Search:

Type: Posts; User: MasterTommy

Page 1 of 18 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Mr

    by MasterTommy
    Replies
    2
    Views
    47

    This has got to be the number one entry in a...

    This has got to be the number one entry in a certain competition.
  2. Replies
    3
    Views
    78

    Programming not sure. However, recent models have...

    Programming not sure. However, recent models have two fuse sockets for the cigarette socket, one being permanently live and the other having a switched power supply. Swapping the fuse over will...
  3. Replies
    6
    Views
    121

    If its a 2-wire sensor, try measuring resistance...

    If its a 2-wire sensor, try measuring resistance between the sensor and the other end. Whatever control unit itís connected to does the same, and resistance in the wiring/connectors will thus...
  4. Replies
    2
    Views
    69

    Not sure if it’s possible, but if so you will...

    Not sure if it’s possible, but if so you will still pay the same price as the two-step upgrade, since the vin-limits are there to be able to offer a lower priced version to make the interface also...
  5. As far as i know, the antenna amplifier and the...

    As far as i know, the antenna amplifier and the amplifier with QI charging fit the same slot, so if i had a car with none of these, i would go for qi charging as well...
  6. Replies
    15
    Views
    760

    Brake fluid exposed to air deteriorates rapidly....

    Brake fluid exposed to air deteriorates rapidly. If someone takes a caliper or a master cylinder and leaves everything hanging, the pump will be dead in weeks/months.
  7. Replies
    8
    Views
    144

    We dont know, because you need to post 1: full...

    We dont know, because you need to post 1: full autoscan, and 2: provide details on what you are trying to do.

    Guessing is kind of a waste of time...
  8. Replies
    15
    Views
    760

    You could running the abs output test (bleed...

    You could running the abs output test (bleed procedure)? At least the valves will be actuated then.
  9. 1. Autoscan 2. Replacement light = same HW/SW...

    1. Autoscan
    2. Replacement light = same HW/SW part no, dataset, software version, coding?
  10. Replies
    12
    Views
    369

    Installed that too on my tiguan. Front door...

    Installed that too on my tiguan. Front door modules already use the door exit light for the illuminated door sills. The rear modules however are free, you will need to enable the bit for the door...
  11. Replies
    5
    Views
    172

    Limp mode means some sort of fault was logged....

    Limp mode means some sort of fault was logged. However, i see none in your scan. And im not a big fan of guessing games... :D
  12. Replies
    3
    Views
    150

    I think you need to fix the immobilizer mismatch...

    I think you need to fix the immobilizer mismatch first.
  13. Is there a sensor on the battery negative...

    Is there a sensor on the battery negative terminal connector, and is it plugged in or was it damaged during battery replacement?
  14. I see the sensor in the scan, yeah. Still the...

    I see the sensor in the scan, yeah. Still the wrong one.
  15. 00 means the light configuration is not equal to...

    00 means the light configuration is not equal to any of the available 'presets' selectable by picking a value for that byte. Rather it is a light configuration loaded directly into the BCM. There is...
  16. I would like to add to this that most MQB EU cars...

    I would like to add to this that most MQB EU cars with upgraded climatronic get a residual heating function automatically. Which is in no means an auxilary heater, but every single car that has a...
  17. Replies
    10
    Views
    185

    Thats why you do the basic setting, to relearn...

    Thats why you do the basic setting, to relearn the end stops. But if you release too soon during the second push nothing is saved.
  18. Replies
    10
    Views
    185

    Adjust the seat in a single direction until it...

    Adjust the seat in a single direction until it stops by itself. Then hold the button again in the same direction for about 5-10 seconds. This way the end stops are relearned. Repeat this for every...
  19. 1: Mount module in the oem position with the...

    1: Mount module in the oem position with the original bracket. Do not DIY the TPMS module location or you will keep wasting time on this.

    2: Load parameters using ‘that other tool’ if ODIS wont...
  20. I don’t know about the first two, but since a Q2...

    I don’t know about the first two, but since a Q2 is an MQB car, its a definite no on the stop-start.
  21. Replies
    10
    Views
    652

    Wait, I thought with UDS modules available...

    Wait, I thought with UDS modules available channels would always show in the map?
  22. Replies
    3
    Views
    136

    My best guess is somebody replaced the door...

    My best guess is somebody replaced the door control modules left and right. Check if the partnumbers are correct, and if so they probably need parameters which VCDS cannot do.
  23. Replies
    11
    Views
    441

    In the car settings in the MMI you should be able...

    In the car settings in the MMI you should be able to change the pre-warning settings as well. This usually doesnt require VCDS.
  24. Half of those errors only have a frequency of...

    Half of those errors only have a frequency of one.

    Best bet is to check the system for leaks and fix them. All those pressure sensor faults could also trigger the control module to believe there...
  25. I have a 9.2 MIB and ive tried every adaptation...

    I have a 9.2 MIB and ive tried every adaptation channel and combination that i could think off (with a million resets) but no joy. If you enable developer mode you can see with some digging that...
Results 1 to 25 of 436
Page 1 of 18 1 2 3 4