a pic of the codes.

    https://i.ibb.co/chSvCBb/PD-DTC.jpg
  10. Auto-Scan

    Here is the Auto-scan. Please let me know if and what I should log and send in.



    Tuesday,08,October,2019,16:26:15:57829
    VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
    VCDS...
  11. 2012 8R Q5 OBD Mode 10 Permanent codes not shown

    Hi, I used VCDS 19.6.2 with HEX-NET to set all readiness on this car. When it went for a smog (CA) it failed for permanent DTC P0300 and P0301 misfire. I went back with VCDS into the OBD function and...
  12. Replies
    1
    Views
    686

    Printing VCDS log with color

    Hi,

    Is there a way to print an autoscan to PDF in color (codes in red) either from the autoscan screen or VCDS toolbox?

    Thanks for any info,

    Shep
  13. Thank You all for your help and advice. I...

    Thank You all for your help and advice.

    I actually had coded it before posting using almost the same configuration as NEtech suggested, but I used JCB instead of Varta. I didn't know which brand...
  14. BEM Battery replacement coding no serial number

    Hi Group,

    I have a question about BEM battery replacement and coding.

    Please refer to the image. It shows both the old and new batteries.

    The battery is labeled with both Varta and JCB,...
  15. UDS advanced measuring values descriptions and acronyms

    Hi,

    I am starting to see more cars with UDS protocol.
    Is there a master list for UDS advanced measuring values abbreviations and descriptions of what the value is displayed in VCDS?
    Is there any...
  16. HEX-NET IOS full version request without cloud

    Hi,

    I just upgraded to HEX-NET from a USB cable and think it's great.

    I like how the full version of VCDS can be installed on a PC and work just like it did before.

    Is there a way to...
  17. 2002 JETTA Runs rough only with cam sensor connected

    2002 VW JETTA AVH 2.0

    Hi Group,

    Originally towed into the shop for a clutch problem. When we started it up it had a long cranking time or started and died a few times before it ran.

    I...
  18. Thread: Hello Group

    by Shzeps
    Replies
    2
    Views
    1,666

    Hello Group

    Hi to all. I am a longtime user and fan of VCDS in the USA. This looks like a great forum. I am looking forward to learning from and contributing to this group.

    Shep
Results 1 to 18 of 18